HAZET – Safety Spring Vice 4900

More documents

Recommendations

Info

Ingenious ToolsSpecialty ToolsChassis – Shock Absorbers / AxlesWheel Hub and Drive Shaft (Half Shaft) Puller34 Parts, DBGM – German Registered Utility Modelwith hydraulic spindle suitable for impact operationIncluding operating instructions with 3-dimensional illustrationsSoft-foam insert7Drive Shaft /Half ShaftWithout O-RingInner O-RingSliding mechanismRemoving the drive shaft(half shaft) on vehicles onwhich the strut unit must notbe completely dismounted.Removing a wheel hubwith inner O-ringRemoving a wheel hubwithout O-ringThe sliding flange plate can be usedfor 4 and 5-bolt rimsThe hydraulic spindle can beoperated with impact wrench.Max. load 100 KN (^= 10 tons)Sectional View onImpact SocketSafetyshearing pinSpecialHAZETdriveThe safety shearing pin preventsoverload (overload protection).The special HAZET drive (DBGM)prevents the spindle from breakingaway when threading it completelyinto the hydraulic cylinder.• No pressing or impact forces – therefore damage-freeremoving of the wheel hub• Time-saving: 30 minutes less of work for removing the wheel hub ofthe built-in rear axle, as the following works are not necessary:removing the axle body / removing the hand brake cable/removing theABS-sensor / removing the brake lines and brake ventilation• Modular assortment consisting of 34 parts, suitable for:AUDI A4, A6, BMW E 36, E 46, E53, E60, E61, E83, E90, E91, E93,VW Golf III and IV, Passat, FORD Focus, Mondeo, RENAULT Mégane,Scénic, Clio, OPEL Astra F, PEUGEOT• Removing the drive shaft (half shaft) on all vehicle types on which thecomplete dismounting of the strut unit is not necessary• Saving money as camber adjustment is not necessary• Very sturdy, even for continuous use of impact wrenches1 44935-1/34 121441204 Components and Spare Parts see pages 228 to 236
Specialty ToolsChassis – Shock Absorbers / Axles / BrakesIngenious Tools49354955Wheel Hub Puller1 4C/BrakesBrake Fluid TesterAKR&Hydraulic spindle, mechanical Ä 17 mm, stroke 35 mm4935-1 119493Flange plate for mechanical spindle 4935-14935-2 119486Thrust bolts (2 pieces)4935-3 119479Pressure rail 4-bolt wheel hub4935-4 120505Pressure rail 5-bolt wheel hub4935-5 119974Thrust mandrel 65 mm4935-6 120031Thrust mandrel 115 mm4935-7 119820Thrust ring4935-8 119462Location bolt for machinist’s vice4935-9 120192Spindle drive j 12.5 = 1 ⁄2”4935-10 128778Thrust ring, complete, bearing diameter 82 mm4935-25 120185Thrust ring, complete bearing diameter 75 mm4935-25 A 120215Thrust ring, complete for BMW4935-29 120154Shells (pair) for VW, FORD, PEUGEOT, RENAULT, OPEL4935-72 119813Shells (pair) for FORD Mondeo4935-75 119806Shells (pair) for PEUGEOT4935-82 119790Threaded bolts (3 pieces)4935 IG- M 12 x 1,5 1197764935 AG-M 12 x 1,5 1197454935 AG-M 14 x 1,5 119769Fixation set4935-M 12/9 121458Additionally availableThrust ring, complete for FORD4935-34 120147Track Rod Wrench• Portable (for everywhere use) – to be connected to battery,replaces a stationary installation• Boiling point tester – higher testing accuracy in comparisonto other testing methods• Easy application – brake fluid remains in its fluid reservoir• Time saving – the test can be carried out directly in the fluid reservoir• Security for the user – no fluid loss (environmentally sound)• Approved by vehicle manufacturers• Approved by TÜV Austria• Dot 3 - 4 - 5.1 brake fluid• Operating voltage 12 V1 44954-1 129201Calliper Gauge for Brake DrumsMeasuring Temperatureup to 320° C (608° F)Brake Fluid:Dot 3 – 4 – 5.1SR7• For the operation of the track rod screwing• Double, spring-bearing jaw openingprevents slipping off, especially on seized or very tight screws• Forged design• Application on BMW 3 and 5-series,MERCEDES-BENZ C and E-Classes,OPEL Astra, Corsa, Kadett-E, Omega and Vectra,PEUGEOT 3/406, NISSAN, RENAULT, SEAT Ibiza,SKODA Fabia and Octavia,VW Bora, Golf I-IV, Jetta, Polo, Sharan, T4, VentoAUDI 80, 100, A4, A61 S 44950-13 13 0980334950-14 14 0980404950-17 17 0980574950-19 19 0980644950-22 22 100712• For the abrasion test at the drum brakes of passenger carsand commercial vehicles (follow vehicle manufacturer’s instructions)• Scale and slide made of aluminium profile• Jaws made of stainless steel, 150 mm long• Inside measuring with immediate reading• Vernier 1/20• With fixing screw• Measuring range up to 500 mm• In wooden box1 44955-1 073153Components and Spare Parts see pages 228 to 236 205
Page 1 and 2: Proven safetyFast and safe workingE
Page 3 and 4: Specialty ToolsChassis - Shock Abso
Page 5: Specialty ToolsChassis - Shock Abso
Page 8 and 9: Ingenious ToolsInside Spring Vice S
Page 10 and 11: Ingenious ToolsSpecialty ToolsChass
Page 14 and 15: Ingenious ToolsCalliper Gauge for B
Page 16 and 17: Ingenious ToolsTorque ToolsHAZET -
Page 18 and 19: Ingenious ToolsHAZET Torque ToolsTo
Page 20 and 21: Ingenious ToolsTorque ToolsDynamome
Page 22 and 23: Ingenious ToolsTorque Tools8Repair
Page 24 and 25: Ingenious ToolsSpecial Levers• Wi
Page 26 and 27: Ingenious ToolsInsert Adapter with
Page 28 and 29: Ingenious ToolsTorque MultipliersTo
Page 30 and 31: Ingenious ToolsPneumatic ToolsImpac
Page 32: Ingenious ToolsPneumatic ToolsAir D

HAZET – Safety Spring Vice 4900

Create successful ePaper yourself

Delete template?

Save as template?