Download Manual - Scag Power Equipment

More documents

Recommendations

Info

4321Section 62. Turn the adjusting rods counter-clockwise to lower thefront of the deck and clockwise to raise the front of thedeck. When a difference of 1/4 inch from front to rearis obtained on left and right, tighten both jam nuts.Adjusting NutJam NutBladeTape MeasureAdjusting RodFigure 6-11 Measuring Cutting Edge HeightLoosen the two jam nuts on the gauge rod (See Figure6-12). Slide the gauge rod to the proper setting on the heightgauge. Tighten the jam nuts.Figure 6-10 Adjusting Deck Pitch6.12 BLADE CUTTING HEIGHTADJUSTMENTThe blade cutting height is adjusted by actuating the deckheight switch on the instrument panel. However, if thecutting height compared to what is shown on the cuttingheight gauge (See Figure 6-12) is in question, the cuttingheight should be checked. To check the cutting height, liftthe discharge chute and measure from the ground to thecutting edge of the blade (See Figure 6-11). If themeasurement is different from what is registered on thegauge, adjust the gauge rod to the proper setting.AdjustingNutsFigure 6-12 Adjusting NutsHeightIndicator Rod2424
4012345382134132453978910111213141516179191824 3433313536 3265 1627640372464424344454647484950515241532545556565554241534159606162633257581612161258534158254555664246869 70 716867327412162823257226292422252410 201321357374MAG-61, MAG-72 CUTTER DECK44390S0111
Page 1 and 2: OPERATOR'S MANUALMAGNUM IIIMODEL MA
Page 3 and 4: Section 1GENERAL INFORMATION1.1 INT
Page 5 and 6: Section 26. Prolonged exposure to l
Page 7 and 8: Section 22.6 SAFETY AND INSTRUCTION
Page 9 and 10: Section 33.3 TRACTOR (CONT'D)Seat .
Page 11 and 12: Section 45. Temperature Gauge: Indi
Page 13 and 14: Section 44.4 DIESEL ENGINE BREAK-IN
Page 15 and 16: Section 43. Check that all systems
Page 17 and 18: Section 4-IMPORTANT-Do not wash a h
Page 19 and 20: Section 5TROUBLESHOOTING CUTTING CO
Page 21 and 22: Section 5TROUBLESHOOTINGCONDITION C
Page 23 and 24: Section 6-NOTE-If you turn the nut
Page 25: Section 66.10 BELT ALIGNMENTBelt al
Page 29 and 30: MAG-61, MAG-72 DECK SUPPORT36676970
Page 31 and 32: 44123 4 45691010111213143536151617
Page 33 and 34: ENGINE DECK1 375317 562352418173750
Page 35 and 36: RADIATOR/OIL COOLER1429272233173068
Page 37 and 38: MUFFLER AND AIR CLEANER4312 1561097
Page 39 and 40: 52123456789101112138141516273026463
Page 41 and 42: PUMP AND FAN DRIVE SYSTEMS1412878 7
Page 43 and 44: INSTRUMENT PANEL342121201929313012
Page 45 and 46: WIRING HARNESS AND ELECTRICAL COMPO
Page 47 and 48: 601234 5267981710111411131416131619
Page 49 and 50: 62PARKING BRAKE LINKAGE123456298111
Page 51 and 52: 64123475683072326273493510112918121
Page 53 and 54: FORWARD/REVERSE LINKAGE123451610132
Page 55 and 56: FUEL TANK AND LINES278 35 623292831
Page 57 and 58: HYDRAULIC CIRCUITS12243305262827251
Page 59 and 60: *DELAY MODULE TIMERCONTROL PANELRED
Page 61: GREASE FITTING LUBRICATION CHARTLUB
Page 64 and 65: TRACTOR (CONT'D)Seat ..............
Page 66: © 1996SCAG POWER EQUIPMENTDIVISION

Download Manual - Scag Power Equipment

Create successful ePaper yourself

Delete template?

Save as template?