Current Catalog - John S. Hyatt & Associates, Inc.

More documents

Recommendations

Info

JAMESENGINEERING15" TOWERSYSTEMThe Tower Lifting System is a device fitted to the sleeve block with 2 diagonal braces whichclamp on to the horizontal truss to enable the tower to be raised or lowered safely using thechain motor. The chain hoist is rigged in the lifting point and the hoist chain is passed over thelifting system pulley and then around the Roller Beam and fixed to the top of the hinge section.The tower is raised by using the chain hoist to pull up on the tower. Caution should be used tonot pull the tower over, when the tower is near vertical.PRODUCTCODEB4250B4003B4003BDESCRIPTIONTower Lifting SystemSmall Outrigger armLarge OutriggerWTlbs3819.5Outrigger arms are required when using lessthan 3 towers. These are designed to providestability and rigidity to single or 2 tower systems.74"75"The ground support tower system can be used outside but must be suitably anchored from thetop of each tower sleeve block to the ground via a guy wire to a suitable ground anchor. Werecommend that the bases are sat on top of a 3' square piece of 3/4" plywood. Should a cover berequired please refer to James Thomas Engineering for an approved design to suit yourrequirements.The ground support tower system can also be specified with lock offs which provide safetyagainst chain failure. We offer 2 types of lock offs. The first lock off is for truss systems which willalways be rigged at the top of the towers. The second type of lock off is designed to fit in thetower at the desired height, whether the truss is at the top of the tower or not.E8
JAMESENGINEERINGTOWEROUTRIGGERSThe ground support tower system is manufactured with the purpose ofproviding a lifting medium for a variety of Thomas trusses ranging from 12" x 12"through to heavy duty truss.Towers provide the necessary support for a truss rig in venues where the flyingpoints are either not strong enough, or in the right place. Towers are capable oflifting 2 ton to a maximum height of 40 feet.Outrigger and Stabilizer sets are required when using less than 3 towers. Theseare designed to provide stability and rigidity to single or two tower systems.Small Outrigger arm suitablefor all tower systemsP/N B400319.5 lbs.Large Outrigger suitable forall tower systemsP/N B4003B74"75"A tower lifting system can alsobe supplied with 12" or 15"tower system.E9
Page 4 and 5:
JAMESTABLE OF CONTENTSiiiConditions
Page 6 and 7:
JAMESENGINEERINGPAR 64LANTERNSBLACK
Page 8:
JAMESENGINEERINGPAR 64LANTERNSPRODU
Page 11 and 12:
JAMESENGINEERINGPar 56 OutdoorLante
Page 13 and 14:
JAMESENGINEERINGOUTDOOR LANTERNPROD
Page 15 and 16:
JAMESENGINEERINGPAR 56LANTERNSACCES
Page 18 and 19:
JAMESENGINEERINGACCESSORIES FOR PAR
Page 20 and 21:
JAMESENGINEERINGPAR 36LANTERNSBLACK
Page 22 and 23:
JAMESPINSPOTSENGINEERINGThomas manu
Page 24 and 25:
JAMESDESCRIPTIONPAR 16 U.S. STANDAR
Page 26 and 27: JAMESBar length 7 ft 6 insENGINEERI
Page 28 and 29: JAMESPRODUCTCODEC0401-ALC0461-ALC08
Page 30 and 31: JAMESENGINEERINGProductDESCRIPTIONC
Page 32 and 33: JAMESENGINEERINGMULTI-CABLEMULTI-CA
Page 34 and 35: JAMESGP 18 x 12ENGINEERING18" x 12"
Page 36 and 37: JAMESGP TRIANGULARENGINEERING23 1/4
Page 38 and 39: JAMESENGINEERINGGP 20.5 x 20.510 ft
Page 40 and 41: JAMESENGINEERINGHD 20 x 30Plan View
Page 42 and 43: JAMESPRE-RIG TRUSSENGINEERINGPre-Ri
Page 44 and 45: JAMESSINGLE BAR PRE-RIGENGINEERINGA
Page 47 and 48: JAMESENGINEERINGSUPERLITETRUSSThis
Page 49 and 50: JAMESENGINEERINGSUPERLITETRUSSB1602
Page 51 and 52: JAMESENGINEERINGSquarelite trussThi
Page 53 and 54: JAMESENGINEERINGSquarelite truss2 W
Page 55 and 56: JAMESENGINEERINGSUPERTRUSS18 x 12A
Page 57 and 58: JAMESENGINEERINGSUPER-TRUSS20.5 x 2
Page 59 and 60: JAMESPRE-RIGSUPERTRUSSENGINEERINGTh
Page 61: JAMESENGINEERINGMOVINGLIGHTSUPERTRU
Page 64 and 65: JAMESAllowable Load Dataempty singl
Page 66 and 67: JAMESENGINEERINGSUPERTRUSS20.5 x 30
Page 68 and 69: JAMESENGINEERING30" FOLDINGSUPERTRU
Page 70 and 71: JAMESSupermegatrussENGINEERINGSuper
Page 73 and 74: JAMESENGINEERING12" TOWERSYSTEMThe
Page 75: JAMESENGINEERING15" TOWERSYSTEMThe
Page 79 and 80: JAMESENGINEERING12 - Lite unit9 - L
Page 81 and 82: JAMESCYC-LITE UNITSENGINEERINGThe a
Page 83 and 84: JAMESENGINEERINGG0300 - Swivel coup
Page 85 and 86: JAMESENGINEERINGCM LODESTARELECTRIC
Page 87: JAMESENGINEERINGTRUSS LIFTINGPOINTS
Page 93 and 94: Never mix different makes or types
Page 95 and 96: JAMESENGINEERING®NOTES ON TRUSS IN
Page 97 and 98: DENTS AND CHEWS Damage is often cau
Page 99 and 100: 10. When rigging the chain hoist it
Page 101 and 102: 1. Place the bases on the stage wit
Page 103 and 104: 17. Finish setting up the rig. Be s
Page 105: DISASSEMBLY1. Climb each tower (wit
show all

Current Catalog - John S. Hyatt & Associates, Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?