Flowcrete standard template - Arcon Supplies

9. Physical and chemical propertiesAppearance : Liquid, colour on label pH : Not determined.Odour : slight Relative Density : ~1.56Boiling Point : >200 o C Water solubility : Practically insoluble at 20 o CFlashpoint : >200 o C Water miscibility : ImmiscibleExplosion limits : Not explosive. :10. Stability and reactivityMaterial is stable if stored under recommended storage and handling conditions.Material decomposes at high temperatures. Avoid temperatures above 40 o C.When the base is mixed with the hardener an exothermic reaction starts (i.e. heat is generated).If the mix is not applied within 20 - 30 minutes some smoking may occur.Conditions to avoid : Take precautionary measures against extremes of temperature, avoid temperatures above40 o C.Materials to avoid : Strong oxidising agents. Strong acids and strong bases.Hazardous decompositionproducts: Does not occur at recommended storage and handling conditions.Burning produces noxious and toxic fumes of carbon monoxide and carbon dioxide (CO2).11. Toxicological informationAcute oral toxicity : LD50 (rat) dose > 5,000 mg/kg (epoxy resin)LD50 (rat) = 2900 mg/kg (hexane-1,6-diol diglycidyl ether)Inhalation : May be mildly irritating. Irritating vapour can be formed when heated or during spraying.Eye irritation : Irritating (rabbit), may cause a sting.Skin Irritation : Irritating (rabbit) dermal.Sensitisation : Causes sensitisation (guinea pig) dermal – prolonged or repeated contact may result in anallergic eczema reaction each time the person is in contact with the material.12. Ecological informationEcotoxicity : Epoxy resin - EC50/72hr/algae = 9.4 mg/l.hexane-1,6-diol diglycidyl ether – LC50/fish = 10 - 100 mg/lMobility : MobilePersistence and degradability : Not readily biodegradable.Bioaccumulative potential : No data available.Additional ecologicalinformation: Toxic to aquatic organisms, may cause long-term adverse effects in the aquaticenvironment. Avoid subsoil penetration.Prevent product from entering drains, do not contaminate surface water.Flowcoat SF41 Base A H+S.doc Date printed 19 April, 2007 Page 3 of 5 Ref: CHIP300219

13. Disposal considerationsUnused Product/waste fromcleaning etc.: Must be disposed in compliance with local regulations.EC Waste Catalogue (EWC) code: 08 01 11 Waste products from the Manufacture,Formulation, Supply and Use (MFSU) of paint and varnish. Waste paint and varnishcontaining organic solvents or other dangerous substances.Unused product can be mixed with Hardener B and disposed of under EC WasteCatalogue (EWC) code: 08 01 12 (not a hazardous waste).Remove/invalidate the warning label.Contaminated packaging : If the container has been used for mixing with the Hardener, packaging can belandfilled in accordance with local regulations. Remove/invalidate the warning label.14. Transport informationIf the container has not been used for mixing with the Hardener, treat as for unusedproduct.Empty containers can be landfilled after cleaning, in accordance with local regulations.Remove/invalidate the warning label.Proper shipping name:UN No: 3082Environmentally hazardous substance, liquid, n.o.s.ADR/RIDClass : 9 Item No : 11 o cHI No : 90 Packing Group : IIIContains : Bisphenol A/F epoxy resin MW

Special provisions statement : Contains epoxy constituents. See information supplied by the manufacturer.Hazardous component(s) whichmust be listed on the label: Reaction product: bisphenol A/F – (epichlorhydrin); epoxy resin (number averagemolecular weight