APRIL 2011 - Weld-Quip

power PLASMA 3035/MINVERTER PLASMA CUTTING POWER SOURCE. HIGH FREQUENCY IGNITION.Art. 279 Specifications240V 50/60 Hz+ 15% / -20%32 A 16 A(115 V) (230 V)3.5 KVA 35%2.8 KVA 60%2.4 KVA 100%Single phase inputFuse rating (slow blow)Input powerSARC CONTROL5A ÷ 30A30A 35%25A 60%22A 100%ELECTRONIC8-12 (15) mm1/3”-1/2” (5/8”)4m (13 ft.)Current adjustment rangeDuty Cycle (10 min.40°C)According to IEC 60974.1Stepless regulationThickness on steel: Recommended- Max.-(Severance)Torch length60 lt/min - 3,5 bar Air consumptionIP 23 S13Kg175x503x400HProtection classWeightDimensions mmThe power source can be powered by motor generators of adequate power (Min. 6 KVA).279ART.279.011208DESCRIPTIONInverter plasma cutting power source. Comes with CEBORA CP40 4 m. hand torch, art. 1208 with work return lead (4 m - 10mm 2 ) with clamp.Complies with EN 61000-3-12.Inverter plasma cutting power source. Comes with CEBORA CP40 DAR torch for profile machine 6 m, art. 1207 with work returnlead (4 m - 10 mm 2 ) with clamp.Complies with EN 61000-3-12.CEBORA CP40 MAR hand torch with direct connection.4 m lenght (13 ft.).1207 CEBORA CP40 DAR torch for profile machine with direct connection. 6 m lenght (18 ft.).1207.20 CEBORA CP40 DAR torch for profile machine with direct connection. 12 m lenght (36 ft.).196Interface for use with pantographs:Start/Arc - On/Arc - Arc/Voltage.1432 Trolley for transportation of the power source only.162 Wheeled compasses for hand torch.157 Wheeled torch holder. For art.1626PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

CP 40 - Art. 1207 - 1207.20 - 1208genuine cebora plasma cutting torch HIGH FREQUENCY ignition.PatentedMARDARART. DESCRIPTION per/for Art.1208 CEBORA CP40 MAR hand torch with direct connection. 4 m. long (12 ft.). 2791207 CEBORA CP40 DAR torch for profile machine with direct connection. 6 m. long (18 ft.). 279 - 279.011207.20 CEBORA CP40 DAR torch for profile machine with direct connection. 12 m. long (36 ft.). 279 - 279.0110PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

CP 40 - Art. 1207 - 1207.20 - 1208accessories and consumablesArt. 1359Art. 1347Art. 1516 Art. 1507 Art. 1290Art. 1900ART. DESCRIPTION per/for Art.1359 Body for hand torches. 12081347 Body for torches for profile machine. 1207 - 1207.201290 ø 0,7 mm nozzles (5 pcs).1516 Electrodes (5 pcs).1507 Swirl rings (2 pcs).1900 Nozzle holder.162 Wheeled compasses for CP 40 MAR hand torch Art. 1208. 1208157 Wheeled torch holder. For art. 162. 12081207 - 1207.2012081207 - 1207.2012081207 - 1207.2012081207 - 1207.2012082011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL11

CP 101 - Art. 1220 - 1220.20genuine cebora plasma cutting torch HIGH FREQUENCY ignition.PatentedMARART. DESCRIPTION per/for Art.1220 CEBORA CP101 MAR hand torch with central adaptor. 6 m. long (18 ft.). 355 - 3591220.20 CEBORA CP101 MAR hand torch with central adaptor. 12 m. long (36 ft.). 355 - 35912PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

CP 101 - Art. 1220 - 1220.20accessories and consumablesArt. 1911Art. 1146Art. 1877 Art. 1958 Art. 1765Art. 1404ART. DESCRIPTION per/for Art.1146 Body for hand torches. 1220 - 1220.201765 ø1,2 mm nozzles (5 pcs). Can be used btw. 20 and 60 Amp. 1220 - 1220.201877 Electrodes (5 pcs). 1220 - 1220.201958 Swirl ring (2 pcs). 1220 - 1220.201911 Nozzle holder. 1220 - 1220.201404 Spacing bushes with 2 points (3 pcs) 1220 - 1220.20163 Wheeled compasses for CP101 MAR hand torches art. 1220. 1220 - 1220.20153 Wheeled torch holder for CP101 MAR hand torches art. 1220. 1220 - 1220.202011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL13

CP 161 - Art. 1229-1230-1230.20-1231-1231.20genuine cebora plasma cutting torch HIGH FREQUENCY ignition.PatentPendingMARDAR1229ART. DESCRIPTION per/for Art.CEBORA CP161 DAR torch for profile machine with central adaptor.4 mt. long (12 ft.). Shielded.For HV 14 unit (art. 481).To be compulsorily coupled with Art. 108.1230 CEBORA CP161 MAR hand torch with central adaptor. 6 m. long (18 ft.).1230.20 CEBORA CP161 MAR hand torch with central adaptor. 12 m. long (36 ft.).12311231.20CEBORA CP161 DAR torch for profile machine with central adaptor.6 m. long (18 ft.). Shielded.CEBORA CP161 DAR torch for profile machine with central adaptor.12 m. long (36 ft.). Shielded.957357 - 361 - 946952 - 956 - 957357 - 361 - 946952 - 956 - 957355-357-359-361 .(A) *952 ...................... (B) *957 ...................... (C) *946 - 956355-357-359-361 .(A) *952 ...................... (B) *957 ...................... (C) *946 - 956* To be compulsorily coupled with interface:(A) Art. 196 for Art. 355-357-359-361(B) Art. 197 for Art. 952(C) Art. 108 for Art. 95714PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

CP 161 MAR - Art. 1230 - 1230.20accessories and consumables for manual cuttingShieldNozzle Swirl ring Electrode Spacer Nozzle holder Torch body Handle60 AArt. 1760100 AArt. 1620Art. 1398Art. 1761Art. 1619120 AArt. 1988Art. 1970 Art. 1876Art. 1904 Art. 1144Art. 1762160 AArt. 1701Art. 1763Art. 1941ART. DESCRIPTION per/for Art.1144 Body for hand torches. 1230 - 1230.201941 Handle assy 1230 - 1230.201398 "O-Rings" (5 pcs) 1230 - 1230.201760176117621763ø1.2 mm nozzles (5 pcs).Can be used btw. 20 and 60 Amp.ø1.4 mm nozzles (5 pcs).Can be used btw. 60 and 100 Amp.ø1.6 mm nozzles (5 pcs).Can be used btw. 100 and 120 Amp.ø1.8 mm nozzles (5 pcs).Can be used btw. 120 and 160 Amp.1230 - 1230.201230 - 1230.201230 - 1230.201230 - 1230.201988 Shield. 1230 - 1230.201876Electrodes (5 pcs).Can be used btw. 20 and 160 Amp.1230 - 1230.201904 Nozzle holder. 1230 - 1230.201970 Swirl-Ring. 1230 - 1230.201619 Brass cooling pipe (5 pcs) 1230 - 1230.201620 Spacing springs (5 pcs) 1230 - 1230.201701 Spacing bushes with 2 points (3 pcs) 1230 - 1230.20407 Wheeled compasses for hand torches. 1230 - 1230.20406 Wheeled torch holder. 1230 - 1230.202011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL15

CP 161 MAR - Art. 1230 - 1230.20accessories and consumables for contact cuttingNozzle Swirl ring Electrode Nozzle holder Torch body HandleArt. 139845 AArt. 1619Art. 1760Art. 1970 Art. 1876 Art. 1904 Art. 1144Art. 1941ART. DESCRIPTION per/for Art.1144 Body for hand torches. 1230 - 1230.201941 Handle assy 1230 - 1230.201398 "O-Rings" (5 pcs) 1230 - 1230.2017601876ø1.2 mm nozzles (5 pcs).Can be used btw. 20 and 45 Amp.Electrodes (5 pcs).Can be used btw. 20 and 160 Amp.1230 - 1230.201230 - 1230.201904 Nozzle holder. 1230 - 1230.201970 Swirl-Ring. 1230 - 1230.201619 Brass cooling pipe (5 pcs) 1230 - 1230.2016PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

CP 161 MAR - Art. 1230 - 1230.20accessories and consumables for gougingShieldNozzle Swirl ring Electrode Nozzle holder Torch body HandleArt. 139860/120 AArt. 1619Art. 1988Art. 1764Art. 1970 Art. 1876 Art. 1904 Art. 1144Art. 1941ART. DESCRIPTION per/for Art.1144 Body for hand torches. 1230 - 1230.201941 Handle assy 1230 - 1230.201398 "O-Rings" (5 pcs) 1230 - 1230.20ø3 mm nozzles (5 pcs).17641230 - 1230.20For gouging.1988 Shield. 1230 - 1230.20Electrodes (5 pcs).18761230 - 1230.20Can be used btw. 20 and 160 Amp.1904 Nozzle holder. 1230 - 1230.201970 Swirl-Ring. 1230 - 1230.201619 Brass cooling pipe (5 pcs) 1230 - 1230.202011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL17

CP 161 DAR - Art. 1229 - 1231 - 1231.20accessories and consumables for automated cuttingShieldNozzle Swirl ring Electrode Nozzle holder Torch body60 AArt. 1760Art. 1619Art. 1398100 AArt. 1761120 AArt. 1989Art. 1970 Art. 1876 Art. 1904 Art. 1145Art. 1762160 AArt. 1763ART. DESCRIPTION per/for Art.1145 Body for torches for profile machine.1398 "O-Rings" (5 pcs)17601761176217631989 Shield.1876ø1.2 mm nozzles (5 pcs).Can be used btw. 20 and 60 Amp.ø1.4 mm nozzles (5 pcs).Can be used btw. 60 and 100 Amp.ø1.6 mm nozzles (5 pcs).Can be used btw. 100 and 120 Amp.ø1.8 mm nozzles (5 pcs).Can be used btw. 120 and 160 Amp.Electrodes (5 pcs).Can be used btw. 20 and 160 Amp.1904 Nozzle holder.1970 Swirl-Ring.1619 Brass cooling pipe (5 pcs)1229 - 12311231.201229 - 12311231.201229 - 12311231.201229 - 12311231.201229 - 12311231.201229 - 12311231.201229 - 12311231.201229 - 12311231.201229 - 12311231.201229 - 12311231.201229 - 12311231.2018PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

P 70 - Art. 1573-1573.20-1566-1566.20-1564-1563accessories and consumablesPatentedArt. 1351Art. 5710171Art. 1510Art. 1402 Art. 1368Art. 1396Art. 1308Art. 1395 Art. 1394ART. DESCRIPTION per/for Art.1351* Body for hand torches. 1564 - 15731356** Handgrip with push button. 1564 - 157314021396**130813681395**Electrodes (5 pcs).Can be used btw. 15 and 70 Amp.ø1,0 mm “long life” nozzles (5 pcs).Can be used btw. 30 and 50 Amp.ø1,2 mm nozzles (5 pcs).Can be used btw. 45 and 70 Amp.Long electrodes (5 pcs).Can be used btw. 20 and 90 Amp.ø1,0 mm “long life” long nozzles (5 pcs).Can be used btw. 30 and 50 Amp.1510** Swirl ring (2 pcs).5710171 Nozzle holder.1563 - 15641573 - 15661563 - 15641573 - 15661563 - 15641573 - 15661563 - 15641573 - 15661563 - 15641573 - 15661563 - 15641573 - 15661563 - 15641573 - 15661394 Spacing springs (5 pcs) 1564 - 1573* This torch body (head) can replace the body art. 1352-P50** These parts can also be used with CEBORA P50 TORCHES2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL19

CP 95 C - Art. 1212genuine cebora plasma cutting torch. without HIGH FREQUENCY ignition.PatentedMARART. DESCRIPTION per/for Art.1212 CEBORA CP95 C MAR hand torch with direct connection. 6 m. long (18 ft.). 96120PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

CP 95 C - Art. 1212accessories and consumablesPatentedArt. 1346Art. 1513Art. 1388Art. 1851Art. 1907ART. DESCRIPTION per/for Art.1346 Body for hand torches. 121213881851Electrodes (5 pcs).Can be used btw. 15 and 50 Amp.ø1,1 mm long nozzles (10 pcs).Can be used btw. 0 and 50 Amp.121212121513 Swirl rings (2 pcs). 12121907 Nozzle holder. 1212163 Wheeled compasses for CP95 MAR hand torches art. 1212. 1212153 Wheeled torch holder for CP95 MAR hand torches art. 1212. 12122011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL21

CP 91 - Art. 1214 - 1214.20 - 1215CP 90 - 1218.50 -1218.90genuine cebora plasma cutting torch HIGH FREQUENCY ignition.PatentedMARDARART. DESCRIPTION per/for Art.1214 CEBORA CP91 MAR hand torch with central adaptor. 6 mt. length (18 ft.). 9471214.20 CEBORA CP91 MAR hand torch with central adaptor. 12 mt. length (36 ft.). 9471215 CEBORA CP91 MAR hand torch with direct connection 6 m. long (18 ft.) 9651218.50 CEBORA CP90 DAR torch for profile machine with central adaptor. 6 mt. length (18 ft.). Shielded. 9471218.90 CEBORA CP90 DAR torch for profile machine with central adaptor. 12 mt. length (36 ft.). Shielded. 94722PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

CP 91 - Art. 1214 - 1214.20 - 1215CP 90 - 1218.50 -1218.90accessories and consumablesArt. 1358Art. 1510Art. 1907Art. 1348Art. 1368Art. 1847-1848-1849Art. 1404ART. DESCRIPTION per/for Art.1358 Body for hand torches. 1214-1214.20-12151348 Body for torches for profile machine. 1218.50-1218.901847 ø1 mm long nozzles (10 pcs). For contact cutting. Can be used btw. 20 and 50 Amp. 1214-1214.20-1215184818491368ø1,2 mm long nozzles (10 pcs).Can be used btw. 45 and 70 Amp.ø1,3 mm long nozzles (10 pcs).Can be used btw. 45 and 90 Amp.Long electrodes (5 pcs).Can be used btw. 20 and 90 Amp.1510 Swirl rings (2 pcs).1907 Nozzle holder with protection.1214-1214.20-12151218.50-1218.901214-1214.20-12151218.50-1218.901214-1214.20-12151218.50-1218.901214-1214.20-12151218.50-1218.901214-1214.20-12151218.50-1218.901404 Spacing bushes with 2 points (3 pcs) 1214-1214.20-1215163 Wheeled compasses for CP91 MAR hand torches. 1214-1214.20-1215153 Wheeled torch holder for CP91 MAR hand torches. 1214-1214.20-12152011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL23

CP 160 - Art. 1226-1226.20 -1228-1228.20accessories and consumablesPatentedArt. 1353Art. 1398Art. 1509Art. 1902Art. 1398Art. 1378Art. 1377Art. 1354Art. 1376Art. 1372-1373-1374Art. 1408Art. 1386ART. DESCRIPTION per/for Art.1353 Body for hand torches. 12261354 Body for torches for profile machine. 12281398 “O-Rings” (5 pcs). 1353 - 13541372137313741376ø1,3 mm nozzles (5 pcs).Can be used btw. 40 and 90 Amp.ø1,6 mm nozzles (5 pcs).Can be used btw. 80 and 120 Amp.ø1,8 mm nozzles (5 pcs).Can be used btw. 110 and 150 Amp.Electrodes (5 pcs).Can be used btw. 20 and 150 Amp.1226 - 12281226 - 12281226 - 12281226 - 12281902* Nozzle holder suitable for gouging too. 1226 - 12281377 Swirl ring. 1226 - 12281509 Extractor for Swirl-Ring. 13771378 Brass diffusers (5 pcs). 1226 - 12281386 Spacing springs (5 pcs). 12261408 Spacing bushes with 2 points (3 pcs) 1226169 Wheeled compasses for CP160 MAR hand torches. 1226155 Wheeled torch holder for CP160 MAR hand torches. 1226* Absolutely interchangeablewith art.1389.26PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

power tig 1640 DC-HFINVERTER MMA AND D.C. TIG WELDING POWER SOURCE. HF IGNITION.Art. 264 SpecificationsTIGMMAS240V 50/60 Hz+ 15% / -20%Single phase input16 A Fuse rating (slow blow)3.4 KVA 40%2.7 KVA 60%2.2 KVA 100%4.6 KVA 30%3.5 KVA 60%2.8 KVA 100%Input power5A ÷ 160A 10A ÷ 140A Current adjustment range160A 40%135A 60%110A 100%IP 23 S140A 30%115A 60%95A 100%Duty Cycle (10 min.40°C)According to IEC 60974.1Protection class10.3 Kg Weight171x420x340HDimensions mmThe power source can be powered by motor generators of adequate power (Min. 6 KVA).264ART.DESCRIPTIONInverter MMA and D.C. TIG welding power source with built-in HF ignition. Comes without welding torch and cables.Complies with EN 61000-3-12.1262 BINZEL “ABITIG 200” Up/Down torch (200 A - 35%) 4 m. length.1260 BINZEL “ABITIG 200” torch (200 A-35%) 4 m. length.1432 Trolley for transportation of the power source only.187 Remote control unit for welding current adjustment.1192 5 m. extension cable for remote control unit art. 187.193Foot control unit for welding current adjustment.Equipped with 5 m. cable and ON/OFF switch.1180 Adapter to simultaneously attach the torch and the foot control unit.1451 2 gauge flowmeter.2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL27

tig sound dc 3241/tINVERTER multivoltage MMA AND pulse D.C. TIG WELDING POWER SOURCE. HF IGNITION.Art. 362 SpecificationsTIGMMAS415V 50/60 Hz±10%Three phase input16 A 16 A Fuse rating (slow blow)9.6 KVA 40%7.8 KVA 60%6.6 KVA 100%11.5 KVA 40%9.3 KVA 60%7.8 KVA 100%Input power5A ÷ 320A 10A ÷ 280A Current adjustment range320A 40%280A 60%250A 100%280A 40%240A 60%210A 100%Duty Cycle, (10 min.40°C)according to IEC 60974.1IP 23 SProtection class79.5 KgWeight705x1060x975HDimensions mm362ART.DESCRIPTIONInverter multi-voltage MMA and pulse D.C. TIG welding power source with built in HF ignition.Comes with cooling unit and trolley for transportation of the power source.Without torch and welding cables.Complies with EN 61000-3-12.1256 BINZEL “ABITIG 450 W” water cooled torch (450 Amp.) - 4 m. length.1258 BINZEL “ABITIG 450 W UP/DOWN” Water cooled torch (450 Amp.) - 4 m. length.187 Remote control unit for welding current adjustment.1192 5 m. extension cable for remote control unit art. 187.193Foot control unit for welding current adjustment.Equipped with 5 m. cable and ON/OFF switch.1180 Adapter to simultaneously attach the torch and the foot control unit.Accessories set for electrode welding:electrode holder (4 m. -16mm 2 ),work return lead (4 m - 16 mm2)1451 2 gauge flowmeter.30PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

tig sound ac-dc 1531/mINVERTER MMA AND pulse a.c.-D.C. TIG WELDING POWER SOURCE. HF IGNITION.Art. 364 SpecificationsTIGMMAS240V 50/60 Hz+ 15% / -20%Single phase input16 A Fuse rating (slow blow)3.9 KVA 30%2.5 KVA 60%2.2 KVA 100%4.4 KVA 30%3.3 KVA 60%3.0 KVA 100%Input power5A ÷ 150A 10A ÷ 130A Current adjustment range150A 30%110A 60%100A 100%IP 23 S130A 30%100A 60%90A 100%Duty Cycle, (10 min.40°C)according to IEC 60974.1Protection class17.6 Kg Weight207x500x411HDimensions mmThe power source can be powered by motor generators of adequate power (Min. 6 KVA).364ART.DESCRIPTIONInverter MMA and pulse A.C.-D.C. TIG welding power source with built-in HF ignition.Comes without welding torch and cables.Complies with EN 61000-3-12.1262 BINZEL “ABITIG 200” Up/Down torch (200 A - 35%) 4 m. length.1260 BINZEL “ABITIG 200” torch (200 A-35%) 4 m. length.1432 Trolley for transportation of the power source only.187 Remote control unit for welding current adjustment.1192 5 m. extension cable for remote control unit art. 187.193Foot control unit for welding current adjustment.Equipped with 5 m. cable and ON/OFF switch.1180 Adapter to simultaneously attach the torch and the foot control unit.1451 2 gauge flowmeter.2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL31

tig sound ac-dc 3341/T synergicsynergic INVERTER MMA AND pulse a.c./D.C. TIG WELDING poweR source. HF IGNITION.Art. 367 SpecificationsTIGMMAS415V 50/60 Hz± 10%Three phase input20 A Fuse rating (slow blow)10.4 KVA 40% 14.5 KVA 40%10.1 KVA 60% 14.0 KVA 60% Input power9.7 KVA 100% 13.5 KVA 100%5A ÷ 330A 10A ÷ 330A Current adjustment range330A40% 330A40%Duty Cycle, (10 min.40°C)320A60% 320A60%according to IEC 60974.1310A100% 310A100%IP 23 SProtection class93 Kg Weight705x1060x975HDimensions mm367ART.DESCRIPTIONSynergic inverter MMA and pulse A.C.-D.C. TIG welding power source with built-in HF ignition. Comes with cooling unit andtrolley for transportation of the power source.Without torch and welding cables.Complies with EN 61000-3-12.1256 BINZEL “ABITIG 450 W” water cooled torch (450 Amp.) - 4 m. length.1258 BINZEL “ABITIG 450 W UP/DOWN” water cooled torch (450 Amp.) - 4m length.187 Remote control unit for welding current adjustment.1192 5 m. extension cable for remote control unit art. 187.193Foot control unit for welding current adjustment.Equipped with 5 m. cable and ON/OFF switch.1180 Adapter to simultaneously attach the torch and the foot control unit.EARTH4m Earth lead.1451 2 gauge flowmeter.34PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

tig sound ac-dc 4561/T synergicsynergic INVERTER MMA AND pulse a.c./D.C. TIG WELDING poweR source. HF IGNITION.Art. 368 SpecificationsTIGMMAS415V 50/60 Hz± 10%Three phase input25 A Fuse rating (slow blow)16.0 KVA 60%12.5 KVA 100%15.8 KVA 60%13.5 KVA 100%Input power5A ÷ 450A 10A ÷ 360A Current adjustment range450A 60%380A 100%IP 23 S360A 60%320A 100%Duty Cycle, (10 min.40°C)according to IEC 60974.1Protection class136 Kg Weight705x1060x1155HDimensions mm368ART.DESCRIPTIONSynergic inverter MMA and pulse A.C.-D.C. TIG welding power source with built-in HF ignition. Comes with cooling unit andtrolley for transportation of the power source.Without torch and welding cables.Complies with EN 61000-3-12.1256 BINZEL “ABITIG 450 W” water cooled torch (450 Amp.) - 4 m. length.1258 BINZEL “ABITIG 450 W UP/DOWN” water cooled torch (450 Amp.) - 4m length.187 Remote control unit for welding current adjustment.1192 5 m. extension cable for remote control unit art. 187.193Foot control unit for welding current adjustment.Equipped with 5 m. cable and ON/OFF switch.1180 Adapter to simultaneously attach the torch and the foot control unit.EARTH4m Earth lead.1451 2 gauge flowmeter.2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL35

tig torchesArt.1256 Art.1258 Art.1259 Art.1260Art.1262 Art.1277 Art.1567.01 Art.1637ART. DESCRIPTION per/for Art.1256 BINZEL “ABITIG 450 W” Water cooled torch (450 Amp) 4 m. length.1258 BINZEL “ABITIG 450 W” Up/Down. Water cooled torch (450 Amp). 4 m. length.1259 BINZEL “ABITIG 200” torch (200A - 35%) - 4 m long. “Euro” type connection.1260 BINZEL “ABITIG 200” torch (200A - 35%) 4 m. long.1262 BINZEL “ABITIG 200” Up/Down torch (200A - 35%) 4 m. long.309-360-362-365366-366.05-367367.05-368-368.05309-360-362-365366-366.05-367367.05-368-368.05387-387.05389-389.05264-265-360364-365264-265-360364-3651277 3 m “CEBORA SR17” TIG welding torch. With control push-button for gas and power. 283-283.111567.01 “CEBORA T 150” torch 4 m. long. 256-2571637 3 m “CEBORA” TIG welding torch. With control push-button for gas and power. 298-298.1136PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

power rod 131MMA AND TIG INVERTER TYPE D.C. WELDING POWER SOURCE. CEBORA LIFT IGNITION.Art. 256 Specifications240V 50/60 Hz+ 15% / -20%Single phase inputS16 A Fuse rating (slow blow)4.0 KVA 30%3.3 KVA 60%3.0 KVA 100%10A ÷ 130A130A 30%110A 60%100A 100%Ø 1.5 ÷ 3.2IP 23 SInput powerCurrent adjustment rangeDuty Cycle, (10 min.40°C)according to IEC 60974.1Electrodes that can be usedProtection class4.5 Kg Weight160x302x292HDimensions mmThe power source can be powered by motor generators of adequate power (Min. 6 KVA).2561281ART.DESCRIPTIONMMA and TIG inverter type D.C. welding power source. Cebora lift ignition. Antishock plastic housing with shoulder strap.Comes without torch and welding cables.Complies with EN 61000-3-12.Accessories set for electrode welding:electrode holder (4 m. -16mm 2 ),work return lead (4 m - 16 mm 2 )1567.01 “CEBORA T 150” torch 4 m. length.2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL37

power rod 1535MMA AND TIG INVERTER TYPE D.C. WELDING POWER SOURCE. CEBORA LIFT IGNITION.Art. 257 Specifications240V 50/60 Hz+ 15% / -20%Single phase inputS16 A Fuse rating (slow blow)4.8 KVA 35%3.9 KVA 60%3.5 KVA 100%5A ÷ 150A150A 35%125A 60%115A 100%Ø 1.5 ÷ 4.0IP 23 SInput powerCurrent adjustment rangeDuty Cycle, (10 min.40°C)according to IEC 60974.1Electrodes that can be usedProtection class9.2 Kg Weight172x420x340HDimensions mmThe power source can be powered by motor generators of adequate power (Min. 6 KVA).2571281ART.DESCRIPTIONMMA and TIG inverter type D.C. welding power source Cebora lift ignition.Comes without torch and welding cables.Complies with EN 61000-3-12.Accessories set for electrode welding:electrode holder (4 m. -16mm 2 ),work return lead (4 m - 16 mm 2 )1567.01 “CEBORA T 150” torch 4 m. length.38PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

power rod 1840MMA AND TIG INVERTER TYPE D.C. WELDING POWER SOURCE. CEBORA LIFT IGNITION.Art. 261 Specifications240V 50/60 Hz+ 15% / -20%Single phase inputS16 A Fuse rating (slow blow)6.0 KVA 40%4.7 KVA 60%3.6 KVA 100%10A ÷ 180A180A 40%150A 60%120A 100%Ø 1.5 ÷ 4.0IP 23 SInput powerCurrent adjustment rangeDuty Cycle, (10 min.40°C)according to IEC 60974.1Electrodes that can be usedProtection class9.5 Kg Weight172x420x340HDimensions mmThe power source can be powered by motor generators of adequate power (Min. 8 KVA).2611281ART.DESCRIPTIONMMA and TIG inverter type D.C. welding power source. Cebora lift ignition.Comes without welding torch and cablesComplies with EN 61000-3-12.Accessories set for electrode welding:electrode holder (4 m. -16mm 2 ),work return lead (4 m - 16 mm2)187 Remote control unit for MMA welding current adjustment.1327 5 m. extension cable for remote control art. 187.181 Foot control unit for welding current adjustment. Equipped with 5 m. cable and ON/OFF switch.1180 Adapter to simultaneously attach the torch and the foot control unit.2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL39

sound mma 2336/Tmma and tig INVERTER type d.c. WELDING POWER SOURCE. CEBORA LIFT IGNITION.Art. 328 Specifications415V 50/60 Hz± 10%Three phase inputS10 A Fuse rating (slow blow)8.3 KVA 35%6.9 KVA 60%6.0 KVA 100%10A ÷ 230A230A 35%210A 60%190A 100%Ø 1.5 ÷ 4.0IP 23 SInput powerCurrent adjustment rangeDuty Cycle, (10 min.40°C)according to IEC 60974.1Electrodes that can be usedProtection class15.7 Kg Weight207x437x411HDimensions mmThe power source can be powered by motor generators.3281281ART.DESCRIPTIONMMA and TIG inverter type D.C. welding power source. Cebora lift ignition.Comes without welding torch and cablesComplies with EN 61000-3-12.Accessories set for electrode welding:electrode holder (4 m. -16mm 2 ),work return lead (4 m - 16 mm2)187 Remote control unit for MMA welding current adjustment.1192 5 m. extension cable for remote control art. 187.181 Foot control unit for welding current adjustment. Equipped with 5 m. cable and ON/OFF switch.1432 Trolley for transportation of the power source only.40PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

Sound mma 3536/T Cellmma and tig INVERTER type d.c. WELDING POWER SOURCE. CEBORA LIFT IGNITION.Art. 335 Specifications415V 50/60 Hz± 10%Three phase inputS16 A Fuse rating (slow blow)14.4 KVA 35%10.0 KVA 60%8.0 KVA 100%10A ÷ 350A350A 35%270A 60%230A 100%Ø 1.5 ÷ 6.0IP 23 SInput powerCurrent adjustment rangeDuty Cycle, (10 min.40°C)according to IEC 60974.1Electrodes that can be usedProtection class26.3 Kg Weight297x463x588HDimensions mmSUITABLE FOR CELLULOSIC COATED ELECTRODES.The power source can be powered by motor generators.335ART.DESCRIPTIONMMA and TIG inverter type D.C. welding power source. Cebora lift ignition.Comes without welding torch and cablesComplies with EN 61000-3-12.1286.05 4m Earth lead.187 Remote control unit for MMA welding current adjustment.1192 5 m. extension cable for remote control unit art. 187.181 Foot control unit for welding current adjustment. Equipped with 5 m cable and ON/OFF switch.1432 Trolley for transportation of the power source only.2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL41

gas/no gas MIG-MAG SYNERGIC WELDING MACHINE.evo 200 M synergic combiArt. 622 Specifications240V 50/60 Hz± 10%Single phase inputS25 A Fuse rating (slow blow)7.8 KVA 20%3.3 KVA 60%2.5 KVA 100%25A ÷ 230A180A 20%105A 60%80A 100%Input powerMin.-max. current that can be obtained in weldingDuty Cycle, (10 min.40°C)according to IEC 60974.12x60.6/0.8/0.9 Fe0.6/0.8/0.9/1.0 Al0.8/0.9 Inox0.9 Cored0.8/0.9 Cu-Si 3%Ø 300 mm/15 KgNumber of regulation stepsWire sizes that can be usedMax. wire spool sizeIP 21 SProtection class58 Kg Weight515x820x660HDimensions mmOne programmable control circuit board only for all the EVO Synergic models.622ART.DESCRIPTIONCompact single-phase synergic MIG-MAG and flux cored wire welding machine with 2-roll wire feeder in aluminium, digital controlpanel with ammeter and stored synergic curves (aluminium, mild and stainless steel), post-gas, soft start adjustment, spot/stitchwelding time and burn back adjustment. Comes with work return lead (3,5 m - 25 mm 2 ) and clamp.Without torch and flowmeter.Complies with EN 61000-3-12.2003 4m (12 ft.) CEBORA PULL 2003, UP-DOWN torch.1562 Spool Gun for 750 gr. Fe or 500 gr. Al wire spools. (DIN 8559)1196 6 m. extension between art.1562 Spool Gun and power source.1196.20 12 m. extension between art.1562 Spool Gun and power source.1242 CEBORA 280 A torch - 3,5 m long. EURO type connection.1451 2 gauge flowmeter.136 Updating kit for software and synergic programmes.1933Aluminium welding kit consisting of:4,3 m. wire liner assy for 1,0-1,2 mm wire and wire guide pipe (for torch Art. 1242).1920 Arm + liner kit for 2-roller wire feeder, for Cu-Si 3% wire welding.42PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

evo 200 T synergicMIG-MAG SYNERGIC WELDING MACHINE and gma brazing machine.Art. 627 Specifications415V 50/60 Hz± 10%16 A 10 A(230 V) (400 V)6.9 KVA 30%4.2 KVA 60%3.2 KVA 100%Three phase inputFuse rating (slow blow)Input powerS18A ÷ 240A190A 30%135A 60%105A 100%Min.-max. current that can be obtained in weldingDuty Cycle. (10 min.40°C)according to IEC 60974.12x60.6/0.8/0.9/1.0 Fe0.6/0.8/0.9/1.0/1.2 Al0.8/0.9/1.0 Inox0.8/0.9/1.0 Cu-Si 3%Ø 300 mm/15 KgNumber of regulation stepsWire sizes that can be usedMax. wire spool sizeIP 21 SProtection class62 Kg Weight515x820x660HDimensions mmOne programmable control circuit board only for all the EVO Synergic models.627ART.DESCRIPTIONCompact three-phase synergic MIG-MAG welding machine with 2-roll wire feeder in aluminium, digital control panel withammeter and stored synergic curves (aluminium, mild, stainless steel and galvanized sheet gma brazing), post-gas, softstart adjustment, spot/stitch welding time and burn back adjustment. Comes with work return lead (3,5 m - 25 mm 2 ) andclamp. With spot welding timer.Without torch and flowmeter.Complies with EN 61000-3-12.2003 4m (12 ft.) CEBORA PULL 2003, UP-DOWN torch.1562 Spool Gun for 750 gr. Fe or 500 gr. Al wire spools. (DIN 8559)1196 6 m. extension between art.1562 Spool Gun and power source.1196.20 12 m. extension between art.1562 Spool Gun and power source.1242 CEBORA 280 A torch - 3,5 m long. EURO type connection.1451 2 gauge flowmeter.136 Updating kit for software and synergic programmes.1933Aluminium welding kit consisting of:4,3 m. wire liner assy for 1,0-1,2 mm wire and wire guide pipe (for torch Art. 1242).1920 Arm + liner kit for 2-roller wire feeder, for Cu-Si 3% wire welding.2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL43

MIG-MAG SYNERGIC WELDING MACHINE.evo 350 TC synergicArt. 641 Specifications415V 50/60 Hz± 10%40 A 25 A(230 V) (400 V)15.9 KVA 40%10.7 KVA 60%7.6 KVA 100%Three phase inputFuse rating (slow blow)Potenza assorbitaInput powerS35A ÷ 400A350A 40%290A 60%220A 100%2x80.6/0.8/0.9/1.0/1.2 Fe0.6/0.8/0.9/1.0/1.2 Al0.6/0.8/0.9/1.0/1.2 Inox0.9 Cu-Si 3%Ø 300 mm/15 KgIP 21 SMin.-max. current that can be obtained in weldingDuty Cycle, (10 min.40°C)according to IEC 60974.1Number of regulation stepsWire sizes that can be usedMax. wire spool sizeProtection class95 Kg Weight542x915x795HDimensions mmOne programmable control circuit board only for all the EVO Synergic models.641ART.DESCRIPTIONCompact three-phase synergic MIG-MAG welding machine with 4-roll wire feeder in aluminium, digital control panel with ammeterand stored synergic curves (aluminium, mild and stainless steel), post-gas, soft start adjustment, spot/stitch welding timeand burn back adjustment. Comes with work return lead (3,5 m - 35 mm 2 ) and clamp.Without torch and flowmeter.Complies with EN 61000-3-12.2003 4m (12 ft.) CEBORA PULL 2003, UP-DOWN torch.1239 CEBORA 380 A torch - 3,5 m long. EURO type connection.1562 Spool Gun for 750 gr. Fe or 500 gr. Al wire spools. (DIN 8559)1196 6 m. extension between art.1562 Spool Gun and power source.1196.20 12 m. extension between art.1562 Spool Gun and power source.1451 2 gauge flowmeter.136 Updating kit for software and synergic programmes.1929Aluminium welding kit consisting of:3,5 m. wire liner assy for 1,0-1,2 mm wire and wire guide pipe (for torch Art. 1239).44PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

MIG-MAG SYNERGIC WELDING MACHINE.evo 350 TS synergicArt. 643 Specifications415V 50/60 Hz± 10%Three phase inputS40 A 25 A(230 V) (400 V)15.9 KVA 40%10.7 KVA 60%7.6 KVA 100%35A ÷ 400A350A 40%290A 60%220A 100%2x80.6/0.8/0.9/1.0/1.2 Fe0.6/0.8/0.9/1.0/1.2 Al0.6/0.8/0.9/1.0/1.2 Inox0.9 Cu-Si 3%Ø 300 mm/15 KgFuse rating (slow blow)Input powerMin.-max. current that can be obtained in weldingDuty Cycle, (10 min.40°C)according to IEC 60974.1Number of regulation stepsWire sizes that can be usedMax. wire spool sizeIP 21 SProtection class90 Kg Weight615x975x900HDimensions mmOne programmable control circuit board only for all the EVO Synergic models.ART.64316521662DESCRIPTIONSynergic three phase power source for MIG-MAG welding. Comes with work return lead (3,5 m - 35mm 2 ) and clamp.Without torch, wire feed unit and extension lead.Complies with EN 61000-3-12.TDA2 wire feed unit with Cebora 2-roller wire feed block in aluminium, digital control panel with ammeter/voltmeter, storedsynergic curves (aluminium, mild steel, stainless steel), post-gas adjustment, soft start, spot/stitch welding time, wire test,2/4times, ready for water cooled torch.TD4-HD wire feed unit as above, but with Cebora 4-roller Ø 40 wire feed block in aluminium. Fitted with interface for CEBORAPUSH-PULL art. 20101239 “CEBORA 380 A” torch 3,5 m. long.1241 “CEBORA 380 A” water cooled torch 3,5 m. long.20106m (20 ft) Cebora push-pull, Up/Down water cooled torch. (350Amp. - 60%).To be used together with cooling unit Art. 1680and TD4-HD wire feed unit Art. 1662.1182 95 mm 2 -5 m. extension lead between power source and wire feeder.1182.20 95 mm 2 -10 m. extension lead between power source and wire feeder.1680 GRV8 Torch cooling unit.1451 2 gauge flowmeter.136 Updating kit for software and synergic programmes.19291930Aluminium welding kit consisting of: 3,5 m. wire liner assy for 1,0-1,2 mm wire and wire guide pipe.(for torches item 1239-1241).3,5 m. wire liner assy for 1,2-1,6 mm Al wire.(for torches item 1239-1241).2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL45

MIG-MAG SYNERGIC WELDING MACHINE.evo 450 TS synergicArt. 647 Specifications415V 50/60 Hz± 10%Three phase inputS50 A 32 A(230 V) (400 V)23.5 KVA 40%16.6 KVA 60%11.8 KVA 100%40A ÷ 500A450A 40%370A 60%290A 100%4x8Fuse rating (slow blow)Input powerMin.-max. current that can be obtained in weldingDuty Cycle, (10 min.40°C)according to IEC 60974.1Number of regulation steps0.8/0.9/1.0/1.2/1.6 Fe1.0/1.2/1.6 Al0.8/0.9/1.0/1.2 Inox1.2 CoredWire sizes that can be usedØ 300 mm/15 KgMax. wire spool sizeIP 21 SProtection class125 Kg Weight615x975x900HDimensions mmOne programmable control circuit board only for all the EVO Synergic models.ART. DESCRIPTIONSynergic three phase power source for MIG-MAG welding. Comes with work return lead (3,5 m - 95mm 2 ) and clamp.647 Without torch, wire feed unit and extension lead.Complies with EN 61000-3-12.TDA2 wire feed unit with Cebora 2-roller wire feed block in aluminium, digital control panel with ammeter/voltmeter, stored1652 synergic curves (aluminium, mild steel, stainless steel), post-gas adjustment, soft start, spot/stitch welding time, wire test,2/4times, ready for water cooled torch.1662TD4-HD wire feed unit as above, but with Cebora 4-roller Ø 40 wire feed block in aluminium. Fitted with interface for CEBORAPUSH-PULL art. 20101239 “CEBORA 380 A” torch 3,5 m. long.1241 “CEBORA 380 A” water cooled torch 3,5 m. long.1243 “CEBORA 500 A” water cooled torch 3,5 m. long.6m (20 ft) Cebora push-pull, Up/Down water cooled torch. (350Amp. - 60%).To be used together with cooling unit Art. 16802010and TD4-HD wire feed unit Art. 1662.1182 95 mm 2 -5 m. extension lead between power source and wire feeder.1182.20 95 mm 2 -10 m. extension lead between power source and wire feeder.1680 GRV8 Torch cooling unit.1451 2 gauge flowmeter.136 Updating kit for software and synergic programmes.1929Aluminium welding kit consisting of: 3,5 m. wire liner assy for 1,0-1,2 mm wire and wire guide pipe.(for torches item 1239-1241-1243).19303,5 m. wire liner assy for 1,2-1,6 mm Al wire.(for torches item 1239-1241-1243).46PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

tri star mig 1636/mINVERTER multiprocess power source for mig/mag, DC tig and mma welding.Art. 298 SpecificationsMIG/MAG DC TIG MMAS240V 50/60 Hz+15% / -20%Single phase input16 A Fuse rating (slow blow)4.5 KVA 35%3.4 KVA 60%3.0 KVA 100%4.5 KVA 35%3.4 KVA 60%3.0 KVA 100%4.0 KVA 60% Input power3.7 KVA 100%15A ÷ 160A 5A ÷ 160A 10A ÷ 130A min.-max. current that can be obtained in welding160A 35%130A 60%120A 100%160A 35%130A 60%120A 100%130A 60%120A 100%Duty Cycle, (10 min.40°C)according to IEC 60974.1ElectronicStepless regulation0.6/0.8/1.0 Fe1.0 Al0.8 Inox0.8 Cu-Si 3%0.9 CoredØ 200 mm/5 Kg- - Wire sizes that can be used- - Max. wire spool size- -IP 23 SØ 1.5Ø 3.25Electrodes that can be usedProtection class13 Kg Weight207x437x411HDimensions mmThe power source can be powered by motor generators of adequate power (Min. 6 KVA).298ART.298.11DESCRIPTIONInverter multiprocess single-phase power source for MIG/MAG, DC TIG (with “Cebora lift ignition”) and MMA welding, with2-roller wire feeder and stored synergic curves for MIG/MAG welding, electronic control of choke value, spot welding time andpause time. Comes with 3m CEBORA MIG welding torch Art. 1635 and work return lead (3m - 16mm²).Without flowmeter, MMA welding cables and TIG welding torch.Complies with EN 61000-3-12.Power source as above. Comes with work return lead (3m - 16mm²).Version without MIG/MAG torch, without flowmeter, MMA welding cables and TIG welding torch.1635 3 m. MIG torch.1636 “PROFESSIONAL” CEBORA MIG torch - 3 m long (special for cored wire).1637 3 m “CEBORA” TIG welding torch. With control push-button for gas and power.1281Accessories set for electrode welding:electrode holder (4 m. -16mm 2 ),work return lead (4 m - 16 mm2)1432 Trolley for transportation of the power source only, with 180 mm gas bottle.1656 Trolley for transportation of the power source with 230 mm gas bottle.1659 Trolley for carrying up to 2 power sources and 180 mm gas bottle.1451 2 gauge flowmeter.1934 Aluminium welding kit consisting of: liner, wire feed roller and contact tip for ø 1 mm wire.For torches Art. 1635 and 1636.136 Software updating kit.2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL47

sound mig 2230/M star synergicsynergic inverter mig/mag welding single-phase power source.Art. 299 Specifications240V 50/60 Hz+15% / -20%Single phase inputS20 A Fuse rating (slow blow)6.8 KVA 30%4.9 KVA 60%3.5 KVA 100%15A ÷ 220A220A 30%175A 60%145A 100%Input powerMin.-max. current that can be obtained in weldingDuty Cycle, (10 min.40°C)according to IEC 60974.1Electronic0.6/0.8/0.9/1.0/1.2 Fe0.8/0.9/1.0/1.2 Al0.6/0.8/0.9/1.0/1.2 Inox0.8/0.9/1.0 Cu-Si 3%0.8/1.0 Cu-Al8 (AlBz8)0.9 CoredØ 300 mm/15 KgStepless regulationWire sizes that can be usedMax. wire spool sizeIP 23 SProtection class27 Kg Weight320x585x500HDimensions mmThe power source can be powered by motor generators of adequate power (Min. 8 KVA).299ART.DESCRIPTIONSynergic inverter MIG/MAG welding single-phase power source, with 2-roller wire feed unit in aluminium, with manual/synergiccontrol panel with stored curves. Comes with work return lead (3,5 m - 25 mm²) and clamp.Comes without welding torch.Complies with EN 61000-3-12.2003 4 m (12 ft) CEBORA PUSH-PULL, UP-DOWN torch.1242 “CEBORA 280 A” torch 3,5 m (9 ft) long. Euro type connection1656 Trolley for transportation of the power source.159 Additional support for fixing the power source Art. 299 on the transportation trolley Art. 1656.1451 2 gauge flowmeter.1933Aluminium welding kit consisting of:4,3 m. wire liner assy for 1,0-1,2 mm wire and wire guide pipe (for torch Art. 1242).48PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

sound mig 2060/MD star double pulseinverter mig/mag welding single-phase power source. double pulse.Art. 301 Specifications240V 50/60 Hz+15% / -20%Single phase inputS20 A Fuse rating (slow blow)5.7 KVA 60%4.1 KVA 100%Input power15A ÷ 200A200A 60%160A 100%ElectronicMin.-max. current that can be obtained in weldingDuty Cycle, (10 min.40°C)according to IEC 60974.1Stepless regulation0.6/0.8/1.0 Fe0.6/0.8/1.0/1.2 Al0.6/0.8/1.0 Inox0.8/1.0 Cu-Si 3%0.8/1.0 Cu-Al8 (AlBz8)Ø 200 mm/5 KgØ 300 mm/15 KgWire sizes that can be usedMax. wire spool sizeIP 23 SProtection class21.5 Kg Weight260x580x471HDimensions mm301ART.DESCRIPTIONSynergic inverter MIG/MAG double pulse single-phase welding power source, with 2-roller wire feed unit in aluminium, withmanual/synergic control panel with stored curves, electronic control of choke value, spot welding time and pause time. Comeswith work return lead (3 m - 25 mm²) and clamp.Comes without welding torch.Complies with EN 61000-3-12.2003 4 m (12 ft) CEBORA PUSH-PULL, UP-DOWN torch.1242 “CEBORA 280 A” torch 3,5 m (9 ft) long. Euro type connection1451 2 gauge flowmeter.114 Kit for 15 kg. Ø 300 mm wire reels.1656 Cart for transportation of the power source when used with kit art. 114.1933Aluminium welding kit consisting of:4,3 m. wire liner assy for ø 1,0-1,2 mm wire and wire guide pipe (for torch Art. 1242).2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL49

sound mig 2060/MD star double pulseArt. 301 + 2003Art. 2003Art. 301301ART.DESCRIPTIONSynergic inverter MIG/MAG double pulse single-phase welding power source, with 2-roller wire feed unit in aluminium, withmanual/synergic control panel with stored curves, electronic control of choke value, spot welding time and pause time. Comeswith work return lead (3 m - 25 mm²) and clamp.Comes without welding torch.Complies with EN 61000-3-12.2003 4 m (12 ft) CEBORA PUSH-PULL, UP-DOWN torch.ART.DESCRIPTION1812 Contact tip ø 0.8 for Fe/stainless steel/cored wire/CuSi3-AlBz8 (10 pcs).1813 Contact tip ø 1.0 for Fe/stainless steel/cored wire/CuSi3-AlBz8 (10 pcs).1819 Contact tip ø 1.0 for Aluminium (10 pcs).1822 Contact tip ø 0.8 for Aluminium (10 pcs).consumables1823 Contact tip ø 0.6 for Fe/stainless steel/cored wire/CuSi3-AlBz8 (10 pcs).1838 Welding gas nozzle.1496 Gas diffusor.1887 Aluminium/12% silicon AWS 4047 wire reel Ø 0.6 Kg. 11882 Aluminium/12% silicon AWS 4047 wire reel Ø 0,8 Kg. 21883 Aluminium/12% silicon AWS 4047 wire reel Ø 1 Kg. 21884 AL/Mg 5% AWS 5356 wire reel Ø 0,8 Kg. 21885 AL/Mg 5% AWS 5356 wire reel Ø 1 Kg. 21886 Copper/silicon 3% wire reel Ø 0.8 Kg. 2 for braze welding.50PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

sound mig 2060/MD star double pulseArt. 301 + 1242Art. 1242Art. 301301ART.DESCRIPTIONSynergic inverter MIG/MAG double pulse single-phase welding power source, with 2-roller wire feed unit in aluminium, withmanual/synergic control panel with stored curves, electronic control of choke value, spot welding time and pause time. Comeswith work return lead (3 m - 25 mm²) and clamp.Comes without welding torch.Complies with EN 61000-3-12.1242 CEBORA 280 A torch 3,5 m (9 ft.) long. Euro type connectionART.DESCRIPTION1812 Contact tip ø 0.8 for Fe/stainless steel/cored wire/CuSi3-AlBz8 (10 pcs).1813 Contact tip ø 1.0 for Fe/stainless steel/cored wire/CuSi3-AlBz8 (10 pcs).1819 Contact tip ø 1.0 for Aluminium (10 pcs).1820 Contact tip ø 1.2 for Aluminium (10 pcs).1822 Contact tip ø 0.8 for Aluminium (10 pcs).consumables1823 Contact tip ø 0.6 for Fe/stainless steel/cored wire/CuSi3-AlBz8 (10 pcs).1834 Cylindrical welding gas nozzle.1886 Copper/silicon 3% wire reel Ø 0.8 Kg. 2 for braze welding.1933 Aluminium welding kit consisting of: 4,3 m. wire liner assy for 1,0-1,2 mm wire and wire guide pipe (for torch Art. 1242).2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL51

sound mig 2060/MD star double pulseArt. 301 + 1656 + 114301ART.DESCRIPTIONSynergic inverter MIG/MAG double pulse single-phase welding power source, with 2-roller wire feed unit in aluminium, withmanual/synergic control panel with stored curves, electronic control of choke value, spot welding time and pause time. Comeswith work return lead (3 m - 25 mm²) and clamp.Comes without welding torch.Complies with EN 61000-3-12.114 Kit for 15 kg. Ø 300 mm wire reels.1656 Cart for transportation of the power source when used with kit art. 114.52PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

sound mig 2740/T star pulsesynergic inverter mig/mag pulse welding power source.Art. 307 Specifications415V 50/60 Hz+15% / -20%Three phase inputS16 A Fuse rating (slow blow)10.4 KVA 40%9.0 KVA 60%8.1 KVA 100%15A ÷ 275A275A 40%255A 60%240A 100%Input powerMin.-max. current that can be obtained in weldingDuty Cycle, (10 min.40°C)according to IEC 60974.1ElectronicStepless regulation0.8/0.9/1.0/1.2 Fe0.8/0.9/1.0/1.2 Al0.8/0.9/1.0/1.2 Inox Wire sizes that can be used0.8/0.9/1.0 Cu-Si 3%0.8/0.9/1.0 Cu-Al8 (AlBz8)Ø 300 mm/15 KgMax. wire spool sizeIP 23 SProtection class67 Kg Weight510x970x960HDimensions mm307ART.DESCRIPTIONSynergic inverter MIG/MAG Pulse welding power source. Comes with control panel, 4-roller wire feed unit in aluminium, trolleyfor transportation of the power source and earth cable (3,5 m - 35 mm²).Comes without cooling unit and welding torch.Complies with EN 61000-3-12.1241 “CEBORA 380 A” water cooled torch 3,5 m (9 ft) long.12422009“CEBORA 280 A” torch 3,5 m (9 ft) long.Euro type connection.6 m (20 ft) CEBORA PUSH-PULL, Up/Down WATER COOLED torch (350 A - 60%). To be used together with COOLING UNIT andPUSH PULL INTERFACE KIT..126 Cebora Push Pull torch interface kit. To be used together with Push-Pull torch art. 2009 and cooling unit.1681 GRV14 Torch cooling unit.1451 2 gauge flowmeter.1929 Aluminium welding kit consisting of: 3,5 m. wire liner assy for 1,0-1,2 mm wire and wire guide pipe. (for torch art 1241).1930 3,5 m. wire liner assy for 1,2-1,6 mm wire and wire guide pipe. (for torch Art. 1241).1933Aluminium welding kit consisting of:4,3 m. wire liner assy for 1,0-1,2 mm wire and wire guide pipe (for torch Art. 1242).Upgrade to Double Pulse.For art. 2009 PUSH PULL torch liners andswan neck art. 1859 see page 62.54PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

sound mig 3540/T star pulsesynergic inverter multiprocess pulse power source for mig/mag, tig and mma weldingArt. 309 Specifications415V 50/60 Hz±10%Three phase inputS16 A Fuse rating (slow blow)13.1 KVA 40%10.4 KVA 60%8.6 KVA 100%5A ÷ 350A350A 40%280A 60%260A 100%Electronic0.8/0.9/1.0/1.2 Fe0.9/1.0/1.2 Al0.8/0.9/1.0/1.2 Inox0.8/0.9/1.0 Cu-Si 3%Ø 300 mm/15 KgØ 1.5 ÷ Ø 6IP 23 SInput powerMin.-max. current that can be obtained in weldingDuty Cycle, (10 min.40°C)according to IEC 60974.1Stepless regulationWire sizes that can be usedMax. wire spool sizeElectrodes that can be usedProtection class80 Kg Weight590x1090x960HDimensions mm.309ART.DESCRIPTIONSynergic inverter multiprocess power source for MIG/MAG, Pulse, MMA and DC TIG (with Cebora lift ignition) welding. Comeswith control panel, with wire feed unit in aluminium (4-roller), trolley for transportation of the power source and earth cable(3.5 m - 35 mm²).Comes without cooling unit and welding torch.Complies with EN 61000-3-12.1239 “CEBORA 380 A” torch 3,5 m (9 ft) long.1241 “CEBORA 380 A” water cooled torch 3,5 m (9 ft) long.1256 BINZEL “ABITIG 450 W” Water cooled torch (450 Amp) 4 m. length.1258 BINZEL “ABITIG 450 W” Up/Down. Water cooled torch (450 Amp) 4 m. length.1165 Adapter for connecting the TIG Binzel torch Art. 1256-1258 to the power source.20082008.106 m (20 ft) CEBORA PUSH-PULL, Up/Down WATER COOLED torch (350 A - 60%). To be used together with COOLING UNIT andPUSH PULL INTERFACE KIT.10 m (32 ft) CEBORA PUSH-PULL, Up/Down WATER COOLED torch (350 A - 60%). To be used together with COOLING UNITand PUSH PULL INTERFACE KIT.106 Cebora Push Pull torch interface kit. To be used together with Push-Pull torch art. 2008-2008.10 and cooling unit art. 1683.1683 GRV12 Torch cooling unit.1451 2 gauge flowmeter.Upgrade to Double Pulse.2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL55

sound mig 3840/T star pulsesynergic INVERTER multiprocess pulse power source for mig/mag, tig and mma welding.Art. 387 Specifications415V 50/60 Hz+15% / -20%Three phase inputS20 A Fuse rating (slow blow)15.9 KVA 40%13.2 KVA 60%11.7 KVA 100%5A ÷ 380A380A 40%340A 60%310A 100%Input powerMin.-max. current that can be obtained in weldingDuty Cycle, (10 min.40°C)according to IEC 60974.1Electronic0.6/0.8/0.9/1.0/1.2/1.6 Fe0.8/0.9/1.0/1.2/1.6 Al0.6/0.8/0.9/1.0/1.2/1.6 Inox0.8/0.9/1.0/1.2 Cu-Si 3%0.8/1.0/1.2 Cu-Al8 (AlBz8)1.2/1.6 CoredØ 300 mm/15 KgStepless regulationWire sizes that can be usedMax. wire spool sizeØ 1.5 ÷ Ø 6IP 23 SElectrodes that can be usedProtection class101 Kg Weight705x1060x1380HDimensions mm387ART.DESCRIPTIONSynergic inverter multiprocess power source for MIG/MAG, Pulse, MMA and DC TIG (with Cebora lift ignition) welding. Comeswith control panel, wire feed unit with 4 roll (ø 40 mm) aluminium wire feed block, cooling unit, trolley for transportation ofthe power source and earth cable (3.5 m - 50 mm²).Without torch and extension.Complies with EN 61000-3-12.1241 “CEBORA 380 A” water cooled torch 3,5 m long.1245 “CEBORA 500 A Up/Down” water cooled torch 3,5 m long.1259 ABITIG 200 torch - 4 m long.”Euro” type connection.20082008.106 m (20 ft) CEBORA PUSH-PULL, Up/Down WATER COOLED torch (350 A - 60%). To be used together with COOLING UNIT andPUSH PULL INTERFACE KIT.10 m (32 ft) CEBORA PUSH-PULL, Up/Down WATER COOLED torch (350 A - 60%). To be used together with COOLING UNITand PUSH PULL INTERFACE KIT.106 Cebora Push Pull torch interface kit. To be used together with Push-Pull torch art. 2008-2008.10 and cooling unit.1197 5 m. extension lead between power source and wire feeder.1197.20 10 m. extension lead between power source and wire feeder.471H.F. “unit 3500” to simultaneously attach MIG and TIG torch and with HF ignition function for TIG. Comes with 1,5 m extensionlead between power source and wire feed unit.1451 2 gauge flowmeter.Upgrade to Double Pulse.56PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

sound mig 5040/T star pulsesynergic INVERTER multiprocess pulse power source for mig/mag, tig and mma welding.Art. 389 Specifications415V 50/60 Hz+15% / -20%Three phase inputS32 A Fuse rating (slow blow)25.0 KVA 40%21.0 KVA 60%19.5 KVA 100%5A ÷ 500A500A 40%450A 60%430A 100%Input powerMin.-max. current that can be obtained in weldingDuty Cycle, (10 min.40°C)according to IEC 60974.1Electronic0.6/0.8/0.9/1.0/1.2/1.6 Fe0.8/0.9/1.0/1.2/1.6 Al0.6/0.8/0.9/1.0/1.2/1.6 Inox0.8/0.9/1.0/1.2 Cu-Si 3%0.8/1.0/1.2 Cu-Al8 (AlBz8)1.2/1.6 CoredØ 300 mm/15 KgStepless regulationWire sizes that can be usedMax. wire spool sizeØ 1.5 ÷ Ø 6IP 23 SElectrodes that can be usedProtection class115 Kg Weight705x1060x1380HDimensions mm389ART.DESCRIPTIONSynergic inverter multiprocess power source for MIG/MAG, Pulse, MMA and DC TIG (with Cebora lift ignition) welding. Comeswith control panel, wire feed unit with 4 roll (ø 40 mm) aluminium wire feed block, cooling unit, trolley for transportation ofthe power source and earth cable (3.5 m - 90 mm²).Without torch and extension.Complies with EN 61000-3-12.1243 “CEBORA 500 A” water cooled torch 3,5 m long.1245 “CEBORA 500 A Up/Down” water cooled torch 3,5 m long.1259 ABITIG 200 torch - 4 m long.”Euro” type connection.20082008.106 m (20 ft) CEBORA PUSH-PULL, Up/Down WATER COOLED torch (350 A - 60%). To be used together with COOLING UNIT andPUSH PULL INTERFACE KIT.10 m (32 ft) CEBORA PUSH-PULL, Up/Down WATER COOLED torch (350 A - 60%). To be used together with COOLING UNITand PUSH PULL INTERFACE KIT.106 Cebora Push Pull torch interface kit. To be used together with Push-Pull torch art. 2008-2008.10 and cooling unit.1197 5 m. extension lead between power source and wire feeder.1197.20 10 m. extension lead between power source and wire feeder.471H.F. “unit 3500” to simultaneously attach MIG and TIG torch and with HF ignition function for TIG. Comes with 1,5 m extensionlead between power source and wire feed unit.1451 2 gauge flowmeter.Upgrade to Double Pulse.2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL57

Mig torchesArt. 1239 Art.1241 Art. 1242 Art. 1243Art. 1245 Art. 1275 Art. 1276 Art. 1559.01Art. 1635 Art. 1636 Art. 2003ART. DESCRIPTION per/for Art.1239 “CEBORA 380A” torch - 3.5 mt. long. “Euro” type connection. (380A -60%) 309-641-643-6471241 “CEBORA 380A” Water cooled torch - 3.5 mt. long.”Euro” type connection.1242 “CEBORA 280A” torch - 3.5 mt. long. “Euro” type connection. (280A -60%)302-307-309-387387.05-643-647299-301-302-307622-624-625-6276331243 “CEBORA 500A” Water cooled torch - 3.5 mt. long.”Euro” type connection. 389-389.05-6471245 “CEBORA 500A” Water cooled Up/Down torch - 3.5 mt. long. “Euro” type connection.387-387.05-389389.051275 3 m. long CEBORA MIG torch 283-283.111276 “PROFESSIONAL” CEBORA MIG torch 3 mt. long. (Special for flux cored wire) 283-283.111559.01 CEBORA torch - 3 mt. long.Direct connection. 4951635 CEBORA MIG torch - 3 mt. long. 298-298.111636 “PROFESSIONAL” CEBORA MIG torch - 3 m long (special for cored wire). 298-298.112003 4 m CEBORA PUSH-PULL. Up/Down torch.299-301-302-622627-64158PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

ACCESSORIES And consumables for mig/mag torchesMig torchesART.DESCRIPTION12391241124212431245127512761559.011635163620031457 Contact tip Ø 0.6. X X X1459 Contact tip Ø 0.8. X X X1460 Contact tip Ø 1.0. X X1462 Contact tipØ 0.9 for cored wire. X X X1823 Contact tip ø 0.6 for Fe/stainless steel/cored wire CuSi3-AlBz8 (10 pcs). X X X X X X X X1812 Contact tip Ø 0.8 for Fe/stainless steel/cored wire CuSi3-AlBz8 (10 pcs). X X X X X X X X1824 Contact tip ø 0.9 for Fe/stainless steel/cored wire/CuSi3-AlBz8 (10 pcs). X X X X X X X X1813 Contact tip Ø 1.0 for Fe/stainless steel/cored wire CuSi3-AlBz8 (10 pcs). X X X X X X X X1814 Contact tip Ø 1.2 for Fe/stainless steel/cored wire CuSi3-AlBz8 (10 pcs). X X X X X X1815 Contact tip Ø 1.4 for Fe/stainless steel/cored wire CuSi3-AlBz8 (10 pcs). X X X X X X1816 Contact tip Ø 1.6 for Fe/stainless steel/cored wire CuSi3-AlBz8 (10 pcs). X X X X X1817 Contact tip Ø 2.0 for Fe/stainless steel/cored wire CuSi3-AlBz8 (10 pcs). X X X X X1822 Contact tip ø 0.8 for Aluminium (10 pcs). X X X X X X1825 Contact tip ø 0.9. For Aluminium (10 pcs). X X X X X X1819 Contact tip Ø 1.0 for Aluminium. (10 pcs). X X X X X X X X1820 Contact tip Ø 1.2 for Aluminium. (10 pcs). X X X X X1821 Contact tip Ø 1.6 for Aluminium. (10 pcs). X X1461 Cone shaped welding gas nozzle. X1829 Cone shaped welding gas nozzle. X X X X1833 Cone shaped welding gas nozzle. X X1834 Cylindrical welding gas nozzle. X X X X1838 Welding gas nozzle. X1839 Welding gas nozzle. X X X1463 Spot welding gas nozzle. X X X1496 Gas diffuser. X1955 Gas diffuser. X X X1966 Ceramic gas diffuser . X X X X1469 Swan neck. X1864 Swan neck. X X1865 Swan neck. X1866 Swan neck. X1867 Swan neck. X1868 Swan neck. X X1869 Swan neck. X X1466 Swan neck spring. X X1956 Gas nozzle insulated support. X X X X2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL59

ACCESSORIES And consumables for mig/mag torchesMig torchesART.DESCRIPTION12391241124212431245127512761559.011635163620031957 Contact tip support. X X X X1965 Contact tip support. X X X1926 Wire guide liner kit Ø 1.0-1.2 for Fe/stainless steel/cored wire. X X X1927 Wire guide liner kit Ø 1.2-1.6 for Fe/stainless steel/cored wire. X X X1931 Wire guide liner kit Ø 0.6-0.9 - Blue 3.5m. for Fe/stainless steel/cored wire. X X1936 Wire guide liner kit Ø 0.6-1.0 - Blue 3.5m. for Fe/stainless steel/cored wire. X X X X1932 Wire guide liner kit Ø 1.0-1.2 - red 3.5m for Fe/stainless steel/cored wire. X X2335 Insulating washer for contact tip support. X X XAluminium welding kit consisting of: 3.5 m. wire liner assy for 1.0-1.2 mm wire1929X X X Xand wire guide pipe.Aluminium welding kit consisting of: 4.3 m. wire liner assy for 1.0-1.2 mm wire1933Xand wire guide pipe.Aluminium welding kit consisting of: liner, wire feed roller and contact tip for1934ø 1 mm wire1930 3.5 m. wire liner assy for 1.2-1.6 mm Al wire. X X X XX X X XX1464.01 Spiral sheet for Fe/Stainless steel. X1925 Spiral sheet kit for Fe/Stainless steel. X60PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

MIG-MAG WELDING GUN FOR DIN 8559 SPOOLS. 200A 60%spool gun1562ART.DESCRIPTIONMIG-MAG welding gun with small size spool (DIN 8559) for aluminium, steel, iron. Complete with: 0.5 Kg spool of Ø 1 mmaluminium wire, current nozzles, Ø 0.6-0.8-1-1.2 mm, gas nozzle, 2 mm allen wrench.1196 6 m extension.1196.20 12 m extension.ART.DESCRIPTION1591 Al/Mg 5% wire reel Ø 0.8 Kg. 0.5consumables1592 Al/Mg 5% wire reel Ø 1 Kg. 0.51823 Contact tip ø 0.6 for Fe/stainless steel/cored wire/CuSi3-AlBz8. (10 pcs.).1812 Contact tip Ø 0.8 for Fe/stainless steel/cored wire/CuSi3-AlBz8. (10 pcs).1824 Contact tip ø 0.9 for Fe/stainless steel/cored wire/CuSi3-AlBz8 (10 pcs).1813 Contact tip Ø 1.0 for Fe/stainless steel/cored wire/CuSi3-AlBz8. (10 pcs).1814 Contact tip Ø 1.2 for Fe/stainless steel/cored wire/CuSi3-AlBz8. (10 pcs).1822 Contact tip ø 0.8 for Aluminium (10 pcs.).1825 Contact tip ø 0.9. For Aluminium (10 pcs).1819 Contact tip ø 1.0 for Aluminium (10 pcs.).1820 Contact tip ø 1.2 for Aluminium (10 pcs.).1838 Welding gas nozzle.2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL61

push pull - Art. 2008 - 2008.10 - 2009 - 20106 m. (20 ft) / 10 M (32 ft) cebora push pull, up/down water cooled torch.20082008.1020092010126106ART. DESCRIPTION per/for Art.6 m (20 ft) CEBORA PUSH-PULL, Up/Down WATER COOLED torch. (350 Amp - 60%).To be used together with COOLING UNIT and PUSH PULL INTERFACE KIT.10 m (32 ft) CEBORA PUSH-PULL, Up/Down WATER COOLED torch. (350 Amp - 60%).To be used together with COOLING UNIT and PUSH PULL INTERFACE KIT.6 m (20 ft) CEBORA PUSH-PULL, Up/Down WATER COOLED torch. (350 Amp - 60%).To be used together with COOLING UNIT and PUSH PULL INTERFACE KIT.6 m (20 ft) CEBORA PUSH-PULL, Up/Down WATER COOLED torch. (350 Amp - 60%).To be used together with COOLING UNIT.Cebora Push Pull torch interface kit.To be used together with Push-Pull torch Art. 2009 and cooling unit.Cebora Push Pull torch interface kit.To be used together with Push-Pull torch Art. 2008-2008.10 and cooling unit.309-387-387.05389-389.05309-387-387.05389-389.05307302-643-64720092008-2008.1062PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

push pull - Art. 2008 - 2008.10 - 2009 - 2010ACCESSORIES And consumables for cebora push pull torch.ART. DESCRIPTION per/for Art.1859 Swan neck. Duty cycle 350A at 60%.2008-2008.102009-20101937 Small teflon wire guide liner for swan neck. 18591938 Small brass spiral wire guide liner for swan neck. 18591939Kit for aluminium wires consisting of:-6.2 m PA-CARBON wire guide liner (Art. 1945). -Small teflon wire guide liner for swan neck (Art. 1937).-6 wire guide pipes.2008-2008.102009-20101943Kit for Fe/stainless steel/cored wires consisting of: -6.2 m spiral wire guide liner (Art. 1946).-Small brass spiral wire guide liner for swan neck (Art. 1938).1945 6.2 m PA-CARBON wire guide liner.1946 6.2 m spiral wire guide liner1971 Contact tip Ø 0.8 for Fe/stainless steel/cored wire/CuSi3-AlBz8 (10 pcs.). 18591972 Contact tip Ø 0.9 for Fe/stainless steel/cored wire/CuSi3-AlBz8 (10 pcs.). 18591973 Contact tip Ø 1.0 for Fe/stainless steel/cored wire/CuSi3-AlBz8 (10 pcs.). 18591974 Contact tip Ø 1.2 for Fe/stainless steel/cored wire/CuSi3-AlBz8 (10 pcs.). 18591975 Contact tip Ø 0.8. for Aluminium (10 pcs.). 18591976 Contact tip Ø 0.9. for Aluminium (10 pcs.). 18591977 Contact tip Ø 1.0. for Aluminium (10 pcs.). 18591978 Contact tip Ø 1.2. for Aluminium (10 pcs.). 18591959 Gas diffuser Ø 0.8. 18591828 Cone shaped welding gas nozzle. 18592008-2008.102009-20102008-2008.102009-20102008-2008.102009-20102011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL63

spot 2500MULTI-PURPOSE SPOTTER FOR BODY SHOPSArt. 2148 Specifications415V 50 Hz± 10%Three phase inputS10 A Fuse rating (slow blow)6.0 Kw Max. installed power3000 A max. Current rangeIP 23 SProtection class30 Kg Weight207x437x411HDimensions mm2148ART.DESCRIPTIONSyncronous electronic regulation multipurpose power source. Comes with work return lead (mt.2 - 50 mm2), cable with spotgun (mt. 2.5 - 50 mm2), multipurpose slide hammer to be fitted on the gun, box with set of accessories and consumables.1432 Trolley for transportation of the power source only.ART.DESCRIPTION2290 Sliding hammer with handgrip.consumables and accessories2293 Hammer head for washer traction.2295 Hammer head for pin traction.2296 Spot weld electrode for Ø 3 and Ø 5 rivets.2297 Spot weld electrode for washers.2298 Spot weld electrode for M4 screws and Ø 2 - Ø 2.5 pins.64PROFESSIONAL2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

power spot 5600SPOTTER FOR BODY SHOPSArt. 2154 Specifications240V 50/60 Hz± 10%Single phase inputS10 A Fuse rating (slow blow)E 50 ÷ 1500 J Energy adjustment rangeIP 23SProtection class15 Kg Weight176x370x401HDimensions mm.2154ART.DESCRIPTIONSingle-phase capacitor discharge power source for welding rivets on all kind of sheet metal (iron, stainless steel, aluminium).Comes with gun, earth cable and accessories bag (wrench, rivet mandrels, synthetic steel wool, 1 conf.Art. 2318, 2333 and 2334).Complies with EN 61000-3-12.1432 Trolley for transportation of the power source only.consumables and accessoriesART. DESCRIPTION2318 M4x15 threaded rivets. Aluminium. Package of 100 pieces.2333 Special washers. Package of 5 pieces.2334 3 pin spacer.2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.comPROFESSIONAL65

NOte662011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com

NOte2011 - APRILPRICES AND SPECS MAY CHANGE WITHOUT PRIOR NOTICEPh: 1800 CEBORA; 1800 232 672, www.cebora.com67

2 Hollylea Road, Leumeah, NSW, Australia 2560Phone: 1800 CEBORA; 1800 232 672www.cebora.comCEBORA AUSTRALIA RESERVES THE RIGHT OF MODIFYING THE TECHNICAL SPECIFICATIONS OF THE PRODUCTS INCLUDED IN THIS CATALOGUE WITHOUT NOTICE.