Food Safety Terminal Operators Guide - TransAct

More documents

Recommendations

Info

Safety PrecautionsNever pull on the power cord to unplug the cord from the power supply.Always grip the plug to remove it from the power supply.If the terminal will not be used for a long period, disconnect the power cordfrom the power source.Always keep the area around the power plug free of obstacles so that youcan unplug it easily. This allows you to unplug the power cord quickly in anemergency.Never use any power source other than the one rated for the terminal. Thisterminal is designed to be used in the region where you purchased. Also,make sure that the power source can supply sufficient power for theterminal.Supply Voltage:AC 100-240 V, 50/60 HzHandling the Terminal and AccessoriesTo avoid the risk of fire, electrical shock, personal injury, or damage to theterminal:Never clean the terminal with water or any flammable liquid (alcohol,benzene, thinner, etc.) either applied directly or with a cloth. If youaccidentally spill liquid on the terminal, switch the terminal off immediately,disconnect the power plug from the power source, and call for service.If the terminal emits smoke, unusual odors, or makes noises, leaving itcould cause a fire or serious electrical shock or damage to the terminal.Switch the terminal off immediately, disconnect the power plug from thepower source, make sure that the terminal has stopped smoking, and callfor service. Do not attempt to repair the terminal by yourself.Use only a slightly damp cloth, thoroughly wrung out, to clean the terminalsurfaces. Never use alcohol, thinner or any other flammable liquids, or riskhaving them come into contact with electrical components inside theterminal.There are high voltage points inside the terminal. Never attempt todisassemble or repair the terminal.Never insert or drop any metal objects into the terminal when it is open.This could cause a fire or serious electrical shock, or damage the terminal.If something falls into the terminal accidentally, switch the terminal offimmediately, disconnect the power plug from the power source and call forservice.If the terminal is dropped and damaged, switch the terminal offimmediately, disconnect the power plug from the power source, and callfor service.Never use flammable sprays around the terminal.Never remove the cover from the terminal.Before cleaning the terminal, switch it off and disconnect the power plugfrom the power source.Page 12100-12042 - Rev C
Safety PrecautionsNote: Do not rapidly switch the terminal off and on. This could damage theterminal. After switching the terminal off, wait at least 5 seconds beforeswitching it on again.100-12042 - Rev C Page 13
Page 1: Food Safety TerminalOperators Guide
Page 4 and 5: This page intentionally left blankP
Page 6: DisclaimerNOTICE TO ALL PERSONS REC
Page 12 and 13: About Your Ithaca ® 9700 PrinterWh
Page 14 and 15: About Your Ithaca ® 9700 PrinterRe
Page 16 and 17: About Your Ithaca ® 9700 PrinterTh
Page 22 and 23: Safety PrecautionsThis page intenti
Page 26 and 27: Installation and SetupA startup scr
Page 28 and 29: Installation and SetupLoading Label
Page 30 and 31: Installation and Setup5. Drop the l
Page 32 and 33: Installation and Setup7. Grasp side
Page 34 and 35: Installation and SetupChanging the
Page 36 and 37: Installation and Setup4. Grasp the
Page 39 and 40: Chapter 4Ithaca ® 9700 Specificati
Page 41 and 42: Ithaca ® 9700 Specifications and R
Page 47 and 48: Chapter 5Operating Your Ithaca ® 9
Page 49 and 50: Operating Your Ithaca ® 9700 Print
Page 71 and 72:
Chapter 6Troubleshooting100-12042 -
Page 73 and 74:
TroubleshootingPower is OffCheck Po
Page 75:
Appendix A: Ordering SuppliesAppend
show all

Food Safety Terminal Operators Guide - TransAct

Create successful ePaper yourself

Delete template?

Save as template?