CO30 Laser Marking System - Telesis Technologies, Inc.

More documents

Recommendations

Info

System Setup Complete installation procedures are provided in the CO30 Installation/Maintenance Manual. The following procedures are listed for reference only to provide a general overview of the installation process. 1. Equipment should remain powered down and in the OFF position until the mounting is complete. 2. Place the computer, monitor keyboard and laser controller in the desired location. Locate the controller as close as practical to the laser marking head. The standard umbilical length is 1.8 meters (6 feet). 3. Place the laser marking head onto the mounting position taking care not to bend or kink the umbilical cable. The umbilical cable will take an approximately 200 mm (8 in.) diameter bend without damage. 4. Mount the laser marking head per the following guidelines: • A minimum distance of 200 mm (8 in.) should be allowed at the rear of the laser marking head to allow for proper installation of the umbilical. • Mount the laser marking head using three M8-1.25 bolts and lock washers. Torque to 191 in-lbs (21.59 N-m). • Mounting bolts must not extend into the laser marking head as to interfere with the internal components or the optical beam path. • Refer to the Dimensions and Mounting Details drawing for mounting bolt locations and note the following: – Pay particular attention to the location of the center of the marking window as dimensioned on the appropriate mounting drawing (see next page). – The leading edge of the mounting plate should be no greater than 31.7mm (1.25 in.) from the first set of holes to allow clearance for the beam output lens. 5. Ensure laser controller power switch (on front panel) is OFF. 6. Connect the remaining cables. 7. Refer to the CO30 Operation Supplement for proper startup procedure of the complete system. 8. Refer to the laser marking system Operation Manual for complete information on using the system software. CO30 Laser Marking System System Specifications Compliance .................................CDRH Laser Type...................................RF-excited, continuous wave, sealed-tube, carbon dioxide laser Wavelength .................................10.6 micrometers (µm) CW Average Power ....................30 watts Long Term Output Power Drift ...< ±5% Total Power Consumption...........approx. 6.0 amps at 115 VAC Input Power .................................115 VAC, single-phase, 15A, 50/60Hz 230 VAC, single-phase, 7.5A, 50/60Hz Supply Voltage Fluctuation.........< ±10% with clean ground line Operational Temperature.............15° to 30°C (59° to 86°F) Recommended Temperature........16° to 24°C (61° to 75°F) Ambient Relative Humidity ........10% to 90% non-condensing Laser Marking Head The laser marking head incorporates the latest technology in sealed-tube, RF-excited, carbon dioxide lasers, providing excellent output power, stability, and reliability in a rugged compact modular package. Laser Marking Head Specifications Dimensions (L x W x H) .............973.5 x 146.88 x 204.5 mm (38.33 x 5.78 x 8.05 in.) Surrounding Envelope.................1181 x 355 x 405 mm (46.5 x 14.0 x 16.0 in.) Mounting Weight .......................approx. 21.82 Kg (48 lbs.) Mounting Holes...........................three factory-tapped M8-1.25 Positioning...................................visible red aiming diode (optional for mark-on-the-fly systems) Field Resolution ..........................16 bit (65535 data points) Galvanometer Repeatability ........< 22 micro radian Marking Field Size .....................lens-dependent, see chart Laser Umbilical Cable Length.....1.8 m (6 ft.), detachable Cooling........................................air cooled, fan/filter Doc No. 47713 Rev. E 2 of 7
CO30 Laser Marking Head with 7mm Galvo – Dimensions and Mounting Details CO30 Laser Marking Head with 10mm Galvo – Dimensions and Mounting Details CO30 Laser Marking System Doc No. 47713 Rev. E 3 of 7
Page 1: System Overview The Telesis ® CO30
Page 5 and 6: System PC The laser system requires
Page 7: Communications Protocol (continued)

CO30 Laser Marking System - Telesis Technologies, Inc.

Create successful ePaper yourself

Delete template?

Save as template?