parts, articles on originality introduction to index - Steve Plucker

A-6335: Crankshaft rear bearing seal“Tip on Gaskets”: MAN/35/3/7 (1988)**332A-6346: Crankshaft front and center bearing shim“TIP…Use Correct Shims to Prevent Leaking Oil”: TR/5/4/9 (1960)OTHER ARTICLES ON THE CAMSHAFT AND CRANKSHAFT“TIP…Timing Gear Problem”: TR/23/2/8 (1978)“TIP…Great Way To Find Top Dead Center”: TR/50/2/7 (2005)“Engine Turner Tool”: TR/50/6/2006 (2006)“Lubricate Your Bearings Henry’s Way”: TR/54/5/21-23 (2010)“Engine Built with Reproduction Parts (Cam Bushings)”: MAT/5/1/7-8, 32 (2009)“Flat Tappets, Model A Engines and Motor Oil”: MAT/6/1/9-13 (2010)“Trouble From the Start”: MAT/7/1/4-5 (2011)FLYWHEEL AND VALVESA-6375-B: Flywheel Assembly“TIP…Installing the Flywheel”: MAN/21/6/30 (1974)**2“TIP…Jumping Out of Gear…Things To Check”: TR/16/3/40 (1973)“Tinkering With Our Toys”: TR/27/2/11-15 (1982)*3“Alignment of the Flywheel Housing”: TR/28/5/10-15 (1984)*4“The Model A Ford Drive Train…Understanding Basic Operations and TroubleConditions”: TR/35/5/24-31 (1991)“Removing the Flywheel from the Crankshaft the Easy Way”: TR/42/3/6 (1997)“Installing the Flywheel Ring Gear”: TR/55/5/11 (2011)“Flywheel Removal”: MAT/8/2/10 (2012)A-6384: Flywheel ring gear“TIP…Removing and Installing”: TR/16/3/32 (1971)“TIP…For Easy Installation…”: TR/43/5/30 (1999)“Installing the Flywheel Ring Gear”: TR/55/5/11 (2011)A-6395: Flywheel housing“LETTER…Flywheel Housing Hole”: MAN/UNKNOWN/p. 19/**4“On the Road”: MAN/32/1/21 (1985) **6“Emily A-241”: MAN/35/5/10 (1988)“TIP…Jumping Out of Gear…Things To Check”: TR/18/3/40 (1973)“TIP…(Retreving) Stray Parts in Flywheel Housing”: TR/23/2/9 (1978)“TIP…Flywheel Housing Hole”: TR/43/1/3 (1998)“How to Safety Wire the Bolts on the Model A Ford”: TR/51/2/8-10 (2006)*8“Snyders Antique Auto Parts…NEW”: MAT/5/4/10-11 (2009)A-6398: Flywheel housing shield“On the Road”: MAN/32/1/21 (1985) **6A-6500-A: Valve push rod“Tappet Clearances and Cam”: TR/10/3/7-9 (1965)*1“Flat Tappets, Model A Engines and Motor Oil”: MAT/6/1/9-13 (2010)A-6505-A: Intake and exhaust valve“Causes of Valve Warping”: MAN/??/?/?? (19??)**1“Burning Valves”: MAN/17/2/23 (1970)**2“Cleaning Carbon and Grinding Valves”: MAN/24/3/18-19 (1977)**4“Model “A” Valve Timing”: MAN/30/2/18-20 (1983)**5“LETTER…Grinding of Valves and Valve Seats”: MAN/36/2/5 (1989)“Adjusting Valves”: MAN/41/3/14 (1994)“Tappet Clearance Effect on Noise”: MAN/42/4/9 (1995)“LETTER…More on Valve Clearance”: MAN/42/6/4 (1995)“LETTER…More on Valve Adjustment”: MAN/43/1/3 (1996)