TSE-EcoWind T211 Technical Data Sheet.pdf - TSE Industries, Inc.

TECHNICAL DATA SHEETTSE-EcoWIND ® T211Filament Winding Polyurethane Resin forTanks and Pressure VesselsDescriptionTSE-EcoWIND® resins are “Environmentally-Friendly Products”. The 2 part HighPerformance Polyurethane Resin System is totally free of VOC’s such as Styrene andhazardous chemicals like BPA (BPA or Bisphenol-A is a key component of epoxybased systems) as well as Amines, Anhydrides, MEKP.TSE-EcoWIND® T211 Resin Systems are formulated for filament windingapplications serving the filament wound composite tanks and pressure vessels(water softeners, pool filters, storage tanks) market.Features “Environmentally-FriendlyProduct” High PerformanceBenefits“Ultra-low” emissions andfree of Styrene, EliminatesTile V Permitting related toprocessing with styrenatedresinsHigher Mechanical and ThermalProperties Low to no resin shrinkage and Improved product qualityand consistency Manufactured in ISO 9001 Increased batch-to-batchcertified plantsconsistency and qualityTHE INFORMATION HEREIN IS BELIEVED TO BE CORRECT AND RELIABLE. HOWEVER, NO WARRANTY IS EXPRESSED OR IMPLIED REGARDING THEACCURACY OF THESE DATA, AND NONE IS MADE AS TO THE MARKETABILITY OF THE MATERIAL OR ITS FITNESS FOR ANY PURPOSE. THE CONSUMERACCEPTS THE RESPONSIBILITY OF AND THE CONDITIONS FOR LIABILITY OF USE OF THE PRODUCT.TSE INDUSTRIES, INC. CLEARWATER, FL 33760 (727) 573-7676Tech Data TSE-EcoWIND ® T211 Page 1 of 3 EFF: 08/13/2013

Typical Liquid Properties at 23ºC (75ºF)TSE-EcoWIND ® T211 (Part A)Viscosity, cps 1,500Specific Gravity 1.18ColorLight BrownFlash Point (Seta Closed Cup)>200 o CShelf Life12 months*TSE-EcoWIND ® T211 (Part B)Viscosity, cps 1,300Specific Gravity 1.05ColorClear to Light YellowFlash Point (Seta Closed Cup)>190 o CShelf Life12 months* Subject to storage under conditions as recommended below.The gel time when reacted at 1:1 by volume is typically varied from 15-20 minutes,based on the application and temperature.Typical Mechanical PropertiesClearCastingTestMethodGlass Transition Temperature C, (ºF) 84* (183)* ASTM D3418Flexural Strength, MPa (PSI) 91.7 (13,299) ASTM D638Flexural Modulus, MPa (KSI) 2,880(418) ASTM D638Tensile Strength, MPa (PSI) 58.6 (8,500) ASTM D638Tensile Modulus, MPa (KSI) 3,170(460) ASTM D638* Differential Scanning Calorimetry First Scan (T g1)Processing and ApplicationSlight settling may occur upon standing. Agitation to ensure homogeneity is criticalto maintain desired end performance. Processing from a suitable metered mixmachine to achieve 1 Part of Part A to 1 Part of Part B by volume ratio anddispensation at 75 ºF (24 ºC) is essential to maintain desired end performance. Glassfibers are coated with resin using TSE’s patented impregnator to achieve the desiredTHE INFORMATION HEREIN IS BELIEVED TO BE CORRECT AND RELIABLE. HOWEVER, NO WARRANTY IS EXPRESSED OR IMPLIED REGARDING THEACCURACY OF THESE DATA, AND NONE IS MADE AS TO THE MARKETABILITY OF THE MATERIAL OR ITS FITNESS FOR ANY PURPOSE. THE CONSUMERACCEPTS THE RESPONSIBILITY OF AND THE CONDITIONS FOR LIABILITY OF USE OF THE PRODUCT.TSE INDUSTRIES, INC. CLEARWATER, FL 33760 (727) 573-7676Tech Data TSE-EcoWIND ® T211 Page 2 of 3 EFF: 08/13/2013

physical properties of the end product. A post cure at 135 – 145 F for one hour isnecessary to ensure proper cure and strength of the laminate.StorageStore both TSE-EcoWIND ® T211 (Part A) and TSE-EcoWIND ® T211(Part B) in tightlyclosed containers and protected from contamination from moisture and foreignsubstances, which can adversely affect processing. Any opened packages should beblanketed using dry gas (Nitrogen/Argon) and resealed tightly so as to keep moisturefrom entering the sealed container. TSE-EcoWIND ® T211 (Part A) will react withwater to form ureas and CO2 gas, which may cause sealed containers to expand andrupture. For maximum storage life, sealed containers should be stored between 70ºFand 95ºF.Standard PackageComponents are supplied in5-gallon pails55-gallon drums275-gallon totesSafety and Handling(40 [Part B] to 45 [Part A] Lbs. Net),(450 [Part B] to 500 [Part A] Lbs. Net),(2,500 [Part B]-2,800 [Part A] Lbs. Net)Refer to the Material Safety Data Sheet (MSDS) before handling either TSE-EcoWIND ®T211 (Part A) or TSE-EcoWIND ® T211 (Part B). It is the responsibility of the operatorto completely read and understand the MSDS for each component before handlingthem. If for any reason you are not clear on the proper safety and handlingprocedures please contact your TSE representative for additional information.THE INFORMATION HEREIN IS BELIEVED TO BE CORRECT AND RELIABLE. HOWEVER, NO WARRANTY IS EXPRESSED OR IMPLIED REGARDING THEACCURACY OF THESE DATA, AND NONE IS MADE AS TO THE MARKETABILITY OF THE MATERIAL OR ITS FITNESS FOR ANY PURPOSE. THE CONSUMERACCEPTS THE RESPONSIBILITY OF AND THE CONDITIONS FOR LIABILITY OF USE OF THE PRODUCT.TSE INDUSTRIES, INC. CLEARWATER, FL 33760 (727) 573-7676Tech Data TSE-EcoWIND ® T211 Page 3 of 3 EFF: 08/13/2013