Specalog for 160H Motor Grader, AEHQ5450 - Wagner Asia ...

Hydraulic SystemCircuit typeClosed center load sensePump typeaxial pistonPump output @ 2100 RPM 206 L/min 54.4 gal/minMaximum system pressure 24 150 kPa 3,500 psiReservoir tank capacity 38 L 9.9 galStandby Pressure 3100 kPa 450 psiOperating SpecificationsTop Speed - Fwd. 43.6 km/h 27.1 mph- Rev. 34.4 km/h 21.4 mphTurning radius (outside front tires) 7.5 m 24.6 ftSteering range - left/right 50°Articulation angle - left/right 20°Fwd. 1st 3.8 km/h 2.4 mph2nd 5.1 km/h 3.2 mph3rd 7.5 km/h 4.7 mph4th 10.3 km/h 6.4 mph5th 16 km/h 9.9 mph6th 21.8 km/h 13.5 mph7th 30 km/h 18.6 mph8th 43.6 km/h 27.1 mphRev. 1st 3 km/h 1.9 mph2nd 5.6 km/h 3.5 mph3rd 8.1 km/h 5.1 mph4th 12.6 km/h 7.9 mph5th 23.7 km/h 14.7 mph6th 34.4 km/h 21.4 mphService RefillFuel tank 397 L 105 galCooling system 38 L 10 galHydraulic system - total 80 L 20.8 gal- tank 38 L 9.9 galEngine oil 39 L 10.2 galDifferential/Final drives 47 L 12.4 galTandem housing (each) 64 L 16.9 galCircle drive housing 7 L 1.8 galFront wheel spindle bearing 0.5 L 0.13 galhousingFrameCircle - diameter 1553 mm 60.4 inCircle - blade beam thickness 40 mm 1.6 inDrawbar - height 127 mm 5 in- thickness 76 mm 3 inFront-top/bottom plate - width 305 mm 12 in- thickness 25 mm 1 inFront-side plates - width 241 mm 9.5 in- thickness 12 mm 0.5 inFront-linear weights - min 165 kg/m 112 lb/ft- max 213 kg/m 144 lb/ftFront-section modulus - min 2083 cm 3 127 in 3- max 4785 cm 3 291 in 3Front axle - ground clearance 625 mm 24.6 in- front wheel lean 18°- oscillation angle 32°TandemsHeight 572 mm 22.5 inWidth 201 mm 7.9 inSidewall thickness - inner 16 mm 0.63 in- outer 18 mm 0.71 inDrive chain pitch 51 mm 2 inWheel axle spacing 1522 mm 60 inTandem oscillation - forward 15°- reverse 25°MoldboardBlade width 4267 mm 14 ftMoldboard height 686 mm 27 inThickness 25 mm 1 inArc radius 413 mm 16.25 inThroat clearance 90 mm 3.5 inCutting edge - width 203 mm 8 in- thickness 16 mm 0.63 inEnd bit - width 203 mm 8 in- thickness 16 mm 0.63 inBlade pull - max GVW 20 071 kg 44,249 lb- base GVW 14 109 kg 31,104 lbDown pressure - max GVW 13 808 kg 30,441 lb- base GVW 7839 kg 17,281 lb• Blade Pull calculated at 0.9 traction coefficient, which isequal to ideal no-slip conditions, and Gross Vehicle Weight(GVW).160H Motor Grader specifications15