Schneider Electric Professional Installer Training - Xantrex

Schneider Electric Interactive Professional Installer TrainingCourse descriptionDay 1 – Level 1 – Schneider Electric Conext Grid Tie Inverters(8 hours – 8 NABCEP continuing education credits)This course is intended for current or prospective Schneider Electric Conext Grid Tie Inverter installers as wellas others who want to have a more thorough practical understanding of the Conext product line.Pre-requisite: Some prior knowledge of basic electrical circuits and concepts such as Ohms Law.Course content:This training is on the Schneider Electric Conext product line. The format of the training is a small workgroup witha focus on hands-on training with open dialogue. The course covers a brief overview of conventional and renewableenergy sources, an introduction to grid-tie energy transfer, an overview of Schneider Electric grid-tie products,and detailed discussion of the Schneider Electric Conext features, functions and benefits. Participants will alsoget to practice the physical installation of the Schneider Electric Conext product, training in system wiring andcommissioning of typical applications.Upon completion of the course, participants will have a working understanding of how the Schneider Electric Conextproduct is able to transfer power from renewable to conventional energy systems, an understanding of the functions,features and benefits of the Schneider Electric Conext product line and hands-on experience with the installation andcommissioning of the Schneider Electric Conext product.Course descriptionDay 2 – Level 1 – Schneider Electric Xantrex XW System for grid-interactivebattery based systems (8 hours – 8 NABCEP continuing education credits)This course is intended for current or prospective Schneider Electric Xantrex XW System installers or others whowant to have a more thorough practical understanding of the battery based Schneider Electric XW product line.Pre-requisite: Some prior knowledge of basic electrical circuits and concepts such as Ohms Law.Course content:The focus of this training is on the Schneider Electric Xantrex XW System, a battery based grid-interactive productline. The format of the training is a small workgroup and the focus is on hands-on training with open dialogue. Thecourse includes a brief introduction into conventional and renewable energy sources and storage systems, anintroduction to grid-interactive energy transfer, an overview of grid-interactive products, and a detailed discussion ofthe features, functions and benefits of the Schneider Electric battery based grid-interactive product line. In addition,the training will cover the physical installation of the Schneider Electric Xantrex XW System, training in system wiringand commissioning of typical applications.Upon completion of the course, the participants will have a working understanding of how a grid-interactiveand battery based product is able to transfer renewable power to and from conventional energy systems,an understanding of the functions, features and benefits of the Schneider Electric Xantrex XW System andhands-on experience with the installation and commissioning of the Schneider Electric Xantrex XW System.

Schneider Electric Interactive Professional Installer TrainingCourse descriptionDay 3 – Level 2 – In-depth grid-interactive system design and case studies(8 hours – 8 NABCEP continuing education credits)Pre-requisite: This course is intended for current or new system installers who have already gonethrough the Schneider Electric Xantrex XW or Schneider Electric Conext Level 1 course.Course content:The focus of the training is on system components and in-depth case studies of typical grid-interactive applications.This training is conducted in a small workgroup with a focus on hands-on training with open dialogue. The coursecontent covers training on solar panels, generators, batteries and network communication components. In addition,the design and application of solar array installations, battery banks and generator back-up systems are alsocovered. At least half of the course time will be spent on hands-on design, installation and configuration of varioussystem application case studies.Upon completion of the course, the participants will have a good understanding of how to design,install and commission various configurations of grid-interactive systems.Training informationCost:The cost for the three day training is $250.00 USD per attendee.Cost to attend one day of training is $125.00 USD per attendee.Please note: due to the hands on nature of the training, attendance is limited to 12 people per session.To register please fill out the attached registration form.For more additional information, please contact Jarmo Venalainen at SERenBUTraining@schneider-electric.comCustomized off-site training also available. Please contact us for more information and a quotation.

Schneider Electric training registration formPlease use this form to register for the SchneiderElectric Interactive Professional Installer Training courses.Please fill in the required information below.8999 Nelson WayBurnaby, BC, Canada V5A 4B5Phone: 604 422 8595Fax: 604 420 1591Courses:Please pick the dates for your training sessionby circling the dates on the rightHands-on Conext & XW Training Session July 18-20Hands-on Conext & XW Training Session September 12-14Hands-on Conext & XW Training Session October 19-21Hands-on Conext & XW Training Session November 7-9Hands-on Conext & XW Training Session December 7-9Hands-on Conext & XW Training Session (enter other dates here) >Attendee information:Company name:Company address:Company phone:Attendee name:Attendee name:Attendee name:Attendee name:Attendee name:Company fax:email address:email address:email address:email address:email address:FEES: $250 for a three day session, or $125 for a single day (per attendee)Course fees include breakfast and lunch. Hotel, dinner and transportation costs not included.Payment may be made by credit card or check. Please fill in the registration information and fax or e-mail the completed form toJarmo Venalainen – e-mail: SERenBUTraining@schneider-electric.com | fax: 604 420 1591You will be contacted by e-mail or phone to complete the registration process.Please do not make travel arrangements prior to receiving registration confirmation.Cancellation policy: Cancellation requests must be made no later than 5 days prior to the training date.No refunds will be made thereafter. In the event a course is cancelled by Schneider Electric, the registrant understands thatSchneider Electric will not be held responsible for any costs incurred by the registrant except for the refund of the course cost.©2011 Schneider Electric. All rights reserved. Conext, Xantrex, Schneider Electric, and Schneider Electric logo are trademarksor registered trademarks of the Schneider Electric group of companies.