installation instructions vega heatsink fluorescent slider dimmers

VEGA HEATSINK FLUORESCENT SLIDER DIMMERMultiple Ganging of DimmersVega Heatsink Slider Dimmers are mounted with No Fins Broken.Any combination of dimmer models may be ganged together. The dimmersmust be spaced to the dimensions shown in Figure 1. Allow 6” of clearanceabove and below the dimmers.Figure 12 3 /4" 3 5 /8" 4 1 /2"How to determine Wallbox SizeSmall DimmerV500ESIV2000FAMUV2000HDFULarge DimmerV1500EBU4 1 /4"2 5 /8" 4 5 /16"Size: SmallSize: LargeMulti-Gang WallboxWhen mounting dimmers, use Table A to determine what size multi-gang wallboxis required.NOTE:A. When installing an even number of small dimmers only use wallbox size listedin Table A and space one additional box 3/4” away from the others.B. When combining small and large dimmers be certain to position a smalldevice at one end and a large device at the other end of the multi-gang box.C. Mount dimmers with heatsink fins aligned vertically.Number of SmallDevices0123456* See Note ATable A0011+1*44+1*77+1*Number of Large Devices11356891124679101213WALLBOX SIZE368101113141649111214151718Ballast DimmersAll Ballast Dimmers are factory-calibrated at 60Hz and do not require low-end lightadjustment. For proper dimming performance, lamps must be operated at full intensityfor 100 hours prior to dimming.V2000FAMU (No derating required)V2000HDFU (No derating required)V1500EBU (see back page)V500ESI (see back page)Philips ControlsFor technical/sales assistance, call: 1-800-526-2731www.lolcontrols.com P/N 85-6259

INSTALLATIONVEGA HEATSINK FLOURESCENT SLIDER DIMMERTrouble Shooting GuideV1500EBU, V1500FAMUFor Advance Mark X ® , Mark VII ® , MagneTek Ballastar ® , & Osram SylvaniaQuicktronic ® Dimmable BallastSymptomLamps do not start, flickeror go out at low-levelOne lamp end repeatedlyblackens prematurelyCannot resolve problemPossible Solution• Linear lamps are particularly sensitive to the correctgrounding of the ballast to the fixture. Verify properground wire installation.• Control device minimum set point adjusted to low.Try raising slightly.• Lamps not seated properly in lamp sockets.Reseat lamps.• To insure control is operating properly, connect anincandescent lamp load across the Red dimming wireand white neutral wire at the wallbox. Control shoulddim the lamp properly.• Possible loose, shorted or broken wires betweenlamp and ballast. Verify wiring is correct and notdamaged.• Call Advance at (800) 372-3331 and MagneTek at(800) 225-5278, or Osram Sylvania at(800) 544-4828 and ask for applications support.Operation• Turn the light on:-Slide the knob up or down to the desired lighting level.• Turn the light off:-Slide the knob downward until it clicks into the positive off position.THREE YEAR LIMITED WARRANTYThe Philips Controls product, when properly installed and under normal conditions of use (without overload, abuse or alteration), is warranted to you, the original user, for a period of three years form thedate of original retail purchase, to be free from defects in materials and workmanship. If during the warranty period you believe the purchased product or any part thereof has such a defect, you must returnthe product (or part) at your cost during such period, with proof of purchase (or if installed by a third-party a written explanation of installation transaction with proof of date), to Philips Controls, 2828 TradeCenter Dr. Ste. 130B, Carrollton, TX 75007, for repair or replacement (or to an authorized Philips Controls supplier which agrees in advance to handle the return and replacement by factory authorization). Ifthe product or part is found by Philips Controls to have been defective in material or workmanship it will be repaired or replaced (as deemed necessary by Philips Controls), and the replacement will bereturned to you free of charge. The original user is solely responsible for any costs associated with removal and re-installation of the product and shipping to Philips Controls or its authorized supplier.PHILIPS CONTROLS LIMITS THE DURATION OF THE IMPLIED WARRANTY OF MERCHANTABILITY WITH RESPECT TO THE PRODUCT TO THE LIMITED WARRANTY PERIOD SET FORTH ABOVE, AND OTHERWISEDISCLAIMS ALL IMPLIED WARRANTIES WITH RESPECT TO THE PRODUCT AND ITS PARTS. Some states disallow certain limitations on implied warranties so you should consult your state law if you have aquestions regarding this limitation and disclaimer. Philips Controls disclaims any and all liability for incidental, consequential, special or indirect damage arising out of any claimed breach of warranty orotherwise. However, some states do not allow exclusion or limitation of such damages, so this disclaimer may not apply to you.The remedy provided in the Limited Warranty for defective products is the user’s sole and exclusive remedy, subject to your state law. Further, this Warranty gives the user specific legal rights, and the user mayalso have other rights which may vary from state to state.If you believe warranty claim is warranted, you may contact your nearest authorized Philips Controls supplier. If one does not exist in your area, please contact Philips Controls Customer Service at the aboveaddress (or at 1-800-526-2731), or please visit us at www.lolcontrols.com.Exchange of products covered by warranty should be handled through your original supply source.We reserve the right to change details of design, materials and finish in any way that will not alter the installed appearance or reduce function performance.Philips Controls2828 Trade Center Drive, Suite 130B • Carrollton, Texas 75007For technical/sales assistance, call: 1-800-526-2731Made in U.S.A. ©Philips Controls 2000www.lolcontrols.com P/N 85-6259