MDP Manual - Dart Controls

More documents

Recommendations

Info

CONTROLSDescription:Application ExamplesPump Controller with Audible and Visual AlarmA waste pump control which displays the pump rate in liters per minute with an audible andvisual alarm output which will warn the operator if the waste flow has stopped. The alarmshould not be able to be silenced and should automatically reset when flow rates have returnedto normal. The display should indicate in the format "xxx.x" (LPM).Application Diagram:Dart MD10P, MD3P, or MD3EMotor ControlPageItemValuTach153.0MICRO-DRIVEENTERAudibleAnnunciatorFlow Transducer(73 Pulses per Liter)FluidOutletFluidInletDC MotorPumpPump Specs:19 Shaft Rotations = 2 LitersWiring Diagram:MD10PMD3PorMD3EP1-1P1-2P1-3P1-4P1-5P1-6P1-7P1-8NLA-A+COM+5VS1S2*FUSENOT USEDGND+V}AC Line Input 85-265VAC, 50-60 HzSIGNAL OUTMOTORFLOW TRANSDUCER(Frequency Output)P1-9P1-10P1-11P1-12NOCNCIN1NOT USEDNOT USED240VACAudibleAnnunciator* Size fuse according to unit and application. Seeelectrical specifications for maximums.24
Parameter Configuration:Parameter Value Notes10 1 Master, Rate Mode Setting (LPM is a rate-based unit)13 3 Decimal point position set to XXX.X on display30 10 Display should indicate 1.0 LPM (10) when pickup at Reference RPM, parameter 3131 73 This is the RPM at which the Display Reference, parameter 30, should be displayed32 1 Pulses per revolution of shaft encoder or pickup is 1 PPR50 7 Alarm active when pickup stalled53 1 Flash display when alarm is active57 10 Lower limit setting for pickup stall timeout. Set for 10 seconds.Description:Conveyor Oven Controller with Two Preset Process TimesAn oven monitor displaying the “tunnel” time in minutes and seconds. The tunnel time isdefined as the time it takes for the heated object on the conveyor to travel from point A to pointB in the application diagram below. An external time-select switch should allow the user tochoose between the displayed process time or a second fixed process time. The time shouldbe displayed in MM:SS (minutes:seconds) format. The process time should only be allowedto be adjusted between 6:30 and 12:15.Application Diagram:Oven Speed Select SwitchSPEED 1 SPEED 2ABConnect toCouplingHeat SourceTunnel OvenNon-ReducedShaftDart PU-2Eor equivalentCoupling toChain DriveCONTROLSPageItemValuTach6:30MICRO-DRIVEENTERDart MD10P, MD3P, or MD3EMotor ControlGear MotorDrive Train Specs:1380 RPM at non-reducedmotor shaft equates to6 minutes and 40 secondsof tunnel timeWiring Diagram:25
Page 1 and 2: MDP CONTROL SERIESCONTROLSInstructi
Page 3 and 4: Table of ContentsIntroduction......
Page 5 and 6: Models & OptionsModel TableModelInp
Page 7 and 8: Installation and Mechanical Dimensi
Page 10 and 11: Caution: The PU-E cord should not b
Page 12 and 13: -1 Option WiringThe -1 option board
Page 14: Visual ReferenceENTER (Select) Butt
Page 17 and 18: Software Parameters, cont'dParamete
Page 19 and 20: Parameter 14 - Keypad ModeThis para
Page 21 and 22: Parameter 30 - Signal Input 1 (S1)
Page 23 and 24: Mode 4: Inhibit When UIN1 High (Not
Page 25: Mode 4: Silencing Enabled, Reset On
Page 29 and 30: Application Diagram:Box AMaster Sid
Page 31 and 32: TroubleshootingProblem Possible Cas

MDP Manual - Dart Controls

Create successful ePaper yourself

Delete template?

Save as template?