13517: Harley-Davidson® Motorcycle Siren Model(s) - Whelen ...
13517: Harley-Davidson® Motorcycle Siren Model(s) - Whelen ...
13517: Harley-Davidson® Motorcycle Siren Model(s) - Whelen ...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
®ENGINEERING COMPANY INC.51 Winthrop RoadChester, Connecticut 06412-0684Phone: (860) 526-9504Fax: (860) 526-4078Internet: www.whelen.comSales e-mail: autosale@whelen.comCanadian Sales e-mail: autocan@whelen.comCustomer Service e-mail: custserv@whelen.comInstallation Guide:<strong>Harley</strong>-Davidson® <strong>Motorcycle</strong> <strong>Siren</strong><strong>Model</strong>(s) WS320, WS321Automotive: <strong>Siren</strong>s/SwitchesDANGER! <strong>Siren</strong>s produces extremely loud emergency warning tones! Exposure to thesetones without proper and adequate hearing protection, could cause ear damage and/or hearingloss! The Occupational Safety & Health Administration (www.osha.gov) provides informationnecessary to determine safe exposure times in Occupational Noise Exposure Section 1910.95.Until you have determined the safe exposure times for your specific application, operators andanyone else in the immediate vicinity should be required to wear an approved hearing protectiondevice. FAILURE TO FOLLOW THIS RECOMMENDATION COULD CAUSE HEARING LOSS!Safety FirstThis document provides all the necessary information to allow your <strong>Whelen</strong> product to be properly and safely installed.Before beginning the installation and/or operation of your new product, the installation technician and operator mustread this manual completely. Important information is contained herein that could prevent serious injury or damage.• Proper installation of this product requires the installer to have a good understanding of automotive electronics,systems and procedures.• If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or othervital parts could be damaged by the drilling process. Check both sides of the mounting surface before drillingbegins. Also de-burr any holes and remove any metal shards or remnants. Install grommets into all wirepassage holes.• If this manual states that this product may be mounted with suction cups, magnets, tape or Velcro® clean themounting surface with a 50/50 mix of isopropyl alcohol and water and dry thoroughly.• Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted orlocated in the air bag deployment area will damage or reduce the effectiveness of the air bag, or become aprojectile that could cause serious personal injury or death. Refer to your vehicle owner’s manual for the air bagdeployment area. The User/Installer assumes full responsibility to determine proper mounting location, basedon providing ultimate safety to all passengers inside the vehicle.• For this product to operate at optimum efficiency, a good electrical connection to chassis ground must bemade. The recommended procedure requires the product ground wire to be connected directly to the NEGATIVE(-) battery post.• If this product uses a remote device to activate or control this product, make sure this control is located in anarea that allows both the vehicle and the control to be operated safely in any driving condition. DO NOTATTEMPT TO ACTIVATE OR CONTROL THIS DEVICE IN A HAZARDOUS DRIVING SITUATION.• It is recommended that these instructions be stored in a safe place andreferred to when performing maintenance and/or reinstallation of thisproduct.• FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS ANDINSTRUCTIONS COULD RESULT IN DAMAGE TO THE PRODUCT ORVEHICLE AND/OR SERIOUS INJURY TO YOU AND YOUR PASSENGERS!ACTIVATION OF THISSIREN MAY DAMAGEUNPROTECTED EARS!WearProtection!CAUTIONLoud siren noise can causehearing damage and/or loss.Refer to OSHA Section 1910.95 priorto putting ANY siren into service!For warranty information regarding this product, visit www.whelen.com/warranty©2000 <strong>Whelen</strong> Engineering Company Inc.Form No.<strong>13517</strong>B (050208)Page 1
+12 VDCCUSTOMERSUPPLIEDSPEAKERP/N 01-0860541-00CFUSEREMOVE SCREW TO ADJUST MIC VOLUMEJ1F3 E3 D3F2 E2 D2F1 E1 D1J1C3 B3 A3C2 B2 A2C1 B1 A1(+)12 VoltBattery(-)MICROPHONEP/N 01-0245648-00CMIC / + POS.MIC / - NEG.PTTSHIELDSWITCHES(CUSTOMER SUPPLIED)WAILYELPAIRHORNEND VIEW(CONNECTOR END)PACKARD ELEC. P/N 12040921SUPPLIED BY CUSTOMER.A3C3C1A1F3SHIELDED CABLEE1 P1 J1SUPPLIED BY CUSTOMERD2E2F2F1D1SIRENP/N 01-1081654-00J1 CONNECTIONSPIN # MIN. WIRE GAGE DESCRIPTIONA1A2A3B1B2B3C1C2C3D1D2D3E1E2E3F1F2F318 AWGN/A18 AWGN/AN/AN/A18 AWGN/A18 AWG22 AWG22 AWGN/A22 AWG22 AWGN/A22 AWG22 AWG22 AWGGROUNDNOT USEDSPEAKER +NOT USEDNOT USEDNOT USED+12.5 VDCNOT USEDSPEAKER -AIRHORNPUSH TO TALKNOT USEDMIC (-)MIC (-)NOT USEDYELPWAILMIC (+)SPECIFICATIONSINPUT VOLTAGE12.5 VDC +/-20%INPUT CURRENT @ 15VDC @ 11 OHMS 8 AMPS MAX.INPUT FUSE / CUSTOMER SUPPLIED 10 AMPSSPEAKER IMPEDANCE11 OHMS MIN.OPERATING TEMPERATURE -30 DEG. C. TO +60 DEG. C.STORAGE TEMPERATURE -40 DEG. C. TO +70 DEG. C.HUMIDITY99%SIRENTONESSIREN FREQUENCYMICROPHONEAUDIO BANDWIDTH @ 25 WATTS 300Hz TO 10KHz +/-3dbDISTORTION @ 25 WATTS @ 1KHZ1% MAX.OUTPUT VOLTAGE @ 15VDC @ 11 OHMS 24 V RMS MAX.OUTPUT POWER @ 15VDC @ 11 OHMS 50 WATTSINPUT LEVEL @ R1 MAX. @ 24 VRMS -10db +/-3dbACTIVATION OF THISSIREN MAY DAMAGEUNPROTECTED EARS!WearProtection!CAUTIONLoud siren noise can causehearing damage and/or loss.Refer to OSHA Section 1910.95 priorto putting ANY siren into service!SWEEP RATEWAILYELPPIERCERAIRHORNOUTPUT VOLTAGE @ 15VDC @ 11 OHMSOUTPUT POWER @ 15VDC @ 11 OHMS500 TO 1500 HZ500 TO 1500 HZ500 TO 1500 HZ500 / 1000 HZ34 V RMS MAX.105 WATTS MAX.12 CYCLES PER MIN.180 CYCLES PER MIN.800 CYCLES PER MIN.CONSTANTPage 2
Change language