Initial Checklist - Bel-Aqua Pool Supply, Inc.

More documents

Recommendations

Info

Elevated Suction ApplicationWeld Relay ADC CNT needs to be changed for elevated applications more than 3 ft above the water level.While the system ispowered off, turnon dip switch 7.Re-apply power. Referto page 19 of the servicemanual.VR 1000 VER X.XInitial Start OKPress “OK”.Initial Set-upComplete? Y/NIn this case answer“NO” as we have notset up the system yet.Sol/Mot Delay =120, Change? Y/NAnswer “N”.SU-Pulse Units =50 change? Y/NAnswer “N” to this question.Stratum will attemptto restart.Pinch Limit = 925Change? Y/NAnswer “N”.Enable WeldedRelay Test? Y/NAnswer “Y” to thisquestion. Welded relaytest should always beenabled.Weld Relay ADC =60, change? Y/NAnswer “Y” for elevatedsuction.Set H2O HammerDelay? Y/NAnswer “N” to thisquestion.Power down theStratum. Turn offdip switch 7.Re-apply power to theunit, proceed to“Unprotected Mode” tofill out the Run &Record worksheet.Weld Rly ADC CNT60Use the Up and Down keysto adjust. Increase this# in increments of 20 foreach foot of elevationabove 3 ft. Example:4 ft = 805ft = 1006ft =1207ft = 140Press “OK” to advance to thenext screen.4
Unprotected Mode EntryThe pool is unprotected when in this mode. This mode can be used forvacuuming the pool, backwashing the filter, or when filling out the Run &Record worksheet.VR 1000 Ver X.XInitial start OKPress the “OK” button.Is anyone inPool or Spa? Y/NCheck the pool/spa forswimmers; answer “N” thesystem will now start inunprotected mode.Unprotected PoolVacuum = X.XThis is the operating vacuumof the pool/spa. Thisnumber will be used in theRun & Record worksheet.Initial Set-upComplete? Y/NAnswer “N”, no settingshave been made atthis point.No SwimmersAllowed Pool/SpaNo action necessary.Unprotected ModePress OK to endPressing “OK” will take youout of unprotected mode.The system will stay inunprotected mode for 30minutes. An audible beep willbe heard every 20 seconds.Hayward PoolProductsWhen this screen isdisplayed, press “No”and “Menu” simultaneouslyand hold until the screenchanges to:Unprotected ModeEntry Y/NUnprotected ModeEntry Y/NAnswer “Y”.Press the “OK” button to exitunprotected mode, proceedto “Custom InstallProcedure”. Page 14 servicemanual.Run & Record WorksheetA compilation of vacuum readings for the pool, spa, orpool/spa combo.Pool only—recordthe pool operatingvacuum on the Run &Record worksheet.Now is the best time to returnyour valves to the lowest vacuumreading configuration. This willbe required in “Custom Install”when the following question isasked.Reset 1 st StabOccurred? Y/NProceed to“Custom Install Procedure”Refer to page 17,of the service manual.Put the Stratum into“Unprotected Mode”,allow the pump to gain a full prime.Unprotected PoolVacuum = X.XSpa only—record thespa operatingvacuum on theRun & Recordworksheet.After recording theoperating vacuums ofthe pool and spa, pressthe “OK” button to exitthe “Unprotected Mode”.Pool/Spa combo—placeyour valves into thepool configuration andrecord the operatingvacuum on the R&Rworksheet.Turn your valves to thespa configuration andrecord the operatingvacuum on the R&Rworksheet.Note: The Stratum doesnot have to be shutdown while you changeyour valves.Using the #’s off the Run & Recordworksheet, the highest recordedvacuum will be used when setting the“Hi Vac” for the Stratum. 5” Hgwill be added to the larger numberand rounded down to the nearestwhole number.Ex: 14.2 = 19Ex: 14.8 = 195
Page 1 and 2: Initial ChecklistThings to look at
Page 3: Flooded Suction ApplicationVac Sens
Page 7 and 8: Pinched Line TestCut power to the S
Page 9 and 10: What’s The Problem?Stratum is shu
Page 11 and 12: What’s The Problem?Vac sensor rea

Initial Checklist - Bel-Aqua Pool Supply, Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?