FX-500 Catalog - Panasonic Electric Works Corporation of America

More documents

Recommendations

Info

FX-500PRECAUTIONS FOR PROPER USEWiring• Never use this product as a sensing devicefor personnel protection.• In case of using sensing devices forpersonnel protection, use products whichmeet laws and standards, such as OSHA,ANSI or IEC etc., for personnel protectionapplicable in each region or country.• Make sure that the power supply is OFF while adding orremoving the amplifi ers.• Note that if a voltage exceeding the reted range isapplied, or if an AC power supply is directly connected,the product may get burnt or damaged.• Note that short-circuit of the load or wrong wiring mayburn or damage the product.• Do not run the wires together with high-voltage lines orpower lines, or put them in the same raceway.This can cause malfunction due to induction.• Verify that the supply voltage variation is within the rating.• If power is supplied from a commercial switchingregulator, ensure that the frame ground (F.G.) terminal ofthe power supply is connected to an actual ground.• In case noise generating equipment (switching regulator,inverter motor, etc.) is used in the vicinity of thisproduct, connect the frame ground (F.G.) terminal of theequipment to an actual ground.• Make sure to use the quick-connection cable (optional)for the connection of the controller.Extension up to total 100 m 328.084 ft is possible with0.3 mm 2 or more, cable.However, in order to reduce noise, make the wiring asshort as possible.• Make sure that stress by forcible bending or pulling is notapplied to the sensor cable joint and fi ber cable.DisclaimerThe applications described in the catalog are all intendedfor examples only.The purchase of our products described in the catalog shallnot be regarded as granting of a license to use our productsin the described applications.We do NOT warrant that we have obtained someintellectual properties, such as patent rights, with respectto such applications, or that the described applications maynot infringe any intellectual property rights, such as patentrights, of a third party.Others• This product has been developed / produced for industrialuse only.• The specifi cation may not be satisfi ed in a strongmagnetic fi eld.• The ultra long distance (U-LG, HYPR) mode is morelikely to be affected by extraneous noise since thesensitivity of that is higher than the other modes. Makesure to check the environment before use.• Do not use during the initial transient time (H-SP, FAST,STD: 0.5 sec., LONG, U-LG, HYPR: 1 sec.) after thepower supply is switched ON.• This product is suitable for indoor use only.• Avoid dust, dirt, and steam.• Make sure that the product does not come in contact withoil, grease, organic solvents such as thinner, etc., strongacid or alkaline.• This product cannot be used in an environmentcontaining infl ammable or explosive gases.• Never disassemble or modify this product.• This product adopts EEPROM. Settings cannot be done100 thousand times or more because of the EEPROM'slifetime.17
FX-500DIMENSIONS (Unit: mm in)The CAD data in the dimensions can be downloaded from our website.FX-501(P) FX-502(P)Amplifi erFX-505-C2 FX-505P-C2Amplifi erOutput selection indicator(Yellow) (Note 1)62.5 2.4618.20.323 2 0.079Digital display (Green / Red)9.950.392Output selection indicator(Yellow)8.20.32362.5 2.4612 0.0799.950.392MODE keyOutput 1 operation indicator(Orange) (Note 2)Output 2 operation indicator(Orange) (Note 1)Setting switchMODE keyOutput 1 operation indicator(Orange)Output 2 operation indicator(Orange)Digital display (Green / Red)Setting switchBeamemittingpartBeamreceivingpart100.394321.260281.102 20.87 0.276 0.8195.7 0.22430.118Communication window24 0.945 36.5 1.43775 2.95327.8 1.09422.7 0.894Suitable for 35 mm 1.378 in width DIN railNotes: 1) FX-502(P) only2) FX-501(P): Operation indicator3) FX-501(P): 3-pin, FX-502(P): 4-pin1.1 0.0437 0.27610.50.4133.950.156(Note 3)10Beamemitting0.394partBeamreceivingpartCommunication window27.8 1.09422.7 0.89470.27632281.2601.102 20.87 0.276 0.8195.7 0.224324 0.945 36.5 1.4370.11875 2.953Suitable for 35 mm 1.378 in width DIN railø4 ø0.1576 core cable2 m 6.562 ft10.50.413 9.20.3623.950.1562.8 0.110Note: The shape of setting switch and cable will be changed from productionat the end of November, 2011. Please see drawing below.CN-73-C□ CN-74-C□Main cable (Optional)CN-71-C□ CN-72-C□Sub cable (Optional)• Length LModel No. Length LCN-73/74-C1 1,000 39.370L(Note 2)501.969• Length LModel No. Length LCN-71/72-C1 1,000 39.370L(Note 2)501.969CN-73/74-C2 2,000 78.740CN-73/74-C5 5,000 196.850(Note 1)2.650.1042.540.1002.540.100Notes: 1) CN-74-C□ only2) CN-73-C□: 3-core12( 0.472)10.50.4130.20.00870.276100.39413.60.535ø3 ø0.118 cable14( 0.551) ( )2.90.11430.118100.3946( 0.236)7.20.283CN-71/72-C2 2,000 78.740CN-71/72-C5 5,000 196.850(Note 1)2.650.1042.540.1002.540.100Notes: 1) CN-72-C□ only2) CN-71-C□: 1-core12( 0.472)10.50.4130.20.00870.276100.39413.60.535ø3 ø0.118 cable2.90.11430.118100.39460.23614 0.118( 0.551) ( )( )37.20.283MS-DIN-2Amplifi er mounting bracket (Optional)MS-DIN-EEnd plate (Optional)8.50.3355.20.2050.40.016 ø1.8ø0.0717.50.295 4.2 0.1652-ø3.2 ø0.126 holes3.20.126Material: Cold rolled carbon steel (SPCC)(Uni-chrome plated)21.6 0.85016 0.630352 1.3780.079 20.079271.0635.20.2053.20.126t 1t 0.03950.197100.39430.1182.750.1081.60.063150.591Material: Polycarbonate602.362321.260M3 (length 18 mm 0.709 in) pan head screws30.11824.70.9725.60.220M3 square nut40.157Suitable for 35 mm 1.378 in width DIN rail18
Page 1 and 2: DIGITAL FIBER SENSORFX-500 SERIES V
Page 3 and 4: “Super quality fiber” withstabl
Page 5 and 6: CONCEPTSharp detection with suppres
Page 7 and 8: A variety of functions at the indus
Page 9 and 10: FUNCTIONSelectable interference pre
Page 11 and 12: FX-500SPECIFICATIONSModel No.Type S
Page 13 and 14: FX-500I/O CIRCUIT AND WIRING DIAGRA
Page 15 and 16: LIST OF FIBERSToughFX-500: It is a
Page 17: LIST OF FIBERSToughFX-500: It is a

FX-500 Catalog - Panasonic Electric Works Corporation of America

Create successful ePaper yourself

Delete template?

Save as template?