Muestrario de refacciones Ryobi® - Egomexico

Muestrario de refaccionesRyobi®Intrucciones1. Identifique la figura (Drawing #) de la sección de su interés.2. Identifique el número en la figura (Key #) de la parte que busca .3. Utilice el número en la figura para identificar el número de parte (Part #) en la/spágina/s siguientes.4. Ingrese a www.equiposgraficos.com y complete el formulario de cotizaciónincluyendo el número de parte y descripción.5. Solicite asistencia a cristyg@egomexico.com o al +52(55) 5396 6580Gracias por su compraEFFECTUS GRAPHICUS ORTUS S.A. DE C.V.www.equiposgraficos.comSalónica 259 Col. Sector Naval. México D.F. 02080Tel: +52 (55) 5396 6580

Replacement parts for: RYOBI 2700, 2800, 3200, 3200AN/CD/NP, 3302M, 480/520/560PART # PART #1 231) FILTER FELT P-30201 4.002) GASKET SEAL P-1937 6.703) WICK For oil jar P-1155 1.50PUMP REPAIR KIT - 2700, 2800, 3200P-31120 329.90Consists of: 4 Vanes / 2 Filters / 1 Oil wick /2 Ball bearings / 1 Oil sealPUMP REPAIR KIT - 520/522/530/560P-31130 319.90Consists of: 4 Vanes / 2 Filters / 2 Ball bearings /1 Urethane gasket / 1 Fiber gasket / 8 Paper gaskets /2 Timing belts(Only one of each item depicted here)SUCKER FEETStandard P-5208 .80••• Treated with ink resistant repellent for less ink tracking.SUCKER FEET(A) 500K, 512 P-5241 7.00(B) 480N, 480K P-7580 4.60SHEET SEPARATORBrass P-27114 1.00Copper P-27117 1.20SHEET SEPARATORS(A) 522 P-522114 3.00(B) 522PF / PFH P-522114PF 10.90PUMP VANE••• MADE OF “GROUND STAINLESS STEEL”(27.5 mm x 115 mm) P-9448 69.90THUMB SCREW For sheet separator bracketP-2909 4.20THUMB SCREW For master cylinder tail clamp2700, 2800, 3200 P-2903 8.90TIMING BELT - For main pump520, 522, 530, 560P-3811 34.90VARIABLE SPEED PULLEYP-1491 249.90SPEED CONTROL & FEEDER HAND CRANK••• Improved style works on 2700, 2800, 3200.P-98060 31.90DEA&BCGUIDE SPRING975 PFA P-97471 6.50(Thick) P-33478 10.90(Thin) P-33471 14.00BACK PAPER GUIDE ASSEMBLY2700, 2800, 3200, 3200MCDCOMPLETE P-27081 71.90(A) Screw w/ sems washer P-2328 .60(B) Block P-27221 10.80(C) Bracket P-27090 34.90(D) Back guide spring P-27712 25.80(E) Screw P-2327 .60HOSEFor side blowers P-5265 4.90For compressor filter P-5299 11.20For rear blower P-5288 7.00For sucker tube manifold P-1188 6.00SPRING BASE For P-27088 shown below.P-27100 33.90FEEDER CLAMP5.5 mm slide plate slots P-27087 24.407 mm slide plate slots P-32087 24.40ADJUSTING SCREW P-2652 9.90slide thickness121) BACK PAPER GUIDE P-27537 9.902) SIDE PAPER GUIDE P-27088 10.50PAPER RETAINER - 3302Located under upper feed roller.P-33143 26.90SLIDE PLATE For feeder clamp5 mm slide thickness P-27089 49.906.5 mm slide thickness P-32089 56.90PAPER GUIDE HANDLE STOPPER950, 960 P-95124 14.90SLIDE PLATE & FEEDER CLAMP KITP-39087 83.80BUMPER For air control latchP-5283 3.20PAPER RETAINERFeeder 3302 P-33500 22.50Conveyor .008 thick P-33420 23.90Conveyor .012 thick P-33433 22.50HEIGHT CONTROL SCREW - For paper leveling bar.P-8144 15.90COUPLING JOINT P-6776 12.10SUCKER TUBE P-27174 12.50SCREW HOLDER P-27966 9.10FEED TAPES (sold individually—not in sets)480K/N, 500N/NP P-3935 39.903302 s/n up to 4432 P-3939 32.003302 s/n 4433 to 7036 P-3936 32.003302 s/n 7037 & Up P-3870 39.90FEED SENSING SWITCHR-3302, I-3985 P-4050 29.9013 Solo una muestra de nuestro catalogo www.equiposgraficos.com

ITEK 530, 560, 950, 960, 975.....................................................Continued thru page 16.PART # PART #DBACDFEELER FINGER SHAFTComplete 2700, 2800 P-27138 99.90Complete 3200 P-32138 169.90(A) Shaft only 2700, 2800 P-27139 62.90(A) Shaft only 3200 P-32139 115.90(B) Lever P-27719 19.00(C) Latch P-27141 29.90(D) Roll pin P-2834 .60TAIL CLAMP SPRING P-27327 9.90LATERAL ADJUSTING SCREW For head clampP-2917 13.90SPRING (Plate Cylinder) P-33365 4.90RUBBER FEED ROLLERS2700, 2800 P-27157 179.903200 P-32157 179.90IMP. GRIPPER FINGER1) 2700, 2800, 3200 P-27245 8.002) 3302 (urethane tip) P-33245 14.90TAIL CLAMP2700, 2800 P-27323 105.803200 CD/NP P-32323 116.903200 17-1/4” IMAGE P-32333 110.003302 P-33323 97.5012PAPER STOP FINGER1) 2700, 2800 P-27241 6.002) 3302 P-33241 9.90LOCK PIN on Plate CylinderP-4543 29.90FEED DRUM FINGER P-33237 19.00(urethane tip)SKID ROLLER ASSEMBLY - 3302Operators side (shown) P-33562 134.90Non-operators side P-33568 134.90SPRING - Imp. cyl. latch P-27791 9.50HEAD CLAMPS For Ryobi 3302••• DIAMOND COATED FOR SURE GRIP AND LONGER LIFE.Top bar (shown) P-33788 490.00Short clamp (Operators side) P-33771 162.50Short clamp (Non-operators side) P-33760 162.50ADJUSTING NUT For blanket cylinder clampsRight hand thread P-5303 25.80Left hand thread P-5312 25.80PIN For P-33788 shown above.Ser. # 6186 & lower (3mm small O.D.) P-4773 7.00Ser. # 6187 & higher (5mm small O.D.) P-4789 4.90ABCDSTANDARD BLANKET BARS2700, 2800 Complete P-27252 220.00R-3200, I-975 Complete P-32252 222.00R-3302, I-3985 P-33252 167.90(A) Upper blanket bar 2700, 2800 P-27258 71.90(A) Upper blanket bar R-3200, I-975 P-32258 54.00(A) Upper blanket bar R-3302, I-3985 P-33258 82.00(B) Lower blanket bar 2700, 2800 P-27256 65.90(B) Lower blanket bar R-3200, I-975 P-32256 62.00(B) Lower blanket bars R-3302, I-3985 P-33256 78.90(C) Mounting screw P-2216 .60(D) Clamping screw P-2206 .60WATER CONTROL LEVER3200 MCD P-320416 32.00WAVER ROLLER TENSION SPRINGP-38413 4.90WATER OSCILLATOR SHAFT ASSEMBLY - 2700, 2800Complete P-27460 299.90Shaft only P-27460-S 184.90Dog P-27463 44.00Worm P-27464 63.80Roll pin P-382 .60SPLASH GUARD SHIELD P-27376 3.00SPLASH GUARD KIT P-27376-K 22.90Consists of 2 shields plus hardware.QUICK CHANGE BLANKET BARS••• Bars remain on your cylinder while you make a 5 minute blanket change.Closed cylinder 1/2” gap (19” blanket size)950, 960 / 2700, 2800 P-30310 210.00Open cylinder 4” gap (19-1/2” blanket size)2700XL, 2800XL P-30047 341.25975 / 3200 P-30037 193.05985 / 3200 MCD P-30038 209.65975 / 3200XL,XLD,CPD P-30311 341.253985 / 3302 P-30221 390.00WATER BOTTLE STOP P-7621 8.20SPRING for cap assy. P-27543 4.90BEARING HOUSING P-27322 66.90WATER DUCTOR LATCH2700, 2800 P-27546 6.00Solo una muestra de nuestro catalogo www.equiposgraficos.com14

Replacement parts for: RYOBI / ITEK...................................Continued from page 13.PART # PART #ADJUSTING SCREW For ink fountainR-2700, 2800, 3200, 3302 P-2925 7.00WATER FOUNTAIN ROLLERS2700 P-27364 204.003200 P-32364 390.00OSCILLATING SHAFT ASSEMBLY - INK 2700INK WASH UP BLADE950, 960, 2800 - 30.3 cm Long (6 Holes) P-30224 14.903200, 3302, 3985 - 35.9 cm Long (6 Holes) P-30225 14.90Complete P-27462 204.90Shaft only P-27472 73.80Roll pin P-2834 .60Dog (comes with P-27249) P-27463 44.00Worm (comes with P-27249) P-28464 63.80Dog & Worm set P-27249 94.00INK FOUNTAIN BLADES2700, 950 - 29.5 cm x 9.0 cm (Ser.16331 & up) P-27233 77.902700, 950 - 28.6 cm x 7.0 cm (Ser.16330 & down) P-95233 82.903200 CD/NP - 32.0 cm x 9.0 cm P-32233 89.903200 MCD/MNP- 34.6 cm x 9.0 cm P-32233M 86.00500N / NP - 49.2 cm x 85.7 cm P-50079NP 79.00WASH UP TRAY ASSEMBLY2700/2800 P-27773 219.903200/3202 P-32773 169.903302 P-33773 289.90DOG & WORM KIT P-27874 94.00DOG (Ink & Water 950, 2700) P-27463 44.00WORM (Ink & Water 950, 2700) P-27464 63.80DOG (Ink & Water 960, 2800) P-27463 44.00WORM (Ink 960, 2800) P-27464 63.80WORM (Water 960, 2800) P-28464 63.80BUSHING For ink oscillating rollerP-3203 14.00KEY For drive shaft clutch pulleyP-11652 2.00INK FOUNTAIN WIRE950, 960, 2700, 2800 P-37084 2.903200, 3302 P-32084 1.70BUSHING For ink fountain rollerP-3268 9.90INK IDLER GEAR P-27509 144.90INK DUCTOR ARMS(A) I-950/960 P-95607 43.90(B) R-27/28/3200 Sers. P-27607 43.90INK DUCTOR SPRINGSOperators side P-27338 3.50Non-operators side P-27336 2.40INK RATCHET PAWL P-27268 39.80DRIVE SHAFT AND GEAR ASSEMBLYComplete 2700, 2800 P-27577 289.90Complete 3200 P-32577 340.00Complete 3302 P-33577 243.90Shaft only 2700, 2800 P-27583 143.90Shaft only 3200 P-32583 170.00Shaft only 960PFA, 3200PFA P-32583PFA 199.90Shaft only 3302 P-33583 110.00Gear only 2700, 2800, 3200 (not 3200PFA) P-27581 104.90Gear only 3302 P-33581 110.00Taper pin 2700, 2800, 3200 P-451 .60Taper pin 3302 P-2849 2.00COUNTER P-27954 129.00Screw P-2521 .60Washer P-2700 .60Arm P-27956 26.00IDLER GEARSOn ejector roller P-27636 57.90For C/D drive sprocket shaftP-27629 57.90BUSHING For idler rollers P-3207 24.90GEAR STUD For Chain Delivery drive gearP-7939 16.00ADJUSTING SCREW For ink fountainITEK 950, 960 P-2021 5.20SWITCH BODY For control panelR-3302, I-3985 P-9830 39.9015 Solo una muestra de nuestro catalogo www.equiposgraficos.com

Replacement parts for: RYOBI / ITEK...................................Continued from page 13.PART # PART #OFFSET DUPLICATOR LAMP (Long neck)950, 960, 2700, 2800 P-9865 99.80Lamp comes with plug and can be plugged into anystandard 115v wall outlet. Some models of Ryobi mayneed lamp wired directly to press.••• CAN USE UP TO 100 WATT BULB.GUIDE P-272281 22.00FRONT GUIDE P-272420 83.90B1CA N MGRIPPER BAR ASSEMBLYLED LAMP - On sub control box.R-3302, I-3985 P-9707 30.00CARRIER LINKFor gripper bar P-8738 14.00GRIPPER CHAIN (1 only)59” long P-8939 100.0054” long P-8938 160.00NOTE: Please measure your chains end to end.Chain connecting link P-1540 2.90CONNECTING LINKR-3302, 3304 / I-3985 P-8745 22.50KD E F H U B2G I JO&P&QS RTComplete 2700, 2800 P-270990 439.90Complete 3200 P-320990 399.90Complete 3302 P-330990 495.00(A) Right hand bracket P-320991 52.90(B1) Taper pin P-2810 .90(B2) Taper pin P-2805 .60(C) Gripper arm P-271040 29.90(D) Roll pin P-2832 .60(E) Screw P-2103 .60(F) Gripper finger (no urethane) P-271020 11.50(F) Gripper finger (urethane tip) P-331020 38.85(G) Spring (2 on 2700, 2800, 3200) P-281080 2.30(G) Spring (4 on 3302) P-331080 2.90(H) Set screw P-2511 .60(I) Collar P-1487 9.90(J) Gripper finger shaft - 2700, 2800 P-271060 12.40(J) Gripper finger shaft - 3200 P-321060 10.90(K) Center bracket P-271092 21.90(L) Left hand bracket P-320992 52.90(M) Ball bearing P-1803 6.50(N) C-Ring P-2752 .60(O) Lockwasher P-2702 .60(P) Nut P-2602 .60(Q) Stud P-7920 6.30(R) Roll pin P-2833 .60(S) Gripper pad P-271061 6.40(T) Shaft - 2700, 2800 P-271091 31.90(T) Shaft - 3200 P-321091 34.90(U) Collar P-11435 5.70BACK STOP BRACKET (Chain Delivery)2700, 2800, 3200 P-272422 29.90LDELIVERY TABLE SENSING SWITCHR-3200, I-975 P-9815 18.90V-BELT For Ryobi / ItekFor compressor P-1678 (28”) 8.00For clutch pulley P-1687 (31”) 8.00Motor to pump P-1695 (34”) 7.50Motor to pump 3202M P-4905 (36”) 9.90Motor to pump 950, 960 P-4907 (38”) 9.00Drive motor 3200 (60Hz) P-4910 (42”) 10.50Drive motor 3200 (50Hz) P-4986 (41”) 16.00••• All sizes available 2L, 3L, 4L, 5LDOLLY BOARD ASSEMBLY - RYOBI 3302Complete P-332440 214.00Board only P-332500 174.50Caster P-1641-S 19.90Washer P-569 .60Screw P-10342 .60••• Eliminate costly downtime with your own emergency kitfor your model press.(Master Kit does not include Spring Kit)REPAIR KITS FOR RYOBIMaster kit P-30376 - 513 pcs 239.80Pin kit P-30375 - 168 pcs. 99.90Ring kit P-30374 - 104 pcs. 55.80Nut kit P-30373 - 38 pcs. 21.80Washer kit P-30372 - 68 pcs. 49.90Screw kit P-30371 - 132 pcs. 77.90Spring kit P-31128 - 39 pcs. 129.90• • • • • • • • • PARTS FOR ITEK • • • • • • • •GEAR- For 1015/1117 Plate MakerTank roller frame ass’y. P-1015010 7.50GEAR- For 1015/1117 Plate MakerTank roller frame ass’y. P-1015020 7.50GEAR- For 1015/1117 Plate MakerTank roller frame ass’y. P-1015030 7.50GEAR- For 1015/1117 Plate MakerTank roller frame ass’y. P-1015040 8.70GEAR- For 1015/1117 Plate MakerTank roller frame ass’y. P-1015050 7.00SPRING- For 1015/1117 Plate MakerTension rollers P-1015200 3.90SPRING- For 1015/1117 Plate MakerTension rollers P-1015210 6.90Solo una muestra de nuestro catalogo www.equiposgraficos.com16