Reece ™ | Plumbing | Auspex | Pushfit Manual

INSTALLATION INSTRUCTIONSStep 1Cut the pipe squarely in the middleof the witness mark on the pipeusing secateur type cutters. (Do notuse a hacksaw). This is importantso that when a joint is made, thepipe has penetrated to the full depthof the socket. For pipes that donot have a witness mark, use theWitness Mark Gauge available fromyour supplier.If the pipe is not witness markedand a gauge is not available,measure the depth of the socketand apply your own witness mark tothe pipe. 16mm witness mark length= 24.5mm-20mm witness marklength = 28.00mm.As with any “O” ring joint, theexternal surface of the productin contact with “O” ring will effectthe joint performance. Checkfor imperfections before cutting.The end of the pipe may need tobe freshly cut to ensure smoothpassage for the fitting.IMPORTANT:It is vital that thereis no threat to theperformance of the “O”ring. Check for scratches,sand, mud, etc on pipeor within fitting beforeassembly, as theseconditions mayaffect the integrityof the system.Step 2Ensure the pipe has a square cutand has no rough edges or externaldamage eg. scratches that maydamage the “O” ring.Step 3If the fitting does not have a supportsleeve, insert a SUPPORT SLEEVEpushing fully home.2PERFECT FIT

PRODUCT LISTCouplingsAPPF01161616mm x 16mmAPPF01202020mm x 20mmAPPF02201620mm x 16mmTeesAPPF0316161616mm x 16mm x 16mmAPPF0320202020mm x 20mm x 20mmAPPF0420161620mm x 16mm x 16mmAPPF0420162020mm x 16mm x 20mmAPPF0420201620mm x 20mm x 16mmElbowsAPPF05161616mm x 16mmAPPF05202020mm x 20mmPUSH FIT MANUAL5

PRODUCT LISTLugged Elbow (male)APPF06161516mm Push-Fit x 1/2" male B.S.PAPPF06161520016mm Push-Fit x 1/2" male B.S.Pwith 200mm ExtensionLugged Elbow (female)APPF07161516mm Push-Fit x 1/2" female B.S.PAPPF07202020mm Push-Fit x 3/4" female B.S.PBrazing Tail (male)APPF0816M16mmAPPF0820M20mmBrazing Tail (female)APPF0816F16mmAPPF0820F20mm6PERFECT FIT

Threaded BSP Adaptor (male)APPF09161516mm Push-Fit x 1/2" male B.S.PAPPF09202020mm Push-Fit x 3/4" male B.S.PThreaded BSP Adaptor (female)APPF10161516mm Push-Fit x 1/2" female B.S.PAPPF10202020mm Push-Fit x 3/4" female B.S.PCompression AdaptorsAPPF13161516mm Push-Fit x 15mm copperAPPF13202020mm Push-Fit x 20mm copperAPPF13201520mm Push-Fit x 15mm copperAPPF141616mmAPPF142020mmEnd StopPUSH FIT MANUAL7

PRODUCT LISTAPPF19161516mm Push-Fit x 1/2"APPF19202020mm Push-Fit x 3/4"Loose Nut and Tail (female)AP181616mmAP182020mmBend StabilisersSupport SleeveAPPF231616mmAPPF232020mmDisassembly ToolAPPF3020168PERFECT FIT

Sink SetAPPF11200SESide Entry Sink Sets200mm CentresAPPF11200RARight Angle Sink Sets200mm CentresAPPF11RARight Angle Sink Sets300mm CentresAPPF11SESide Entry Sink Sets300mm CentresCovered by Watermark LN: W185 spec 038Shower SetAPPF12200BERBottom Entry Shower Set 200mmCentres with Copper Riser andLugged ElbowAPPF12200TERTop Entry Shower Set 200mmCentres with Copper Riser andLugged ElbowAPPF12200BECBottom Entry Shower Set 200mmCentresAPPF12200TECTop Entry Shower Set200mm CentresAPPF12BECBottom Entry Shower Set 150mmCentresAPPF12TECTop Entry Shower Set150mm CentresAPPF16BS200BEBottom Entry Bath/Shower200mm CentresAPPF16BS200BERBottom Entry Bath/Shower200mm Centres with CopperRiser and Lugged ElbowCovered by Watermark LN: W185 spec 038PUSH FIT MANUAL9

AUSPEXA division of GSA Industries (Aust.) Pty LtdABN 71 004 784 301PO BOX 4271 Dandenong South Victoria 3164Telephone (03) 9770 3600 Facsimile (03) 9768 3415enquiries@auspex.com.auwww.auspex.com.auA U S P E XC R E AT I V E F L O WA U S P E XC R E AT I V E F L O WAll statements, information and data given herein are believed to be accurate and reliable but are presentedwithout guarantee or responsibility of any kind, expressed or implied, on our part.Neither Auspex nor any of its employees, contractors or agents will be liable in tort, contract or in any other way forany direct or indirect claim, loss, damage, cost, injury or death (“Claim") suffered by any party whether due to anyaction or inaction of Auspex to the extent that the Claim is caused or contributed to by:1. the customer or any other party, including by giving Auspex incorrect or incomplete information or instruction.2. an error in any relevant Australian Standard an event that is otherwise beyond the reasonable control of Auspex