Material Safety Data Sheet - AltaPaints and Coatings

More documents

Recommendations

Info

Product code AT741-9 Date of issue 28 April 2009 VersionProduct name AMERCOAT 741 BLACK8 .Exposure controls/personal protection6.01Name Result ACGIH OSHA Ontario Mexico PPGCement, portland, chemicals TWA 10 mg/m³ 5 mg/m³ R15 mg/m³ TD10 mg/m³ TD 10 mg/m³ NotestablishedSTEL NotestablishedNotestablishedNotestablished20 mg/m³ Notestablished____________________________ ___________ ___________ ___________ ___________ ___________ ___________c.i. pigment black 26 TWA 0.2 mg/m³(as Mn)Notestablished0.2 mg/m³(manganese)0.2 mg/m³(as Mn)NotestablishedSTEL Notestablished5 mg/m³ C5 mg/m³ (asNotestablishedNotestablishedNotestablishedMn) C____________________________ ___________ ___________ ___________ ___________ ___________ ___________glass, oxide, chemicals TWA 10 MG/M3TD15 mg/m3TDNotestablishedNotestablishedNotestablished3 MG/M3 R1 f/cc5 mg/m³(Inhalable)5 mg/m3 R15 mg/m3____________________________ ___________ ___________ ___________ ___________ ___________ ___________1,2,4-trimethylbenzene TWA 25 ppm Notestablished25 ppm 25 ppm NotestablishedSTEL NotestablishedNotestablishedNotestablished35 ppm Notestablished____________________________ ___________ ___________ ___________ ___________ ___________ ___________tetraethyl silicate TWA 10 ppm 100 ppm 10 ppm 10 ppm NotestablishedSTEL NotestablishedNotestablishedNotestablished30 ppm Notestablished____________________________ ___________ ___________ ___________ ___________ ___________ ___________mesitylene TWA 25 ppm Notestablished25 ppm 25 ppm NotestablishedSTEL NotestablishedNotestablishedNotestablished35 ppm Notestablished____________________________ ___________ ___________ ___________ ___________ ___________ ___________ethanol TWA 1000 ppm 1000 ppm 1000 ppm 1000 ppm Notestablished____________________________ ___________ ___________ ___________ ___________ ___________ ___________xylene (mixture of o-, m-, p-isomers)TWA 100 ppm 100 ppm 100 ppm 100 ppm NotestablishedSTEL 150 ppm Notestablished150 ppm 150 ppm Notestablished____________________________ ___________ ___________ ___________ ___________ ___________ ___________Key to abbreviationsA = Acceptable Maximum PeakS = Potential skin absorptionACGIH = American Conference of Governmental Industrial Hygienists. SR = Respiratory sensitizationC = Ceiling LimitSS = Skin sensitizationF = FumeTD = Total dustIPEL = Internal Permissible Exposure LimitTLV = Threshold Limit ValueOSHA = Occupational Safety and Health Administration.TWA = Time Weighted AverageR = Respirable Z = OSHA 29CFR 1910.1200 Subpart Z - Toxic and HazardousSubstancesConsult local authorities for acceptable exposure limits.United States - Canada - MexicoPage: 4/9
Product code AT741-9 Date of issue 28 April 2009 VersionProduct name AMERCOAT 741 BLACK8 .Exposure controls/personal protectionRecommended monitoringproceduresEngineering measuresHygiene measuresPersonal protectionEyesHandsRespiratorySkinEnvironmental exposurecontrols: If this product contains ingredients with exposure limits, personal, workplace atmosphereor biological monitoring may be required to determine the effectiveness of the ventilationor other control measures and/or the necessity to use respiratory protective equipment.: Use only with adequate ventilation. Use process enclosures, local exhaust ventilation orother engineering controls to keep worker exposure to airborne contaminants below anyrecommended or statutory limits. The engineering controls also need to keep gas, vaporor dust concentrations below any lower explosive limits. Use explosion-proof ventilationequipment.: Wash hands, forearms and face thoroughly after handling chemical products, beforeeating, smoking and using the lavatory and at the end of the working period. Appropriatetechniques should be used to remove potentially contaminated clothing. Washcontaminated clothing before reusing. Ensure that eyewash stations and safety showersare close to the workstation location.:::Safety glasses with side shields.: Chemical-resistant, impervious gloves complying with an approved standard should beworn at all times when handling chemical products if a risk assessment indicates this isnecessary.6.01If workers are exposed to concentrations above the exposure limit, they must useappropriate, certified respirators. Use a properly fitted, air-purifying or air-fed respiratorcomplying with an approved standard if a risk assessment indicates this is necessary.Respirator selection must be based on known or anticipated exposure levels, thehazards of the product and the safe working limits of the selected respirator.Personal protective equipment for the body should be selected based on the task beingperformed and the risks involved and should be approved by a specialist before handlingthis product.: Emissions from ventilation or work process equipment should be checked to ensure theycomply with the requirements of environmental protection legislation. In some cases,fume scrubbers, filters or engineering modifications to the process equipment will benecessary to reduce emissions to acceptable levels.9 .Physical and chemical propertiesPhysical stateFlash pointSpecific gravity: 1.75Density ( lbs / gal ) : 14.6: Liquid.: Closed cup: 18.33°C (65°F)Explosion limits : Lower: 2.4%Color: Not available.OdorpHBoiling/condensation pointMelting/freezing pointVapor pressureVapor densityVolatilityOdor thresholdEvaporation rate:::::::::Not available.Not available.>37.78°C (>100°F)Not available.3.1 kPa (23.4 mm Hg)Not available.43% (v/v), 21.35% (w/w)Not available.112 (Butyl acetate. = 1)United States - Canada - MexicoPage: 5/9
Page 1 and 2: Material Safety Data SheetDate of i
Page 3: Product code AT741-9 Date of issue
Page 7 and 8: Product code AT741-9 Date of issue
Page 9: Product code AT741-9 Date of issue

Material Safety Data Sheet - AltaPaints and Coatings

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?