FUTURELIGHT PHW-710 Quick Guide

FUTURELIGHT PHW-710Quick GuideControl BoardMainmenu0 MODE1 LAMP2 SET3 ADJU4 TIME5 EDITSubmenuExtension Display FunctionVALU A001~A511 (AXX) DMX address settingADDRSLAV ON/OFF (SLAV) Slave settingEBOC ON/OFF Change DMX address via externalcontrollerAUTO ALON (AU-A) Automatic Program Run in Stand AloneMAST (AU-M) Automatic Program Run as MasterRUNSOUN ALON (SO-A) Sound-control Program Run in StandAloneMAST (SO-M) Sound-controlled Program Run asMasterVALU D-00 ~ D-30 (DXX) Display the DMX 512 value of eachDISPD-00channelRDIS ON/OFF Reverse displayCLDI ON/OFF Shut off LED displayOPEN ON/OFF Lamp on/offLAAU ON/OFF Lamp on/off/Power switchONLI ON/OFF Lamp on/off via controllerDELA D–00 ~ D-59, D-15 Delay lamp onRPAN ON/OFF Pan ReverseRTIL ON/OFF Tilt Reverse16BI ON/OFF Switch 16 bit/8 bitDEGR 630/540 Select PAN-degreeREST ON/OFF ResetLODA ON/OFF Restore factory settingsVER V-1.0~V-9.9 Software versionLADJ ON/OFF Lamp adjustmentTEST T–01 ~ T–30 Test function of each channelMATI 0000~9999 (hours) Fixture running timeLATI 0000~9999 (hours) Lamp running timeCLMT ON/OFF Service-functionCLLT ON/OFF Clear lamp timeSTEP S–01 ~ S–48 Steps of Program RunSC01 C01 ~ C30 01XX (00~FF)Edit the channels of each scene~30XX (00~FF)SC48 TIME (sec.) T – – X (1~9) Time for each sceneCNIN ON/OFF Edit program via controllerDMX-controlled operationBuilding a serial DMX-chain:Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Alwaysconnect one output with the input of the next fixture until all fixtures are connected.Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120 Ω resistorbetween Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.AddressingThe Control Board allows you to assign the DMX starting address, which is defined as the first channel fromwhich the PHW-710 will respond to the controller.If you set, for example, the address to channel 18, the PHW-710 will use the channel 18 to 34 for control.Please, be sure that you don’t have any overlapping channels in order to control each PHW-710 correctlyand independently from any other fixture on the DMX-chain.If several PHW-710 are addressed similarly, they will work synchronically.Press the Up/Down-buttons for setting the desired starting address. Now you can start operating the PHW-710 via your lighting controller.

DMX-protocolChannel 1 PAN-movement Channel 10 Effect-wheelChannel 2 TILT- movement Channel 11 ZoomChannel 3 PAN/TILT-speed Channel 12 Not occupiedChannel 4 Colour-wheel 1 Channel 13 Shutter, StrobeChannel 5 Cyan Channel 14 DimmerChannel 6 Magenta Channel 15 Lamp, reset, programsChannel 7 Yellow Channel 16 PAN fineChannel 8 CMY and dimmer speed Channel 17 TILT fineChannel 9 CMY colour macrosIn order to call up the different features, you first have to ignite the lamp (control channel 15, DMX-value 64-79) and open the shutter (control channel 13, DMX-value 224-255).Technical specificationsPower supply: 230 V AC, 50 Hz ~Power consumption:1300 WDMX-control-channels: 17DMX-512-connection:3-pin XLRFlash-rate:10 HzColour-system:CMY colour-mixtureColour-wheel:4 dichroic filters plus white, 3200 K and 5600 Kcorrection-filters, UV-filterMaximum PAN-movement 540°:in 3.5 sMaximum TILT-movement 265°:in 2.5 sLength of base (including handles):530 mmWidth of yoke:390 mmHeight (head horizontal):570 mmWeight (net):37 kgMaximum ambient temperature t a:45° CMaximum housing temperature t B(steady state): 80° CMin.distance from flammable surfaces:0.5 mMin.distance to lighted object:0.5 mFuse:T 10 A, 250 VAccessory:OMNILUX OSD 72V/700W G-22 2000h No. 89104005GE CSR 700/2 72V/700W G-22 1000h No. 89105000OSRAM HSR 700 72V/700W G-22 1000h No. 89105010PHILIPS MSR700 72V/700W G-22 No. 89105015PHILIPS MSR700/2 72V/700W G-22 7200K No. 89105016FUTURELIGHT CP-240 controller No. 51834265FUTURELIGHT CP-528 controller 16bit No. 51834315Wizard-512 USB DMX-Software + Interface No. 51860102Wizard-1024 USB DMX-Software + Interface No. 51860110Flightcase for 2x PHS/PHW-700+reel-board No. 51836865FUTURELIGHT DES-3 DMX-terminator 3-pin No. 51834001Please note: Every information is subject to change without prior notice. 11.07.2005 ©