LOCTITE 392™ - Henkel

TDS LOCTITE ® 392, June-2005After 48 hours @ 22 °C, Activator 7380 on 1 sideLap Shear Strength, ISO 4587:Steel :0 gap N/mm² 17.2(psi) (2,500)0.25 mm gap N/mm² 15.8(psi) (2,300)0.5 mm gap N/mm² 14.5(psi) (2,100)Aluminum :0 gap N/mm² 11(psi) (1,600)Zinc dichromate :0 gap N/mm² 11(psi) (1,600)TYPICAL ENVIRONMENTAL RESISTANCEAfter 48 hours @ 22 °C, Activator 7380 on 1 sideHeat AgingHeat aged for 2000 hoursLap Shear Strength, ISO 4587:Steel:@ 93°C N/mm² 13.1(psi) (1,900)@ 121°C N/mm² 9(psi) (1,300)@ 150°C N/mm² 3.4(psi) (500)Humidity ResistanceConditioned in 50°C condensing humidityLap Shear Strength, ISO 4587:Steel:1 week N/mm² 13(psi) (1,900)2 weeks N/mm² 9.3(psi) (1,350)4 weeks N/mm² 3.4(psi) (500)Chemical/Solvent ResistanceAged under conditions indicated and tested @ 22 °C.% of initial strengthEnvironment °C 720 hAir reference 87 100Water/glycol 50/50 87 30Gasoline 87 10Motor oil (MIL-L-46152) 87 100Directions for use1. For best performance bond surfaces should be clean andfree from grease.2. To ensure a fast and reliable cure, Activator 7380 or7387 should be applied to one of the bond surfaces andthe adhesive to the other surface. Parts should beassembled within 15 minutes.3. The recommended bondline gap is 0.1mm. Where bondgaps are large (up to a maximum of 0.5 mm), or fastercure speed is required, Activator 7380 or 7387 shouldbe applied to both surfaces. Parts should be assembledimmediately (within 1 minute).4. Excess adhesive can be wiped away with organic solvent.5. Bond should be held clamped until adhesive has fixtured.6. Product should be allowed to develop full strength beforesubjecting to any service loads (typically 24 to 72 hoursafter assembly, depending on bond gap, materials andambient conditions).Loctite Material Specification LMSLMS dated January-3, 2003. Test reports for each batch areavailable for the indicated properties. LMS test reports includeselected QC test parameters considered appropriate tospecifications for customer use. Additionally, comprehensivecontrols are in place to assure product quality andconsistency. Special customer specification requirements maybe coordinated through Henkel Quality.StorageStore product in the unopened container in a dry location.Storage information may be indicated on the product containerlabeling.Optimal Storage: 8 °C to 21 °C. Storage below 8 °C orgreater than 28 °C can adversely affect product properties.Material removed from containers may be contaminated duringuse. Do not return product to the original container. HenkelCorporation cannot assume responsibility for product whichhas been contaminated or stored under conditions other thanthose previously indicated. If additional information is required,please contact your local Technical Service Center orCustomer Service Representative.Conversions(°C x 1.8) + 32 = °FkV/mm x 25.4 = V/milmm / 25.4 = inchesµm / 25.4 = milN x 0.225 = lbN/mm x 5.71 = lb/inN/mm² x 145 = psiMPa x 145 = psiN·m x 8.851 = lb·inN·m x 0.738 = lb·ftN·mm x 0.142 = oz·inmPa·s = cPGENERAL INFORMATIONThis product is not recommended for use in pure oxygenand/or oxygen rich systems and should not be selected asa sealant for chlorine or other strong oxidizing materials.For safe handling information on this product, consult theMaterial Safety Data Sheet (MSDS).Henkel Loctite Americas+860.571.5100Henkel Loctite Europe+49.89.9268.0Henkel Loctite Asia Pacific+81.45.758.1810For the most direct access to local sales and technical support visit: www.loctite.com