WORKING DOCUMENT - Contact alimentaire

More documents

Recommendations

Info

Article 8Overall migration limit (OML)1. Coated articles for direct food contact shall not transfer their constituents to foodsor the food simulants set out respectively in Annex V in quantities exceeding 60milligrams / 6dm². It should be noted that the test protocols defined for plastics in2002/72/EC and its amendments and other relevant legislation may not beappropriate for all coated articles.EXPLANATORY NOTE3% acetic acid as a stimulant for acidic foodstuffs is inappropriate for both heavy dutycoatings and coatings for light metal packaging due to the fact that a significant partof the substrate can be corroded and contribute to the OML. This is further discussedin Annex VII.2. For coatings for heavy duty articles the OML is expressed in milligrams (ofsubstance)/ Kilogram (of food or food simulant) and may not exceed 60milligrams/ Kilogram food or food simulant.3. For closures, stoppers or similar devices for sealing the overall migration from thecoated surface is expressed in milligrams / kilogram (of food or simulant) andmust not exceed 60 milligrams/kilogram of food or food simulant taking account ofthe analytical toleranceArticle 9Rules for multilayers of coatings for direct food contactIn some instances more than one layer of a coating may be applied to the foodcontact side of the coated article.1. Each coating layer shall comply with the rules given in Articles 3, 4 and 5.2. The SMLs apply to the coated article independent of the coating layer where thesubstance is present.3. The finished article shall comply with the OML16Europäische Vereinigung der Lack-, Druckfarben- und KünstlerfarbenindustrieEuropean Council of Paint, Printing Inks and Artists' Colours IndustryAvenue E. Van Nieuwenhuyse 4 - BE-1160 BrusselsTel:+32 (0)2 676 7480 - Fax: + 32 (0)2 676 7490 - E-mail: secretariat@cepe.org -Internet: http://www.cepe.org/
Article 10Labelling requirements, compliance declaration and record-keeping ofcompliance supporting documentation1. The labelling requirements in Article 15 of the Framework Regulation (EC) No1935/2004 shall apply.2. In the application of Article 16(1) of the Regulation (EC) No 1935/2004, at themarketing stages other than the retail stages, coated materials and articles,coatings and their raw materials shall be accompanied by a written declaration,appropriate to their position in the supply chain.The written compliance declaration shall provide adequate and relevantinformation at each stage of the supply chain to help ensure the suitable use andsafety of the materials and articles subject to the declaration and their compliancewith relevant regulations. The written declaration shall be reviewed regularlyand/or when there is a significant change in the composition of the material andarticle. The declaration of compliance shall contain the following information:a. Name and address of the company which manufactures or imports thefinished material or article;b. Trade name;c. Identity of the raw material, coating or coated article;d. Date of the declaration;e. The confirmation that the material or article complies with, this code ofpractice, the requirements of appropriate EU Regulation and, whenappropriate, of national law under the conditions of use identified undersub-paragraph (g) hereunder. The references of the legislation compliedwith shall be quoted.f. Adequate information relative to the substances used for which specificrestrictions are in place under this Code of Practice and relevantCommunity or national legislation to allow the downstream user to ensurecompliance with those restrictions and list of substances used for which anSML or specifications are established.g. Depending upon their position in the supply chain, specifications on the useof the material or article such as(i)(ii)type or types of food;time and temperature of storage or treatment of the said material orarticle;(iii) surface volume ratio used for compliance assessment.17Europäische Vereinigung der Lack-, Druckfarben- und KünstlerfarbenindustrieEuropean Council of Paint, Printing Inks and Artists' Colours IndustryAvenue E. Van Nieuwenhuyse 4 - BE-1160 BrusselsTel:+32 (0)2 676 7480 - Fax: + 32 (0)2 676 7490 - E-mail: secretariat@cepe.org -Internet: http://www.cepe.org/
Page 2 and 3: ContentsArticle 1Article 2Article 3
Page 9: Article 3Lists of substances author
Page 12 and 13: 4. Substances authorised as direct
Page 14 and 15: 4. In addition to those substances
Page 18 and 19: EXPLANATORY NOTEThe above will be u
Page 20 and 21: ANNEX IOVERVIEW OF HOW COATED FOOD
Page 22 and 23: 4. Conditions of useLarge container
Page 24 and 25: ANNEX IIINCOMPLETE 1 LIST OF MONOME
Page 26 and 27: method with appropriate performance
Page 28 and 29: ANNEX IIIINCOMPLETE 1 LIST OF ADDIT
Page 30 and 31: Lists C and D, including their upda
Page 32 and 33: themselves are of lower molecular w
Page 34: ANNEX IV.III - GENERIC DESCRIPTIONS
Page 37 and 38: Oxirane, ester, -OH, Ar-COOH, R-COO
Page 39 and 40: 10.3 Acid functional polyesters pre
Page 41 and 42: 13. Vinylics13.1 Vinylics prepared
Page 43 and 44: Natural Rubber LatexChemically, nat
Page 45 and 46: Organic solvent and or water free c
Page 47 and 48: ANNEX VIRISK ASSESSMENT FOR MIGRANT
Page 49 and 50: For risk assessments made for foods
Page 51 and 52: To determine the overall migration
Page 53 and 54: Paragraph 5:5. Where a material or
Page 55 and 56: 10. “Food” (or “foodstuff”)
Page 57 and 58: 29. “QMA" means maximal quantity
Page 59 and 60: ANNEX XREFERENCES TO GMP’sFor lig

WORKING DOCUMENT - Contact alimentaire

Create successful ePaper yourself

Delete template?

Save as template?