DS-TISW-F-REV-5-0309 Page 1 - Raychem RPG

Heat Shrinkable Products®TISW-FHeat shrinkable corrosion protection sleeve specifically developed for installationon thrust-secured TIS socket joints or flange couplings that are already inplace.Product descriptionTISW-F Wraparound sealing and protection.Construction: Two-layer system:First layer: Visco-elastic sealant.Second layer: Glassfiber reinforced, radiation cross-linked, polyethylene backing.The TISW-F is a wraparound heatshrinkable sleeve, with a special designed zipper closingsystem, allowing a fast and simple installation.The glassfiber reinforced woven backing givesto the TISW-F a high mechanical resistance as well as a high recovery capacity.TISW-F is installed using standard gas torches. The installation is carried out directly on the cleaned and prepared pipe surface and flange. After preheating,the corrugated cardboard sheet is wrapped around the flange to be sealed.The heat-shrinkable sleeve is positioned centrally over the flange and closed usingthe zipper closure. When heated above 125°C (257°F) the sleeve shrinks tightly around the substrate. During recovery, the adhesive softens and flows to forman intimate bond. The bond strength builds up during cool down and is fully retained after completion of the job.Product features/benefitsBacking with integrated glassfiber reinforcementProvides high mechanical resistance.Provides a high recovery capacity.65% shrinkage ratio – copes with high transitionsReduces inventory logistics & costs.High mechanical resistance backingTISW-F resists abrasion, impact and penetration.No primer requiredNo drying time and easy application.Specially formulated sealantEnsures a strong bond & impervious seal to virtually any substrate.Maintains its elasticity and sealing characteristics over a wide temperaturerange.Product selection guideTISW-FMax operating temperature 30°CCompatible line coatingsPE, PP, FBE, Tape, Coal tar, Asphalt, PlasticsMin preheat temperature 60°CRecommended pipe preparation ST3Sealing adhesive automatically flows and repairs minor mechanicaldamages"Self-healing effect " Saves extra intervention stepsLow preheat sensitivity & proven functionalityAllows easy application combined with high functional performance.Zipper closure systemAllows simple & fast installation.No elaborate equipment requiredMakes installation fast and easy.Keeps installation costs low.DS-TISW- F-RE V-5-0309Product thicknessBacking (as supplied)Backing (fully free recovered)Adhesive (as supplied)TISW-F1.3 mm3.25 mm1.2 mmProduct properties: TISW-FProperty Test method Typical valueBackingBursing strength DIN 30672 3500 NAdhesiveSoftening point ASTM E-28 92°CShear strength EN 12068 @ 10 mm /min. 8 N/cm 2SleevePeel strength EN 12068 @ 10 mm /min. 9 N/cmp 1 of 2

Ordering informationTISW-F type products are available: as a kit, containing:- a sleeve (pre-cut sleeve with zipper closure)Example: TISW-F-DN150/200-425TISW-F Product type Standard ordering optionsDN150/200 Min Pipe diameter in DN / DN100, DN150/200, DN250/300, DN350, DN400/500, DN600, DN700,Max Pipe diameter in DNDN800425 Sleeve width in mm 425 mm , 600 mmFor proper product selection, see latest application table AT-MEPS/MPSM.For proper product installation, see latest installation instruction.DS-TISW- F-RE V-5-0309Berry Plastics warrants that the product conforms to its chemical and physical description and is appropriate for the use stated on the technical data sheet when used in compliance with Berry Plasticswritten instructions. Since many installation factors are beyond the control of Berry Plastics, the user shall determine the suitability of the products for the intended use and assume all risks and liabilitiesin connection herewith. Berry Plastics liability is stated in the standard terms and conditions of sale. Berry Plastics makes no other warranty either expressed or implied. All information contained inthis technical data sheet is to be used as a guide and is subject to change without notice. This technical data sheet supersedes all previous data sheets on this product.Local Distributor / Representative:www.berrycpg.comFor contact details of local Distributors / RepresentativesPlease visit www.berrycpg.com.Headquarters : Berry Plastics Tapes & Coatings Division, Franklin MA, USAFranklin, MA, USATel: +1 508 918 1714US Toll Free: +1 800 248 0149Fax: +1 508 918 1910CPG@berryplastics.comHouston, TX, USATel: +1 713 676 0085US Toll Free: 01 888 676 7202Fax:+1 713 676 0086CPGH@berryplastics.comTijuana, MexicoTel USA +1 858 633 9797Fax US: +1 858 633 9740Tel Mexico: +52 664 647 4397Fax Mexico: +52 664 647 4370CPGTJ@berryplastics.comAarschot, BelgiumTel: +32 16 55 36 00Fax: +32 16 55 36 74CPGE@berryplastics.comBaroda, IndiaTel: +91 2667 264721Fax: +91 2667 264724CPGIN@berryplastics.comp 2 of 2