Superseder II

More documents

Recommendations

Info

FIG4- MEASURING FOR SHORTED TRANSISTORSVOLTMETER. ?2 OHM RES I STORTRANS I STORHEATS I NK?'VI .IA LAMP24V BATTERYALTERNATE EXCITATIONpage 26 - Superseder II - Technical Ha.nual, rev 0
SECTION 5INSTALLATION5.188{CH SPACE.The superseder II system occupies lg" x lr" (49.3 cB x 4g.zcm) of tabre top spece for the charger e.nd 10" x zs" (zs cEX 63.5 cm) for Lhe tenp-plate.Arlor also at least 6" (15.2 cm) of separation from theralr and adjacent equipment, in order Lo maintain properair f low (VITAL!).NorE: operation in dusty or otherwise "dirty" air environmentswill severery reduce the cooring capacity ofthe fens and lead to premature failure.5.2 LINE VOLTAGE.connect the unit to a walr receptacle NEMA 6-30R, 23ov (or208V) wiLh a 30 A!,lP capaciLy.NorE: operation of this unit with e "soft" line or with aIine voltage 10I above or below the nominal 2OAlZSOvAc will resurt in erratic operation and may arsolead to equipment damage if Iarge volLage surgesoccur.5.3 CHANGING LINE VOLTAGE.Ttre superseder I I is normalry wired f or z30v operation.rtre forlowing directions are for changes to 20gv or 11sv.(Refer to figures 5 and 6)5.3. 1 208VAC operation:1) shift.reft red jumper from position 3 to position z.2t shift whiLe lead (from the breaker) from position 6to position 5.3) shift right red junper from position lz to position11.4> shifL shite lead (from the breaker) from position 1sto position 14.NOTE: Line current viII increase by about 10%.5.3.2 11SVAC operation:1) Remove red jumpers (2).2, InsteI first black jumper frou position 1 toposition 43) Instarr first white jumper from position 4 toposition 64, Instalr second black jumper from position 10 toposition 13.Superseder II - Technical Manual, rev O - page ZZ
Page 1 and 2: AIRO QUALITY SALESSUPERSEDER IINI C
Page 3 and 4: CONTEhITSSUBJECTPAGETABLE OF CO}ITB
Page 5 and 6: FIGl-BLOCKDIAGRAT,Iotlq{ toc j;Tl^r
Page 7 and 8: 1.2 THEORY OF OPERATION, CONTROL CI
Page 9 and 10: The flip-flop is started in iLsstat
Page 11 and 12: T.2.4 UONITOR CIRCUIT BOARD.The Mon
Page 13 and 14: The signar input for each of the co
Page 15 and 16: output wirr drop from 11.4v as supp
Page 17 and 18: SEC 2 - VERIFICATION OF PBFORMANCET
Page 19 and 20: 2.T.7 DISCI{ARGE VOLTAGE CUT-OFI"Se
Page 21 and 22: FIG 2 - DPM AND STIITCH CIRCUIT BOA
Page 23 and 24: Frc 3 - gg[r.RgF AtrD IgsISgn crRcu
Page 25 and 26: SEC 4 - TROUBLESHOOTING A},TD REPAI
Page 27: 4.2 FINDING A SHORTED DISCHARGE TRA
Page 31 and 32: FIG 5 - POWER WIRING, 208 I23OVk\.N

Superseder II

Create successful ePaper yourself

Delete template?

Save as template?