fire detection systems fire detection systems - coting.si - coting.si

Recommendations

Info

X-MCPA-KAC ELECTRICAL CHARACTERISTICS ADDRESSABLE LOOP CURRENT LOOP CURRENT (NORMAL) 0,35 mA LOOP CURRENT (FIRE) 3,1 mA OPERATING TEMPERATURE: 0 - 85°C HUMIDITY: 30 - 95% NON-CONDENSING X-MCPA-FLAP ELECTRICAL CHARACTERISTICS ADDRESSABLE LOOP CURRENT LOOP CURRENT (NORMAL) 0,35 mA LOOP CURRENT (FIRE) 3,1 mA OPERATING TEMPERATURE: 0 - 85°C HUMIDITY: 30 - 95% NON-CONDENSING S-MCPA-2470 Pr.Id.:32114 MANUAL CALL POINTS ADDRESSABLE MANUAL CALL-POINT UNIT MECHANICAL CHARACTERISTICS WEIGHT 150 grams DIMENSIONS H: 52 W: 87 D: 87 (mm) WIRE CAPACITY 2 up to 2,5mm FIXINGS surface mount: 4 holes The X-MCPA-KAC manual call point uses a new communication mechanism that gives a typical alarm response time of approximately one second and yet does not use Apollo's patented interrupt bit solution. This new communication system is fully compatible with all our addressable modules, SAM's, S90, XP95 and Discovery detectors. Like Apollo's interrupt based system, the more call points on a loop, the longer the time from activation to alarm. Pr.Id.:32526 ADDRESSABLE MANUAL CALL-POINT UNIT (LOW-PROFILE) Both the MCPA-KAC and the MCPA-FLAP are addressable manual callpoints, compatible with a version of the meter bus protocol used by several panel manufacturers, used for signaling an emergency or fire situation to an addressable fire detection control panel. The main features of these units are their low quiescent power consumption and low cost. An 8 way DIL switch is used for setting the address of the unit within the communication loop. Addresses 0 to 125 can be programmed in binary code, where a switch in the “OFF” position represents a “0”. This unit returns an analog value of 16 when the glass is intact and a value of 64 when the glass panel has been pressed. The unit is provided with a bi-color LED which signals with a green light flash when the unit is being interrogated by the control panel. When in ALARM, the LED is illuminated in red by command of the control panel. Pr.Id.:32116 MECHANICAL CHARACTERISTICS WEIGHT 80 grams DIMENSIONS H: 28 W: 120 D: 80 (mm) WIRE CAPACITY 2 up to 2,5mm FIXINGS surface mount: 2 holes CONVENTIONAL MANUAL CALL-POINT UNIT (LOW-PROFILE) ELECTRICAL CHARACTERISTICS MECHANICAL CHARACTERISTICS QUIESCENT DC CURRENT 40 µ A WEIGHT 80 grams FIRE CURRENT 20 mA DIMENSIONS H: 52 W: 87 D: 87 (mm) OPERATING TEMPERATURE 0 - 85°C WIRE CAPACITY 2 up to 2,5mm HUMIDITY 30 - 95% NON-CONDENSING FIXINGS surface mount: 2 holes The S-MCPC-2470 is a conventional manual call-point compatible with all conventional fire alarm control panels. The main feature of this unit is the use of a bi-color LED to signal the operational status of the call-point. The included LED blinks regularly with the green color while connected to a detection zone and lights with a permanent red light when activated, (alarm condition). This, allied with its very competitive price and aesthetic appearance , make the S-MCPC-2470 a very attractive product. 11
SOUNDERS FEATURING LOW POWER CONSUMPTION & HIGH SOUND OUTPUT 1 2 3 4 5 6 7 8 ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF X-VIPER - A X-VIPER - A CHARACTERISTICS STANDARD SHADOW SUPPLY VOLTAGE: 17-40 V DC 17-40 V DC CURRENT CONSUMPTION QUIESCENT: 1 mA 1 mA CURRENT CONSUMPTION ALARM: 6 mA 6 mA HIGH FREQUENCY SOUND: 11 mA 11 mA ADDRESS RANGE: 94 - 125 (32/Loop) SHADOW (64/Loop) PROGRAMMING DATA FOR ADDRESSABLE BASE SOUNDER SWITCHES 1-5: REGULAR ADDRESSES FROM 094 TO 125 IN BINARY SWITCH 6: OFF: IAS LOOP SOUNDER ON: APOLLO SOUNDER CIRCUIT CONTROLLER SWITCH 7 & 8: OFF: SWEEP SOUND (800 - 1000 Hz) SWITCH 7 ON & 8 OFF: ALTERNATE SOUND (2800 - 3500 Hz) SWITCH 7 OFF & 8 ON: ALTERNATE SOUND (800 - 1000 Hz) SWITCH 7 & 8: ON: CONTINUOUS (800 Hz) X-VIPER SE CHARACTERISTICS X-VIPER - BEACON CHARACTERISTICS ADDRESSABLE SOUNDERS Pr.Id.:32532 VIPER ADDRESSABLE SOUNDER WEIGHT: 153 grams DIMENSIONS: DIAMETER: 100 - HEIGHT: 85 (mm) SOUND OUTPUT: 85dB @ 1 METRE (92dB High Pitch) TONES: 4 TONES SELECTED BY DIL SWITCH PROTECTION RATING: IP65 __ ++ ++ _ __ __ CONNECTION DIAGRAM WEIGHT: DIMENSIONS: CONTINUOUS TONE: RAMP TONE: BI-TONAL BI-TONAL 1 2 3 4 5 6 7 8 Also exists in SHADOW version (see BASE SOUNDER) VIPER ADDRESSABLE SOUNDER - SPECIAL EDITION WEIGHT: 125 grams DIMENSIONS: DIAMETER: 100 - HEIGHT: 85 (mm) SOUND OUTPUT- CONTINUOUS85 dB @ 1 METRE SOUND OUTPUT- SWEEP: 85 dB @ 1 METRE SOUND OUTPUT- ALTERNATING: 85 dB @ 1 METRE SOUND OUTPUT- HIGH PITCH: 92 dB @ 1 METRE VIPER ADDRESSABLE SOUNDER & BEACON X-VIPER BEACON This addressable sounder is a surface mountable unit available in red and white colors with very low power consumption as its main characteristic. It has a sound output of up to 92dBA with less than 5mA power consumption @ 24V. It is possible to place up to 96 sounders or 64 sounder/beacons in a single loop, 32 of which can be given a response address, the remaining being shadow sounders. Pr.Id.:32529 STANDARD SHADOW SUPPLY VOLTAGE: 17-40 V DC 17-40 V DC CURRENT CONSUMPTION QUIESCENT: 0.8 mA 0.8 mA CURRENT CONSUMPTION ALARM: ADDRESS RANGE: 3.5 mA 3.5 mA 94 - 125 (32/Loop) + SHADOW (64/Loop) TONES: 4 TONES SELECTED BY DIL SWITCH PROTECTION RATING: IP65 This addressable sounder is a surface mountable unit available in red and white colors with very low power consumption as its main characteristic. It has a sound output of up to 92dBA with less than 5mA power consumption @ 24V. It is possible to place up to 96 sounders or 64 sounder/beacons in a single loop, 32 of which can be given a response address, the remaining being shadow sounders. Pr.Id.:32531 X-VIPER - A - SE SUPPLY VOLTAGE: 17-40 V DC CURRENT CONSUMPTION QUIESCENT: 1 mA CURRENT CONSUMPTION ALARM: 4.5 mA ADDRESS RANGE: 94 - 125 (32/Loop) TONES: 4 TONES SELECTED BY JUMPERS PROTECTION RATING: IP44 175 grams DIAMETER: 100 - HEIGHT: 70 (mm) 1000Hz 800 - 1200Hz 1000 - 1300Hz 2000 - 2600Hz This addressable sounder/beacon, is a surface mountable unit available in red color with very low power consumption as its main characteristic. It has a sound output of up to 92dBA with less than 5mA power consumption @ 24V. This includes a high power LED based beacon which uses 8 super-high efficiency RED LED's. It is possible to place up to 96 sounders or 64 sounder/beacons in a single loop, 32 of which can be given a response address, the remaining being shadow sounders. The beacon operation can be chosen between two modes: Mode A: The beacon operates simultaneously with the sounder and stops with the silencing. Mode B: The beacon operates simultaneously with the sounder but does not stop flashing until the loop is 12
Page 1: FIRE DETECTION SYSTEMS Product cata
Page 4 and 5: RAIK Pr.Id.:30100 1-3 loops analogu
Page 6 and 7: 1, 3 LOOP Juno-NET 100 Pr.Id.:30109
Page 8 and 9: J-NET-LOOPCON CHARACTERISTICS DIMEN
Page 10 and 11: or many fire alarm systems, all tha
Page 14 and 15: X-VULCAN CHARACTERISTICS STANDARD S
Page 16 and 17: X-IN X-I/O X-IN ELECTRICAL CHARACTE
Page 18 and 19: X- X-LSCISO TECHNICAL CHARACTERISTI
Page 20 and 21: X-IND CHARACTERISTICS WORKING VOLTA
Page 22: ACCESSORIES, GAS DETECTORS Air Samp

fire detection systems fire detection systems - coting.si - coting.si

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?