Supply Pumps - Zycon

Monark ®Pneumatic 2-Ball Piston PumpsPresident/Monark Typical Fluids Handled• Solventborne and waterborne fluids• High solids, plural component coatings• Resins• Stains, lacquers and varnishes• Cleaning fluids• Acid-catalyzed materials• High solid coatingsTechnical Specifications and Ordering InformationPUMP SPECIFICATIONSINLET/OUTLETMANUALSPart Number 218763 223186 224350 224343 224345 218956 239327 223844 223596 237958Model 1.5:1 2:1 5:1 5:1 5:1 5:1 15:1 15:1 23:1 23:1Output per cycle 429 cc 343 cc 157 cc 157 cc 157 cc 135 cc 44 cc 44 cc 27 cc 27 ccMaximum workingpressure psi (bar, MPa)Maximum air inputpressure psi (bar, MPa)180(12, 1.2)120(8. 0.8)200(12, 1.4)100(7, 0.7)900(62, 6.2)180(12.4, 1.2)600(42, 4.2)120(8, 0.8)900(62, 6.2)180(12.4, 1.2)900(62, 6.2)180(12.4, 1.2)2700(186, 18.6)180(12.4, 1.2)2700(186, 18.6)100(7, 0.7)3450(238, 23.8)150(10, 1.0)2760(190, 19.0)120(8, 0.8)Output at 60 CPM gpm (lpm) 6.8 (25.7) 5.4 (20.5) 2.5 (9.4) 2.5 (9.4) 2.5 (9.4) 2.1 (8.1) 0.7 (2.6) 0.7 (2.6) 0.4 (1.6) 0.4 (1.6)Pump inlet size 1-1/2 npt(f) 1-1/2 npt(f) 1-1/5 (f) 3/4 npt(f) 3/4 npt(f) N/A 3/4 npt(m) 3/4 npt(m) 3/4 npt(m) 3/4 npt(m)Pump outlet size 1 npt(f) 1 npt(f) 3/4 npt(f) 1/2 npt(f) 1/2 npt(f) 3/4 npt(f) 3/8 npt(f) 3/8 npt(f) 3/8 npt(f) 3/8 npt(f)Pump manual assembly 307653 307985 308118 308116 308117 307044 308739 308106 307619 307619Lower manual 307652 307983 308118 308116 308117 307044 306981 308106 307619 307619Motor manual 307141 307043 307043 307043 307043 307043 307043 307043 307043 307043Type Seals 1.5:1 2:1 5:1 5:1 5:1 5:1 15:1 15:1 23:1 23:1PUMP ConstructionCarbon Steelstainless steelStubby UHMWPE/Leather 223186 239327 223596Drum UHMWPE/Leather 223185PTFE 218956Stubby UHMWPE/Leather 218763 237958UHMWPE/PTFE 224343UHMWPE/Neoprene 224345PTFE/Leather 223844Drum UHMWPE/PTFE 224350Accessories206220 Wall BracketFor mounting President pump to wall.207365 Wall BracketFor mounting a President pump to a wall.205640 Pump Floor StandFor mounting a President pump in a suction feed system.Adapter 206108 is required.205700 Pump Floor StandFor mounting a President pump in a suction feed system.220581 Pump Floor StandFor mounting a President pump in a suction-feed system.194248 Accessory Packing ToolEases insertion of piston assembly into cylinder.168085 Accessory Assembly ToolUse to install piston assembly into cylinder (model 239326).171818 Adjustment ToolA 0.145 in (3.7 mm) gauge used to ensure proper clearancebetween the poppets and the piston on the President air motor.207579 Padded PliersFor servicing President air motor trip rod.236054 Suction Kit (Monark 1.5:1 and 2:1 only)Use to siphon material out of 55 gal (200 l) closed-end drum.Includes siphon tube, bung adapter, 6 ft (1.8 m) nitrile hose, 1-1/2npt(m) outlet fitting.207484 Siphon Kit, Aluminum (Monark 5:1 only)Use to siphon fluid from a 5 gal (18.9 l) pail. Includes nylon suctionhose 214960, 3/4 in ID, 3.5 ft (1.1 m) long, 3/4 in npt(f) swivel outletfitting.208259 Siphon Kit, Carbon Steel (Monark 5:1 only)Use to siphon fluid from a 55 gal (200 l) drum. Includes nylon suctionhose 214961, 3/4 in ID, 6 ft (1.8 m), 3/4 in npt(f) swivel outlet fitting,bung adapter.208920 Siphon Kit, Aluminum (Monark 5:1 only)Use to siphon fluid from a 5 gal (18.9 l) pail. Includes nylon suctionhose 170706, 1 in ID, 4 ft (1.2 m) long, 3/4 in npt(f) swivel outletfitting, inlet strainer.