39a

Red Lion Deluxe Counters, Timers & Rate Meters• Bi-Directional Counting to 20 kHz• 8 Counting & Timing Modes• Programmable Scaling• Eight Digit, 0.46" (12 mm) LCD• Green/Red LED BacklightChanges at Setpoint• NEMA 4X/IP65 FrontCUB5• Setpoint Relay Output Option• RS232 or RS485 CommunicationsSPECIFICATIONSCounter A: 8 digit display, -9999999 to 99999999Counter B: 7 digit display (positive only)Count Rate: 20 kHz max. at 50% duty cycle, except Dual = 16kHz, Quadrature = 14 kHz, Quadrature x4 = 13 kHzRate Meter: 6 digit display, with R designator on leftFrequency: 20k Hz max., 0.01Hz min., Accuracy 0.01%Count/Rate Input A: Source, Sink, Logic, Mag pickup; DIP switch selectableCurrent Sinking: Internal 7.8 kΩ pull-up to + supplyCurrent Sourcing: Internal 3.9 kΩ pull-down, 7 mA max. @ 28 VDC.Logic Input: VIL = 1.25 V max.; VIH = 2.75 V min.; VMAX = 28 VDCMagnetic Pick-up: Sensitivity 200 mV peak, 100 mV hysteresis,Maximum input ±40 V peak, 30 VrmsCount/Rate Input B: Logic signals onlyTrigger levels: VIL = 1.0 V max; VIH = 2.4 V min; VMAX = 28 VDCCurrent sinking: Internal 10 kΩ pull-up resistor to + supplyFilter (LO Freq.): Damping capacitor for switch contact bounce. Limitsinput to 50 Hz max. & pulse widths to 10 msec min.Timer:7 digit display, with t designator on leftResolution: Selectable 0.001 sec to 1 hr, Accuracy 0.01%Cycle Counter: 6 digit display, with C designator on leftRate:10 Hz max. except Input B is 500 Hz with filter offTimer/Cycle Inputs: Logic Inputs, Current Sinking (active low)Pulse Width: 1 ms min.Software Filter: 50 msec start/stop debounce delay when enabledUser Input: Programmable function inputLogic Input, Current Sinking (active low)Display:Reflective LCD with full viewing angle or selectabletransmissive red/green backlight LED (display colorchanges at preset when using relay module)Power (not isolated): 9-28 VDC @ 30 mA max. from Class 2 supplyLED Backlight: Adds 95 mA to supply currentTemperature: -35 to 75 °C operating @ min. backlight (35 °Cmax. at max. backlight),

Simpson 1/8 DIN Counter Totalizer, Rate/Totalizer/Batch▲To Order—Insert Number Code for Each Letter to SelectCatalog Number. Order Example: S664-1-1-0-0-0ABCDEFS664• NEMA-4X Front Panel• Four Frequency Ranges Available (99 Hz, 999 Hz,9 kHz, 35 kHz)• Easy to Use (Install/Wire/Mount, Select Range, and Go)• Bright Red LEDs for Easy Viewing• Minimum Mounting Depth Required• 120 or 240 VAC• Optional Excitation Output 12 VDC @ 100 mA• Modular Design• Screw Terminals for Easy InstallationSPECIFICATIONSDisplay Type:7 segment, bright red LED, 0.56" HPower:120/240 VACOperating Temp: 0 to 55°CSize:3.6" W x 1.8" H x 3.24" D (92 x 48 x 82 mm)ORDERING INFORMATIONA – B – C – D – E – FBasic UnitS664 Frequency CounterPower Supply1 120 VAC2 240 VACInput Type1 Standard Pulse Input2 Quadrature inputOutput Type0 NoneExcitation Output0 None1 12 VDCOther0 None▲ S660• NEMA-4X Front Panel• Uses Words, Not Symbols for Easier Programming• Bright Red LEDs for Easy Viewing• Large, Tactile Buttons Can Be Pressed with Gloves On• Standard 1/8 DIN Cutout• Up to Two 5 Amp Relays Optional• Optional Excitation Output 12 VDC• Screw Terminals for Easy InstallationTo Order—Insert Number Code for Each Letter to SelectCatalog Number. Order Example: S660-1-2-2-1-0ABCDEFSPECIFICATIONSDisplay Type: 7 segment, bright red LED, 0.56" HPower:120/240 VACOperating Temp: 0 to 55°CNMRR:60 dB @ 50/60 HzSize:3.6" W x 1.8" H x 3.24" D (92 x 48 x 82 mm)ORDERING INFORMATIONA – B – C – D – E – FBasic UnitS660 Preset Up/Down CounterS661 Preset Rate CounterS662 Preset Totalizing/Batch CounterS663 Preset Totalizing/Rate CounterPower Supply1 120 VAC2 240 VACInput Type1 Standard Pulse Input2 QuadratureOutput Type0 None1 1 Mechanical Relay2 2 Mechanical RelaysExcitation Output0 None1 12 VDCOther0 NoneDIGITALMETERS40

ATC Westcon CountersW3830 Series6-Digit Indicator/Totalizer with Optional OutputsW3870 Series6-Digit Frequency Input Indicator/Totalizerwith Optional OutputsDIGITALMETERS• Automatic Square RootExtraction• Logic Controlled Up/DownCounterFEATURESSPECIFICATIONS• Preset Up Counter• Preset Down Counter• FLUME 5/2 Calculation• WEIR 3/2 CalculationMODEL: RANGE: ACCURACY:3830-23 0-5 VDC ±0.08% reading, ±0.05% FS3830-25 0-10 VDC ±0.08% reading, ±0.05% FS3830-27 4-20 mA ±0.08% reading, ±0.05% FSOPERATING TEMP: 0°C to 50°C (32°F to 122°F)FRONT/CASE: NEMA 4X / Anodized AluminumOption C:Option H:Option P:Option T:Option V:OPTIONAL OUTPUTS3 Form-C 5 amp relay outputs activate whenprogrammable high and low limits are exceeded.Permits on-off control of external circuitry, or alarmstatus communication with other equipment.1-4 analog outputs, 0-5 VDC, ±5 VDC, 0-10VDC or4-20 mA. Accuracy is 0.35% of scaled range. Outputsignals are proportional to meter display.Excitation 10VDC & 24VDCRS232C serial data communications interface at9600 Baud rate.Totalizer pulse output. Solid-state relay (SSR).Operating range: ±80V peak. continuous load current:150 mA. Pulse width: 60mS (consult factory if fasteroutput is required).RANGE: User programmabledecimal, scale factors andinsignificant zero blanking yielda display range of 0.00001 to999999.INPUT RESPONSE:0.0005 to 99,999 HzPROTECTION: ±200 V peakSENSITIVITY: TTL, CMOS orcontact compatibleSPECIFICATIONSOPTIONAL OUTPUTSPULSE WIDTH: 5 micro- secondsminimumTRIGGER MODE: Negative edgeof input pulseINPUT IMPEDANCE: 12k ohmsFILTER/DEBOUNCE:Front panel programmabledigital filterFRONT/CASE:NEMA 4X / AnodizedAluminumOption C: 3 Form-C 5 amp relays activate when programmable highand low limits are exceeded. Permits on-off control ofexternal circuitry, or alarm status communication withother equipment.Option G: Input amplifier, 30 mV peak input at 5 Hz to 99,999 Hz.Option H: 1-4 analog outputs, 0-5 VDC, ±5 VDC, 0-10VDC or 4-20 mA.Accuracy is 0.35% of operating range. Output signals areassignable to rate and total.Option P: Excitatin 10VDC & 24VDCOption S: 230 VAC Power.Option T: RS232C serial data communications interface at 9600Baud rate.Option X: Screw terminal block connector. Accepts up to#14 AWG wire.41ORDERING INFORMATIONModel #: 3830 - XX XXXXInput23 0-5 VDC25 0-10 VDC27 4-20 mAOptionsC 3 RelaysH1 1 Analog OutputT RS232V Totalizer Pulse OutputP ExcitationPRICE Model #:$ 225$ 6065140N/C6026ORDERING INFORMATIONOptionsCGH1STXP3870 - XXXXXXRelay OutputsInput Amplifier1 Analog Output230 VAC PoweredRS232Screw TerminalExcitation

KEP Counters & TimersKAL-D06 8 Digit Electronic Counter• Low speed input for contactclosures• High speed input sinks 18V max• Optional quadrature & highvoltage inputs• 10 year lithium battery –no external power needed• NEMA 4X (IP65) front• UL recognizedDisplay:Readout:Reset:Backlight:Hi-speed Input:Lo-speed Input:Quadrature Input:Reset Input:Direction Input:Hi-voltage Input:Hi-voltage Reset:Temperature:Case:SPECIFICATIONSLCD, digits 0.35" (9mm) high8 digits with leading zero blankingPanel or external (can be disabled)Requires external 5V supply (20 mA)NPN sink; 18V, 10kHz maxNPN sink or contact closure; 18V, 30Hz maxNPN sink or push pull, 18V, 2.5kHz max>15ms NPN sink or contact closure; 18V maxNPN sink or contact closure; 18V max (Lo=down)Count 10 pulses/sec max; opto-isolated 250VAC/120VDC max>15ms, opto-isolated 250VAC/120VDC max-10 to 60°C operating24 x 48 x 52 mmDIGITALMETERSKAL-DTIME 8 Digit Electronic Timer• Electronic or contact closure input• Powered by 10 yearlithium battery• High voltage inputoptional• NEMA 4X (IP65) front• UL ListedDisplay:Readout:Reset:Backlight:Timing Input:Reset Input:Direction Input:Hi-voltage Input:Hi-voltage Reset:Temperature:Case:SPECIFICATIONSLCD, digits 0.35" (9mm) high8 digits with leading zero blankingSECONDS: 99999999MINUTES and SECONDS: 99999-59HOURS and 1/100ths: 99999-99HOURS and MINUTES: 99999-59Panel or external (can be disabled)Requires external 5V supply (20 mA)NPN sink, negative edge trigger; 18V max>15ms NPN sink or contact closure; 18V maxNPN sink or contact closure; 18V max (Lo=down)Opto-isolated 250VAC/120VDC max>15ms, opto-isolated 250VAC/120VDC max-10 to 60°C operating24 x 48 x 52 mm924K Counter, Rate Meter & Timer• Displays actual value,presets, batch countor total count• 3 predefined parametersettings• Tracking presets• 4 stage RESET modes• 2 relay outputs• 3 stage key lockoutSPECIFICATIONSDisplay:2 line, 6 digit red LCDCount Inputs: NPN/PNP, 5kΩ, 55 kHz maxSwitching Level: Low=0-4 VDC, High=12-30 VDC (924KA)Count ModesPulse: cnt.dir, up.dn, up.up, quad, quad 2, quad 4,A/B, (A-B)/A x 100%Frequency: A, A-B, A+B, quad, A/B, (A-B)/A x 100%Timer:FrErun, Auto, InpA.InpB., InpB.InpB.Monitor/Reset Inputs: MPI, lock, gate, resetPulse Duration: 10 ms/1 ms min.Relay 1:Form A, programmable NO or NCRelay 2:Form CMax. Switching: 250 VAC / 110 VDC, 3 A, 750 VA / 90 WSensor Supply: 24 VDC, 80mATemperature:-20 to +65 °C operatingProtection:IP65 (front)Case:1/8 DIN (48 x 48 x 107mm)KAL-D06KAL-DQUAD06KAL-D06AC/DC8 digit counter with 10 yr battery8 digit counter with 10 yr battery& Quadrature Input8 digit counter with 10 yr battery& High Voltage InputORDERING INFORMATIONKAL-DTIMEKAL-DTIMEAC/DC924KA*924KB*8 digit timer with 10 yr battery8 digit timer with 10 yr battery& High Voltage InputCounter, Rate, Timer; 90-260 VAC powerCounter, Rate, Timer; 10-30 VDC power*Add suffix 0 for relay outputs, 1 for opto-coupler outputs42

KEP Counter/TimerLCD preset add/subtract counter,timer, frequency meter903K/904K Series• 6-Digit Counter, Timer orFrequency Meter• 2 Preset Values(Type 903K 1 Preset)• Input Scaling(0.0001 to 9.9999) Multiplier• 2-Line LCD Display• Count and Preset Rangeof -999999 to 999999• Add or Subtract Count Control• AC or DC Operation• Secondary Preset Batch Counter (904K)• 24 VDC to Power PeripheralsDisplay:Preset:Supply voltage:Housing:Protection:Power Supply:ORDERING INFORMATIONTo Order—Insert Number Code for Each Letter to Select Catalog NumberOrder Example: 904K-A-0-AA – B – C – DABCDBasic Unit903K Single Output904K Dual OutputsInput VoltageA 115 VACB 230 VACC 11 to 30 VDCD 24 VACE 48 VACOutputs0 Relay1 Opto-Isolated collector and emitterOptions— Blank if NoneA Backlit LCD Display (904K only)▲ 904KSPECIFICATIONS6-digit, 2-line, 7 segment LCD with signType 904 two preset valuesType 903 one preset value115 VAC, 230 VAC, 48 VAC or 24 VAC(tolerance ± 10%) or 11 to 30 VDC48 x 48 mm DINIP 65 (front)24 VDC, 80 mAKEP Totalizer/Rate MeterRatemeter/totalizer/processmonitor from analog inputs▲ INT69RTIntellect-69 Series• High/Low Scaling from Front Panel• 2 Set Points Assignable To Rate or Total• Display Rate (Pressure, Level, Watts, Etc.),Peak and Valley and Integrated Total• 0–5V, 0–10V, 1–5V, 4–20 mA or 0–20 mA Analog Input• NEMA 4X/IP 65 Front Panel• +24V Output for Peripherals• RS-422/RS-232 Serial Communications• 4–20 mA Output• Square Root Extraction• Optional Rate Per Day FeatureORDERING INFORMATIONTo Order—Insert Number Code for Each Letter to Select Catalog Number.Order Example: INT69RT-A-L-1-A-C1A – B – C – D – EABCDEBasic UnitINT69RT Ratemeter/TotalizerINT69R Ratemeter OnlyINT69PM2 Process MonitorDisplays from -19999 to +49999INT69T Totalizer OnlyOperating VoltageA110 VAC ±15% or 12 to 24 VDCB220 VAC ±15% or 12 to 24 VDCInputs— Blank for INT69PM2LLinear (standard)SSquare Law (optional)Control Outputs1 2-Open Collector Outputs (standard)2 2–10 Amp Form C Relays (optional)Options (Multiple Options Available)AAnalog Output (4–20 mA)DRate per Day, Hour or MinuteC1RS-232 communicationsC2RS-422 communications42a

MINItrol Series• CSA Approved• Separate Scaling Factors for A and B Inputs• Display Rate and Total• Pulse Input—10 kHz Maximum• Security Lockout• RS-422/RS-232 Serial Communication• NEMA-4X/IP65 Front Panel• Separate Add/Subtract Simultaneous Inputs• Quadrature and U/D Direction Control Inputs• 30 mV Magnetic Pickup Inputs• 4–20 mA or 0–20 mA Analog OutputORDERING INFORMATIONTo Order—Insert Number Code for Each Letter to Select Catalog Number.Order Example: MRT-A-3-142bKEP Totalizer/Rate MeterLow Cost, Pulse Input,Totalizer & RatemeterA – B – C – D▲ MRTA Basic UnitMRT 6-Digits, Counter/RatemeterMC2 6-Digits, Counter OnlyMR2 5-Digits, Rate OnlyB Operating VoltageA 110 VAC ±15% or 12 to 15 VDCB 220 VAC ±15% or 12 to 15 VDCC 24 VAC ±15% or 12 to 15 VDCC Count Inputs3 Standard, 4–30 VDC Simultaneous Inputs3M Mag. Input, Input A Only,30mV Input (Input B, 4–30V)3MB Mag. Input, Inputs A and B, 30 mV input5 4–30V Pulses on Input A,4–30V Direction Control Input on Input B5M 30 mV Pulses on Input A,4–30V Direction Control Input on Input B9 Quadrature, Accepts 4–30V Pulses9MB Quadrature, Accepts 30 mV Pulses (A and B)D Control Outputs1 RS-232 Communications2 RS-422 CommunicationsA Analog Output (4–20/0–20 mA)CE CE Approved VersionNOTE: RS-232/RS-422 and analog output options can not be combined.Newport 6-Digit Rate Meter/Totalizer6-digit ratemeter/totalizeroffers user programming viathe 5 front-panel keys. Scalefactor may be programmedfrom -99,999 to 999,999 (anydecimal point, multiply ordivide), while offset may beprogrammed from -99,999 to999,999 (any decimal point).Programs are stored in non-volatile memory, ▲ INFCTRAwith three levels of program lockout for security.Optional features include Hi or Lo setpoints for control or alarm, plusRS-232 communication. Fixed decimal point or autoranging is standard.Functions:Display:InputsType:Level:Frequency:Excitation:Accuracy:Setpoints:Alarm Outputs:Communication:Power:Dimensions/Weight:Panel Cutout:SPECIFICATIONSRate and totalize selected by menu6-digit, 7-segment red LED displaySingle input. TTL, CMOS, NPN open collector, contactclosure and magnetic pickup compatible; selected bydip switch. Non-isolatedMax. 60V; min. 25 mV rms30 kHz maximumRegulated, 5.0, 8.2, or 12.5V selected by DIPswitch, 100 mA max± 1 /2 LSD of total; 0.01% of the rate ± 1 /2 LSDTwo, optionalOptionalRS-232, analog output, optional230 ±15% VAC1.9" H x 3.8" W x 6" D(48 x 96 x 152 mm)/16 oz (454g)1.8" H x 3.6" W (45 x 92 mm)ORDERING INFORMATIONTo Order—Insert Number Code for Each Letter to Select Catalog Number. OrderExample: INFCTRA-0-1-1-0-RA – B – C – D – E – FDABCEFBasic UnitINFCTRAPower and Display0 115 VAC, Red LED1 230 VAC, Red LED2 115 VAC, Green LED3 230 VAC, Green LEDControl Output0 None1 Dual 6 AmpAnalog Output0 None1 Analog OutputSerial Output0 None1 RS-232ConfigurationR RatemeterT Totalizer

ATS Large Digital Displays• Run Time Accumulators• Production Monitors• GPS Clock Systems• Analog Input Displays• Counters• Timers▲AE46S–373▲AE2412▲STD–525▲AE44–503BRIGHT RUN TIME ACCUMULATORSAT/AE24-373 2.3 Inch, Four Digit, MM:SSAT/AE26-373 2.3 Inch, Six Digit, HH:MM:SSAT/AE44S-373 4 Inch, Six Digit, MM:SSAT/AE46S-373 4 Inch, Six Digit, HH:MM:SSOther sizes and configurations availableANALOG INPUT DISPLAYSAT/AE24-341 2.3 Inch, Four Digit, 4-20 mAAT/AE2412-341 2.3 & 1 Inch, Six Digit, 0-5VDCAT/AE26-341 2.3 Inch, Six Digit, 0-10VDCAT/AE24F-341 2.3 Inch, Four Digit, Flush MountAT/AE2412F-341 2.3 & 1 Inch, Six Digit, Flush Mt.AT/AE42S-341 4 Inch, Two Digit, 4-20mAAT/AE43S-341 4 Inch, Three Digit, 0-5VDCAT/AE44S-341 4 Inch, Four Digit, 0-10VDCAT/AE45S-341 4 Inch, Five Digit, 4-20mAAT/AE46S-341 4 Inch, Six Digit, 0-10VDCFour Digit ResolutionPRECISION TIMERSAT/STD-11-2 Measure & Display Accurate ElapsedTime: 0.000 – 9999.999 SecondsAT/STD-525T Measure Accurate Elapsed TimeMinutes, Seconds, Tenths andHundredths of secondsAT/2171-2 Handheld Pendant ControlPOWER OPTIONS12VAC12 VAC, 60HZ12V312 VDC to 15 VDC24VAC24 VAC, 60 Hz, 5VA220V1220 VAC, 60 Hz, 12.6 VAPC8Add 120 VAC Power Cord, 8’ longENCLOSURE OPTIONSOPT-N12A NEMA 12 rated, 16”W x 8”H x 6”DOPT-N12B NEMA 12 rated, 24”W x 8”H x 6”DOPT-N4XA NEMA 4X rated Stainless Steel,16”W x 8”H x 6”DOPT-N4XB NEMA 4X rated Stainless Steel24”W x 8”H x 6”DNEMA enclosures available on selected modelsLarge Bright Red LED Displays with digit sizes from 1” to12” high. Visible from 25 feet to 500 feet. Display temperature,pressure, flow and other process variables.Accumulate machine cycle time, run time or downtime.Monitor production counts. Synchronized clock systemswith GPS accuracy. Count-up or countdown elapsedtime. Custom units available.SYNCHRONIZED CLOCK SYSTEMSAT/MC4181LV Master Clock to synchronize Clocks, Bells,Time & Attendance System with ComputerAT/GPS-TR3 GPS Master Clock Interface, includesAntenna/Receiver and Interface.AT/CC2002 Four digit, four inch red LED ClockSingle sided, wall mount, 24 VACAT/CC2002W2 Four digit, four inch red LED ClockDouble sided, wall mount, 24 VACAT/CC2002C2 Four digit, four inch red LED ClockDouble sided, ceiling mt, 24 VACAT/CC2002 Four digit, four inch red LED ClockSingle sided, flush mount, 24 VACAT/8901–1821 24VAC, 200VA, (8 Amp) Power Supply.12” x 12” x 4”COUNTER OPTIONOPT-230 Event Counter (To 25Hz Speed)Input signals: 12-120V AC or DC, >20ms durationPRODUCTION MONITORSAT/AE44-503J Monitor GOAL and ACTUAL countsTwo lines of four digits, four inchAT/AE44-503C Designed for use with Remote Controller.AT/AE-503DX1 Controller for AE44-503C aboveDIGIT SIZEVIEWING DISTANCETypicalMaximum2.3" 70 ft 110 ft4" 120 ft 200 ft8" 240 ft 400 ft12" 360 ft 600 ftMISC.130