Semi-Finished - Engineering Plastic Products - Ensinger-online.com

Material standard values
Material
TECADUR
PBT GF30
TECAMID
6
TECAM
6 MO
TECAMID
6 GF25
black
TECAMID
6 GF30
black
TECAMID
6 ID
blue
TECAMID
66
TECAMID
66 MH
TECAMID
66 GF30
black
TECAMID
66/X GF50
black
Chemical Designation
PBT PA 6 PA 6 PA 6 PA 6 PA 6 PA 66 PA 66 PA 66 PA 66
Fillers
glass fibres
molybdenum
disulfide
glass fibres glass fibres detectable
filler
molybdenum
disulfide
glass fibres
glass fibres
Density
(DIN EN ISO 1183)
Mechanical properties
Modulus of elasticity (tensile test)
(DIN EN ISO 527-2)
Tensile strength
(DIN EN ISO 527-2)
Tensile strength at yield
(DIN EN ISO 527-2)
Elongation at yield
(DIN EN ISO 527-2)
Elongation at break
(DIN EN ISO 527-2)
Modulus of elasticity (flexural test)
(DIN EN ISO 178)
Flexural strength
(DIN EN ISO 178)
Compression modulus
(EN ISO 604)
Compressive strength (1% / 2 %)
(EN ISO 604)
Impact strength (Charpy)
(DIN EN ISO 179-1eU)
Notched impact strength (Charpy)
(DIN EN ISO 179-1eA)
Ball intendation hardness
(ISO 2039-1)
Thermal properties
Glass transition temperature
(DIN 53765)
Melting temperature
(DIN 53765)
Service temperature,
short term
Service temperature,
long term
Thermal expansion (CLTE),
23 – 60 °C (DIN EN ISO 11359-1;2)
Thermal expansion (CLTE),
23 – 100 °C (DIN EN ISO 11359-1;2)
Specific heat
(ISO 22007-4:2008)
Thermal conductivity
(ISO 22007-4:2008)
Electrical properties
Specific surface resistance
(DIN IEC 60093)
Surface resistance
(DIN IEC 60093)
Miscellaneous data
Water absorption 24 h / 96 h (23 °C)
(DIN EN ISO 62)
Resistance
to hot water / bases
Resistance to weathering
Flammability (UL94)
(DIN IEC 60695-11-10;)
[ g / cm³ ]
[ MPa ]
[ MPa ]
[ MPa ]
[%]
[%]
[ MPa ]
[ MPa ]
[ MPa ]
[ MPa ]
[ kJ / m² ]
[ kJ / m² ]
[ MPa ]
[ °C ]
[ °C ]
[ °C ]
[ °C ]
[ 10 -5 K -1 ]
[ 10 -5 K -1 ]
[ J / (g*K)]
[ W /(m*K)]
[ Ω ]
[ Ω*cm ]
[%]
1.46 1.14 1.14 1.33 1.36 1.24 1.15 1.15 1.34 1.61
3,400 3,300 3,300 5,100 5,700 3,600 3,500 3,200 5,500 8,700
46 79 84 96 98 80 85 84 91 115
46 78 82 96 98 80 84 83 91 115
5 4 5 9 4 4 7 10 8 2
6 130 37 11 5 21 70 40 14 2
3,400 2,900 3,100 4,900 5,200 3,100 3,100 4,700 9,000
78 100 110 143 140 110 114 135 200
2,800 2,700 2,900 3,900 4,200 2,700 2,700 4,100 6,200
20 / 38 24 / 41 17 / 32 21 / 42 21 / 42 20 / 35 20 / 38 25 / 46 28 / 56
37.0 n. b. n. b. 78.0 60.0 n. b. n. b. n. b. 97.0
7.0 5.0 4.0 5.0 5.0
190 155 160 230 232 175 168 216
45 51 49 49 45 47 52 48 78
224 221 220 217 218 220 258 253 254 256
200 160 160 180 180 160 170 170 170 200
110 100 100 100 100 100 100 100 110 130
8 12 8 7 6 11 10 5
10 13 8 8 6 12 10 5
1.2 1.6 1.6 1.4 1.3 1.5 1.5 1.2
0.33 0.37 0.37 0.40 0.41 0.36 0.36 0.39
10 14 10 14 10 14 10 14 10 14 10 13 10 14 10 14 10 14 10 14
10 14 10 14 10 14 10 14 10 14 10 14 10 14 10 14
0.02 / 0.04 0.3 / 0.6 0.3 / 0.6 0.2 / 0.3 0.2 / 0.3 0.3 / 0.6 0.2 / 0.4 0.2 / 0.4 0.1 / 0.2 0.1 / 0.2
- (+) (+) (+) (+) (+) (+) (+) (+) -
- - (+) (+) (+) - - (+) (+) (+)
HB e HB e HB e HB e HB e HB e HB e HB e HB e HB
Appendix
Data generated directly after machining (standard
climate Germany). For polyamides the values strongly
depend on the humidity content.
Test specimen to DIN EN ISO 527-2
+ good resistance
(+) limited resistance
– poor resistance (depending on concen -
tration, time and temperature)
n.b. not broken
n.a. not applicable
(a) Glass transition temperature
testing according to DIN EN ISO 11357
(b) Thermal conductivity testing according to ISO 8302
(c) Thermal conductivity testing according to ASTM E1530
(d) Surface resistance testing according to ASTM D 257
(e) No listing at UL (yellow card). The information might be
taken from resin, stock shape or estimation. Individual
testing regarding application conditions is mandatory.
(f) Thermal expansion (CLTE), 50 – 200 °C
98