2016_catalog_web

More documents

Recommendations

Info

Moeller hose and primer bulb assemblies are EPA- and CARB-approved and UV resistant. Bulbs feature dual internal check valves for rapid priming and fuel flowback prevention. The fuel line assembly connects your outboard to your Moeller fuel tank. The inner lining of older fuel hoses is susceptible to deterioration from E-10 fuel. Many outboards use primer bulbs, which are damaged by alcohol-blended fuels, too. If left unchecked, the liners may disintegrate and may cause clogging, poor running, and even engine failure. Newer fuel hoses include an inner liner to prevent deterioration from alcohol-blended fuels. When to Replace your Outboard Fuel Line Assembly Manufacturers generally use ten years as the lifespan for gasoline hoses, but it’s important to inspect the fuel lines every year. If there’s any doubt, replace them with EPA-compliant hose and new clamps. While your tank fitting is not part of the fuel asssembly, you will want to check it when you evaluate the rest of the fuel system. Hose should be inspected for cracks, stiffening, mushiness, and leaks around the fittings/connectors. Check your primer bulbs. If they feel squishy to the touch and the engine can “suck” the bulb flat, replace them. If the bulb is deteriorating, the check valves may fail and leave you stranded out on the water. Most fuel leaks occur at fittings, so careful installation of all components is critically important. Moeller uses O-ring construction on all fittings for tight, leak-free connections. For Moeller fuel line installation instructions, go to www.moellermarine.com. Be sure to have the manufacturer’s instructions handy before you begin. Remember to de-pressurize the fuel system before you begin work. ⚠ CAUTION: A1-15 is the ONLY fuel line you may use in an engine compartment. NEVER substitute B1-15 or any other line—only A1-15 is fire-rated. Fuel Line Components Hose The new EPA-mandated fuel lines (A1-15 and B1-15) use a tough inner liner which is compatible with ethanol blended fuels. The result is a less flexible hose, which makes it more difficult to install with other components. Take care when routing the lines; tight curves will generate kinks and flow stoppages, so make sure each bend radius is at least six inches. Clamps The clamps that keep the fuel lines tight are critical and warrant checking. They prevent fuel leaks and, just as important, prevent air leaks. Air leaks can ruin an engine in no time because the fuel/air mixture will become lean (too much air) and the engine will starve for fuel and burn up as a result. Use new quality all-stainless clamps if the old ones won’t hold, are corroded, or are falling apart. Hose clamps are cheap compared to a damaged engine. All Moeller clamps are 100% stainless steel. Anti-Siphon Valves (ASV) Anti-siphon valves reside in the outlet fitting from the tank to the engine (typically threaded right into the fitting) with a hose nipple on the fuel line end. The anti-siphon feature prevents fuel from flowing into the bilge if a failure occurs in the fuel line. Some cheaper valves can cause fuel restrictions to the engine; if you experience this, don’t be tempted to simply remove the anti-siphon valve. Instead, replace it with a quality Moeller anti-siphon valve. 35 |
UNIVERSAL Fuel Line Assemblies EPA 034390-10LPA 033389-10LPA 034395-10LPA 034387-10LPA International 034390-10 033389-10 034395-10 033387-10 3/8 in. ID Hose, B1-15, 6 ft. 3/8 in. ID Hose, B1-15, 12 ft. 5/16 in. ID Hose, B1-15, 6 ft. 3/8 in. ID Hose, A1-15, 12 ft. 3/8 in. ID Hose 3/8 in. ID Hose 5/16 in. ID Hose 3/8 in. ID Hose For package dimensions, go to www.moellermarine.com Gasoline & solvent-resistant Stainless steel clamps Dual internal check valves Tank Fitting NISSAN CHRYSLER SUZUKI Threads into fuel withdrawal on tank 033450-10 033491-10 033461-10 033503-10 033463-10 Tank Connector Attaches to fuel hose on the fuel tank side 033451-10 033492-10 033484-10 033487-10 033488-10 Engine Connector 033451-10 033492-10 033464-10 033467-10 033488-10 Attaches to fuel hose on the engine side PRIMER BULBS 034590-10LP 034690-10LP 034790-10LP International 034590-10 034690-10 034790-10 Primer Bulb with 3/8 in. Hose Barbs Primer Bulb with 5/16 in. Hose Barbs Primer Bulb with 1/4 in. Hose Barbs Primer Bulb with 3/8 in. Hose Barbs Primer Bulb with 5/16 in. Hose Barbs Primer Bulb with 1/4 in. Hose Barbs BULK FUEL FILL/VENT HOSE 034320 50 ft. roll of 1 1/2 in. ID Fuel Fill Hose 034330 100 ft. roll of 5/8 in. ID Vent Hose BULK FUEL HOSE 034375LP 034313LP 034376LP 034314LP 100 ft. rolls 3/8 in. ID Bulk Fuel Line (B1-15) 5/16 in. ID Bulk Fuel Line (B1-15) 1/4 in. ID Bulk Fuel Line (B1-15) 3/8 in. ID Bulk Fuel Line (A1-15) | 36
Page 1 and 2: Fueling the Fun! 2016 Edition www.m
Page 3 and 4: Table of Contents Introduction. . .
Page 5 and 6: ANATOMY OF A PORTABLE TANK PORTABLE
Page 7 and 8: Portable/Topside Tanks Internationa
Page 9 and 10: Portable /Topside Tanks Topside Tan
Page 11 and 12: Permanent Fuel Tanks Below Deck Tec
Page 13 and 14: Permanent Tanks All permanent tanks
Page 15 and 16: Permanent Tanks 032522 22 Gal/83L 2
Page 17 and 18: Permanent Tanks 032640 40 Gal/151L
Page 19 and 20: Permanent Tanks 032590 90 Gal/341L
Page 21 and 22: SAFETY MATTERS A few safety tips ab
Page 23 and 24: Fuel Transport International Jerry
Page 25 and 26: Transport Tanks 520028 Steel Wheel
Page 27 and 28: Installation & Replacement Parts OU
Page 29 and 30: Installation / Replacement Parts Al
Page 31 and 32: Installation / Replacement Parts 03
Page 33 and 34: Installation / Replacement Parts In
Page 35: Fuel Line Assemblies Photo courtesy
Page 39 and 40: Fuel Line Assemblies Bulb Hose Tank
Page 41 and 42: “You don’t hear a lot about pro
Page 43 and 44: Filters & Accessories For package d
Page 45 and 46: Motor Flushers & Extractors KEEP IT
Page 47 and 48: Motor Flushers/Extractors For packa
Page 49 and 50: Motor Flushers/Extractors 035801 Te
Page 51 and 52: Seating Moeller off-the-shelf seati
Page 53 and 54: Seating & Livewells Livewells 04228
Page 55 and 56: Waste Tanks & Water Tanks Back By P
Page 57 and 58: MOELLER WASTE TANKS Each tank featu
Page 59 and 60: For detailed information, please vi
Page 61 and 62: Paints Color Vision Paint Desc. Alp
Page 63 and 64: At Moeller, safety is our number on
Page 65 and 66: Battery Boxes and Components 042203
Page 67 and 68: Battery Boxes and Components Cover
Page 69 and 70: Miscellaneous Accessories Any compa
Page 71 and 72: Miscellaneous 020305-10 Brass Trans
Page 73 and 74: Plastic or Aluminum Which tank is r
Page 75: Marine Organizations and Regulatory

2016_catalog_web

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?