(1) OPPO客服中心施工图 Hyderabad, India OPPO customer service center construction plan(1)

More documents

Recommendations

Info

序号 /SN C-01 C-02 C-03 C-04 C-05 C-06 C-07 C-08 序号 /SN P-01 P-02 P-03 P-04 P-05 P-06 P-07 P-08 P-09 P-10 P-11 施工说明 1/Constructionspecifications 1 施工说明 2/Constructionspecifications 2 Location map of partrition wall size Drawing of ground material Position drawing of plug base 序号 /SN L-01 L-02 L-03 L-04 L-05 L-06 L-07 L-08 序号 /SN D-01 D-02 D-03 D-04 D-05 D-06 D-07 D-08 D-09 D-10 D-11 广东欧珀移动通讯有限公司本分 - 诚信 - 创新 - 团队品质 - 消费者导向 - 结果导向 Without our company's written permission, anycopy of it is forbidden.Never measure the drawing in this scale. Always keeping in the light of data in the drawing. Construction company should check the date in the drawing at building site. If find any mistake, please inform the engineer responsible for the drawing immediately. The copyright of the drawing is reserved by our company. 项目名称公司名称项目负责人 Item director 联系电话 Telephone 比例 Scale 设计师 Designer 目录 Catalog Item name OPPO- 客户服务中心施工图 Construction Drawing of Customer Service Center Serial number 编号 1-140902X-3XH 日期店形 Shop shape 联系电话 Telephone 审核人 Checker Date 2015.07.09 Company name 1:50A4 客户服务中心 Customer Service Center 陈浩 ChenHao 18249504913 施工监理 : 区域经理 Construction Supervision: Regional Manager The 2.0th generation shop design C-02
施工说明 (1) Constructionspecifications(1) ( 一 ) 设计依据 1.1 依据代理提供的相关图纸、现场状况。 1.2 依据《高层民用建筑设计防火规范》 GB50045-95-2005、《建筑内部装修设计防火规范》 GB50116-98、《中华人民共和国工程建设标准强制性条文》房屋建筑部分、《民用建筑工程室内环境污染控制规范》 GB50325-2001、《建筑装修防火设计材料手册》、《建筑装饰装修工程质量验收规范》 GB50210-2001、《建筑涂饰工程施工及验收规程》JGJ/29-2003、《建筑材料放射性核素限量》GB6566-2001。 1.3 消防部分依原有设计 . ( 二 ) 图纸说明 2.1 此施工图包含装修部分并符合相关规范规定。 2.2 本图所示与墙、柱等相对尺寸为控制尺寸 , 标高、位置、尺寸必须现场放线而定 , 而且须由设计人员认定后方可施工。 2.3 所有图例尺寸查核与现有差距 , 或与图例有区别时 , 施工者必须与技术人员联系 , 做尺寸修正或修正方案 , 以补充或变更设计图例为最新施工图。 2.4 标高均为装饰层面标高 , 天花标高为从本层地面起算的相对标高。 2.5 天花部分须完成设备施工和照明施工。 2.6 所有隐蔽工程木作部分均按国家有关规定刷防火 , 防腐漆。防火涂料应符合国家标准 , 并附有质量检测报告后方可封闭。 2.7 本工程选用材料必须由业主于设计师共同认可并符合国家有关建筑装修材料有害物质限量标准的规定。 2.8 本施工图中与空调、电器、给排水、消防有冲突之处 , 需协调各专业工程现场解决。 2.9 施工中设计师有权对所有图纸做局部调整 ( 有与代理协商同意的基础上 )。 2.10 本工程施工图尺寸以毫米 (mm) 为单位 , 标高以 (m) 米为单位。 2.11 本工程所用装饰材料必须符合环保要求 , 严禁使用国家明令淘汰的材料。 2.12 各装饰工序必须严格按国家《建筑装饰装修工程验收规范》执行。 ( 三 ) 材料说明 3.1 本工程采用的油漆、人选板材、涂料、油漆、胶粘剂、防水材料等必须符合环保要求方可使用。材料分类材料要求表面要求含水率备注五夹板柳桉面平整光滑 ≤8% 木方烘干白松无虫眼、树节 ≤8% 九夹板柳桉面平整光滑 ≤8% 用于基层时需做防火防尘处理十二夹板柳桉面平整光滑 ≤8% 18 厚木工板烘干杨木芯平整光滑 ≤8% 3.2 轻钢龙骨类 (1) 轻钢龙骨按照《88J 经》有关要求施工。 (2) 天花轻钢龙骨主吊筋间距不能大于 1000*1000mm, 主龙骨间距为 900mm, 次龙骨间距不能大于 400*1200mm。 (3) 吊挂件必须具有防锈能力。 (4) 隔断墙面采用轻钢龙骨外封 12 mm 厚水泥压力板外挂铁丝网抹 1:2 水泥砂浆后粘贴瓷砖和石材。 (5) 龙骨排布应考虑检修口、风口、灯具孔位置。吊筋用膨胀螺栓固定 , 不得挂钩 , 不得与管道固定 , 刷防锈漆 , 自攻螺丝帽要点防锈漆。镁质扳接缝要求留 3-5mm 收口缝 , 用专用嵌缝剂补平后粘贴纤维胶带 , 吊顶内所有木制品必须刷防火涂料。 (1)design basis 1.1 According to the relevant drawings and field status of the proxy. 1.2 According to China national standard number is: GB50045-95-2005, GB50116-98 , GB50210-2001,JGJ/29-2003,GB6566-2001.And the Compulsory Provisions of Engineering Construction Stanards of Buliding 1.3 The fire part according to the original design. (2)drawings description 2.1 This construction plan contains the decoration section and comply with the relevant regulations. 2.2 The relative dimensions of the wall, column, and other relative dimensions are controlled, and the elevation, position, and size must be placed in the field, and shall be determined by the design personnel. 2.3 All the legend size check and existing gap, or with the legend is different, the construction must and contact technical personnel, size adjustment or correction schemes, most new construction plans to add or change the design of legend. 2.4 Elevations are decorative level elevation, elevation from the relative elevation of the ceiling floor area. 2.5 Parts of the ceiling shall complete the construction and lighting of the equipment. 2.6 All wooden parts are hidden works according to the relevant provisions of brush fire prevention, anti-corrosion paint. Fire paint should comply with national standards, and with the quality of the inspection report can be closed. 2.7 The selection of materials for this project must be approved by the owner in common recognition of the designer and in accordance with the relevant provisions of the national standards for the harmful substances of the building materials for decoration materials. 2.8 In this construction plan and air conditioning, electrical appliances, water supply and drainage, fire conflict, the need to coordinate the professional field of the project to solve. 2.9The designer has the right to make a partial adjustment to all drawings (and on the basis of agreement with the agency).. 2.10 The engineering construction drawing size to millimeter (mm) as the unit, elevation to (m) m as the unit. 2.11 Decoration materials used in this project must meet the requirements of environmental protection, prohibited the use of obsolete materials. 2.12 Each decoration process must be strictly according to the national implementation. (3)Material Description 3.1 The paint used in this project, candidate for board, paint, paint, adhesive, waterproof material, etc. must comply with the requirements of environmental protection can be used. materials classification Five per cent splint material requirements The 2.0th generation shop design surface finish requirements rate of water content remarks Willow Eucalyptus surface flat and smooth ≤8% Use fire and dust flitch Dry white pine No bug, burl Nine per cent splint Twelve per cent splint 18mm carpenter board material requirements material requirements Drying core of cottonwood surface finish requirements surface finish requirements surface finish requirements 3.2Light gauge steel keel (1) Light steel keel in accordance with the relevant requirements of the by the construction. (2) Ceiling light steel keel main hanger spacing cannot be greater than 1000*1000mm, main keel spacing is 900mm, keel spacing cannot be greater than 400*1200mm. (3)Hanging pendant must have anti rust ability. (4) Cut off the wall with light steel keel outside seal 12 mm thick cement pressure plate plug 1:2 cement mortar paste ceramic tile and stone. (5)The keel should consider manhole, arrangement, air hole position lamps. Hanger with expansion bolts fixed, no hook, not with the fixed pipeline, brush paint, screw cap points antirust paint. Magnesia pull joint leave 3-5mm closing gap special caulking agent in reinforcing pasted fiber tape, the ceiling all wood products must brush fire retardant coating. ≤8% ≤8% ≤8% ≤8% prevention when used at basic level. 广东欧珀移动通讯有限公司本分 - 诚信 - 创新 - 团队品质 - 消费者导向 - 结果导向 Without our company's written permission, anycopy of it is forbidden.Never measure the drawing in this scale. Always keeping in the light of data in the drawing. Construction company should check the date in the drawing at building site. If find any mistake, please inform the engineer responsible for the drawing immediately. The copyright of the drawing is reserved by our company. 项目名称公司名称项目负责人 Item director 联系电话 Telephone 比例 Scale 设计师 Designer 施工说明 1 Construction specifications 1 C-03 Item name OPPO- 客户服务中心施工图 Construction Drawing of Customer Service Center Serial number 编号 1-140902X-3XH 日期店形 Shop shape 联系电话 Telephone 审核人 Checker Date 2015.07.09 Company name 客户服务中心 Customer Service Center 陈浩 ChenHao 施工监理 : 区域经理 1:50A4 18249504913 Construction Supervision: Regional Manager
Page 1: 广东欧珀移动通讯有
Page 5 and 6: 装饰材料表 (2.0 代 )/Deco
Page 7 and 8: 10870 5005 100 660 915 200 900 465
Page 9 and 10: F01 品牌 /Brand: 型号 ( 颜
Page 11 and 12: W01 10870 200 4905 200 2720 200 244
Page 13 and 14: 3 6W 1 set 100W 4 广东欧珀
Page 15 and 16: 不锈钢排椅 Stainless steel
Page 17 and 18: 广东欧珀移动通讯有

(1) OPPO客服中心施工图 Hyderabad, India OPPO customer service center construction plan(1)

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?