3 - Veneziani Yacht Paints

3 PAINTING YOUR BOAT
PAINT FINISHES FOR THE TOPSIDES, DECKHOUSE AND DECK
TIMBER GLOSS
Glossy wood varnish
CHARACTERISTICS
A one-pack modified alkyd
varnish, easy to apply, for
exterior and interior surfaces.
Varnish with excellent
gloss, good levelling properties,
brushability, flexibility
and resistance to marine
environment.
Recommended for all wooden
surfaces above waterline
and for over-coating old
varnishes.
TECHNICAL DATA
Specific weight:
0,92 +/- 0,02 Kg/L
Solids by volume: 45%
Colour: clear
Packaging: 0,75 L/2,50 L
32
APPLICATION DATA
Apply with: brush - roller -
conventional/airless spray
Drying time before use
(20°C): 12/24 hours
Thinner: 6470
DFT per coat: 40 µ
Theoretical coverage per
coat: 11,2 m 2 /L
Recoating time (20°C):
min 8 hours/max 7 days
Number of coats: 6-8
TOPSIDE, SUPERSTRUCTURES,
DECKHOUSE
WOOD VARNISHES
When you are treating wood on your
boat you can choose between two
different products: TIMBER GLOSS,
the traditional one-pack varnish or
marine flatting, or the two-pack
polyurethane varnishes WOOD
GLOSS (for exterior and interior surfaces)
or WOOD MAT (semi-gloss
varnish for interior surface)
WOOD GLOSS has better resistance
to external agents than the conventional
flatting varnishes, and so offers
longer durability.
If the wood is new it should first be
sanded and then impregnated with
1 coat of FIBRODUR. The finishing
coats should then be applied.
WOOD GLOSS
High-gloss wood finish
CHARACTERISTICS
A clear, two –pack glossy
varnish. Exceptionally resistant
against atmospheric
agents and the marine environment.
Excellent levelling
properties and high abrasion
resistance. Wood
Gloss enhances the beauty
of wood without shrinking
problems after application.
Particularly recommended
for clear finishes on exterior
and interior surfaces. Not
suitable for areas below the
waterline. Apply several
coats to obtain a perfect finish
with high durability in
aggressive environment.
TECHNICAL DATA
Specific weight:
1,02 +/- 0,02 Kg/L
Solids by volume: 38%
Colour: clear
Packaging: 0,75 L
At least 4-6 coats of TIMBER
GLOSS or WOOD GLOSS varnish
must be applied for the best results,
with a light sanding (360-400
grade sandpaper) between the
coats to obtain a glossy, smooth
surface.
On some, very prestigious boats, as
many as 12 coats are applied in order
to achieve the best finish and
durability.
For the first coats of varnish you
should thin the varnish by 30% to
start with and then gradually reduce
this amount until the final two coats
are applied without being thinned.
Always brush along the grain of the
wood and use the correct thinner.
If the wood is stained by water infiltration,
you must remove all the
paint from the affected area and
APPLICATION DATA
Apply with: brush - spray
Drying time before use
(20°C): 3 days
Pot life (20°C): 3 hours
Mixing ratio by volume: 4:1
Mixing ratio by weight:
80:20
Thinner: 5780
DFT per coat: 20 µ
Theoretical coverage per
coat: 19,0 m 2 /L
Recoating time (20°C):
min 8 hours/max 48 hours
Number of coats:
6 (up to 12)
The information given is a summary of the technical data sheets, for more details please contact the MTD.
WOOD MAT
Semi-glossy wood finish
CHARACTERISTICS
A clear, semi-glossy twopack
wood varnish with high
resistance against the marine
environment. Particularly
recommended for clear finishes
of bulkheads, furniture
and all internal wood surfaces.
Excellent levelling properties
and wear resistance.
Easy to apply. Not suitable
for areas below the waterline.
Well suited for wooden
decks and plancking.
TECHNICAL DATA
Specific weight:
1,00 +/- 0,02 Kg/L
Solids by volume: 50%
Colour: clear
Packaging: 0,75 L
treat the wood with 80 volumes of
oxygenated water or with TEAK 2
until the wood regains the original
colour.
Teak does not have to be varnished,
but simply cleaned, bleached and
protected with special products.
However, should you decide to varnish
it, we recommend you use a high-performance
system.
The durability of the system also
depends on regular maintenance.
If you are wise enough to finely
sand the surface every two
years and apply 2 new coats of
the product at the same time,
you will guarantee that your
wood will always be protected
and in perfect condition for
many years to come.
APPLICATION DATA
Apply with: brush - spray
Drying time before use
(20°C): 3 days
Pot life (20°C): 6 hours
Mixing ratio by volume: 1:1
Mixing ratio by weight:
50:50
Thinner: 5780
DFT per coat: 30 µ
Theoretical coverage per
coat: 16,7 m 2 /L
Recoating time (20°C):
min 8 hours/max 48 hours
Number of coats: 3-4