Timken - Ball Bearing Housed Units

RCJT, TCJT, LCJT
Industrial Series
Industrial
BALL BEARING HOUSED
Series
UNITS
BALL BEARING HOUSED UNITS • CAST-IRON FLANGED UNITS • RCJT, TCJT, LCJT
RCJT, TCJT, LCJT INDUSTRIAL SERIES
• The cartridges are the same basic design as RCJ, TCJ, and
LCJ types, except they have two bolt holes instead of four.
• This series is primarily designed for applications where the
mounting area is restricted.
• The RCJT cartridge is equipped with G-KRRB (R-seal) H wideinner-ring
ball bearings. The TCJT is equipped with G-KPPB
(tri-ply seal) wide-inner-ring ball bearings. The LCJT is
equipped with the G-KLLB (Mechani-seal) wide-inner-ring
ball bearings.
• The units are factory-prelubricated, but a grease fitting is
provided for relubrication.
• Safety end caps are available for selected sizes.
Suggested shaft tolerances:
1⁄2 in. – 1 15 ⁄16 in., nominal to -0.013 mm, -0.0005 in.;
2 in. – 2 3 ⁄16 in., nominal to -0.025 mm, -0.0010 in.
To order, specify UNIT and SHAFT DIAMETER.
Example: RCJT 1 3 ⁄16 in., TCJT 1 3 ⁄16 in.
H
L
N
BOLT HOLE
J
L
N
BOLT HOLE
J
d 1
BEARING DATA
d 1
A
E
Unit Bearing No. Dimensions and Load Ratings
RCJT G-KRRB Page A-34
TCJT G-KPPB Page A-39
LCJT G-KLLB Page A-37
A 1
A
E
A 1
Unit
Shaft
Bolt
Dia. H J L A N E A 1 d 1 Size
in.
mm
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
Bearing
No.
RCJT TCJT LCJT
Collar
No.
Housing
No.
RCJT 1⁄2
G1008KRRB
S1008K
RCJT 5⁄8 98.4 76.2 54.0 23.6 10.7 40.6 10.3 28.1 10 G1010KRRB S1010K
3 7 ⁄8 3 2 1 – –
RCJT 11⁄16 ⁄8 0.929 27⁄64 1.599 13⁄32 1.105 3⁄8 G1011KRRB S1011K
T-40219
RCJT 17 GE17KRRB SE17K
RCJT 3⁄4 111.9 89.7 60.5 27.8 10.7 46.4 11.1 32.8 10 G1012KRRB
S1012K
4 13 ⁄32 3 17 ⁄32 2 3 – –
RCJT 20 ⁄8 1.094 27⁄64 1.828 7⁄16 1.292 3⁄8 GE20KRRB SE20K
T-40220
RCJT, TCJT, LCJT 13 ⁄16
G1013KRRB G1013KPPB3 G1013KLLB S1013K
RCJT, TCJT, LCJT 7⁄8 G1014KRRB G1014KPPB3 G1014KLLB S1014K
123.8 99.2 69.8 27.9 11.5 46.7 11.1 23.9 10
RCJT, TCJT, LCJT 15 ⁄16
4 7 ⁄8 3 29 ⁄32 2 3 G1015KRRB G1015KPPB3 G1015KLLB S1015K
⁄4 1.100 29⁄64 1.839 7⁄16 1.480 3⁄8
RCJT, TCJT, LCJT 1 G1100KRRB G1100KPPB3 G1100KLLB S1100K
RCJT, TCJT, LCJT 25 GE25KRRB GE25KPPB3 GE25KLLB SE25K
RCJT, TCJT, LCJT 1 1 ⁄16
G1101KRRB G1101KPPB3 G1101KLLB S1101K
RCJT, TCJT, LCJT 1 1 ⁄ 8 G1102KRRB G1102KPPB3 G1102KLLB S1102K
141.3 116.7 79.4 29.9 11.5 50.5 11.9 43.7 10
RCJT, TCJT, LCJT 1 3 ⁄16
5 9 ⁄16 4 19 ⁄32 3 1 G1103KRRB G1103KPPB3 G1103KLLB S1103K
⁄8 1.178 29⁄64 1.990 15⁄32 1.730 3⁄8
RCJT, TCJT, LCJT 1 1 ⁄4 S G1103KRRB3 G1103KPPB4 G1103KLLB3 S1103K3
RCJT, TCJT, LCJT 30 GE30KRRB GE30KPPB3 GE30KLLB SE30K
RCJT, TCJT, LCJT 1 1 ⁄4
G1104KRRB G1104KPPB2 G1104KLLB S1104K (1)
RCJT, TCJT, LCJT 1 5 ⁄16 G1105KRRB G1105KPPB2 G1105KLLB S1105K (1)
155.6 130.2 92.1 31.8 13.1 53.5 11.9 53.6 12
T-40223
RCJT, TCJT, LCJT 1 3 ⁄8
6 1 ⁄8 5 1 ⁄8 3 5 G1106KRRB G1106KPPB2 G1106KLLB S1106K
⁄8 1.254 33⁄64 2.106 15⁄32 2.112
1⁄2
(T-21414)
RCJT, TCJT, LCJT 1 7 ⁄16 G1107KRRB G1107KPPB2 G1107KLLB S1107K (1)
RCJT, TCJT, LCJT 35 GE35KRRB GE35KPPB2 GE35KLLB SE35K
RCJT, TCJT, LCJT 1 1 ⁄2
G1108KRRB G1108KPPB3 G1108KLLB S1108KT
171.4 143.6 104.7 38.1 13.1 59.3 12.7 58.2 12
T-40224
RCJT, TCJT, LCJT 1 9 ⁄16
6 3 ⁄4 5 21 ⁄32 4 1 G1109KRRB G1109KPPB3 G1109KLLB S1109KT
⁄8 1.500 33⁄64 2.334 1⁄2 2.292 1⁄2
(T-22529)
RCJT, TCJT, LCJT 40 GE40KRRB GE40KPPB3 GE40KLLB SE40K
RCJT, TCJT, LCJT 1 5 ⁄8
G1110KRRB G1110KPPB4 G1110KLLB S1110K
RCJT, TCJT, LCJT 1 11 ⁄16 179.4 148.0 111.1 38.9 13.1 59.3 12.7 63.0 12 G1111KRRB G1111KPPB4 G1111KLLB S1111K T-40225
RCJT, TCJT, LCJT 1 3 ⁄4 7 1 ⁄16 5 27 ⁄32 4 3 ⁄8 1.531 33⁄64 2.334 1⁄2 2.480 1⁄2 G1112KRRB G1112KPPB4 G1112KLLB S1112K (T-21416)
RCJT, TCJT, LCJT 45 GE45KRRB GE45KPPB4 GE45KLLB SE45K
RCJT, TCJT, LCJT 1 7 ⁄8
G1114KRRB G1114KPPB3 G1114KLLB S1114K
188.9 157.2 115.9 42.9 17.1 66.4 12.7 69.3 16
T-40226
RCJT, TCJT, LCJT 1 15 ⁄16
7 7 ⁄16 6 3 ⁄16 4 9 G1115KRRB G1115KPPB3 G1115KLLB S1115K
⁄16 1.688 43⁄64 2.615 1⁄2 2.730 5⁄8
(T-21418)
RCJT, TCJT, LCJT 50 GE50KRRB GE50KPPB3 GE50KLLB SE50K
RCJT, TCJT, LCJT 2
G1200KRRB G1200KPPB4 G1200KLLB S1200K
RCJT, TCJT, LCJT 2 1 ⁄8 215.9 184.1 127.0 46.8 17.1 75.1 16.7 75.7 16 G1202KRRB G1202KPPB4 G1202KLLB S1202K T-40227
RCJT, TCJT, LCJT 2 3 ⁄16 8 1 ⁄2 7 1 ⁄4 5 1.844 43⁄64 2.958 21⁄32 2.980 5⁄8 G1203KRRB G1203KPPB4 G1203KLLB S1203K (T-23788)
RCJT, TCJT, LCJT 55 GE55KRRB GE55KPPB4 GE55KLLB SE55K
(1)
Add C1 suffix to collar numbers for G-KPPB2 bearings (TCJT).
NOTE: Shaft diameter with an S = smaller housing.
New
(Old)
Unit
Wt.
kg
lbs.
0.590
1.30
0.590
1.30
T-40221 0.785
(T-21412P) 1.73
T-40222 1.090
(T-21548P) 2.40
1.444
3.18
2.193
4.83
2.379
5.24
2.724
6.00
3.668
8.08
TIMKEN ® HOUSED UNIT CATALOG • Download 3D Models and 2D Drawings at cad.timken.com A-103