CMIT 320 ADMINISTERING WINDOWS SERVER QUIZ 13.3 ANSWERS
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>CMIT</strong> <strong>320</strong> <strong>ADMINISTERING</strong> <strong>WINDOWS</strong> <strong>SERVER</strong> <strong>QUIZ</strong> <strong>13.3</strong><br />
<strong>ANSWERS</strong><br />
BUY HERE⬊<br />
htp://www.seetutorials.com/cmit-<strong>320</strong>-<br />
administering-windows-server-quiz-13-3-<br />
answers/<br />
<strong>CMIT</strong> <strong>320</strong> Quiz <strong>13.3</strong> Answers<br />
1. RouterA and RouterB are connected with a serial link. RouterA is the DTE device. A portion of the show interface<br />
command output for RouterB is shown below:<br />
RouterB#show interface s0/0/0<br />
Serial0/0/0 is down, line protocol is down Hardware is GT96K Serial<br />
Internet address is 192.168.105.97/30<br />
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation PPP,<br />
loopback not set<br />
Keepalive set (10 sec)<br />
You need to configure RouterA to connect to RouterB. Which commands would you use to configure the Serial 0/1/1<br />
interface for RouterA?<br />
2. Which of the following are true when configuring a serial connection between two routers?(Select two.)<br />
3. Your client has acquired several small companies and would like to connect them together into one network. Not<br />
all the routers are Cisco devices and compatibility is a concern. Which WAN encapsulation method should you<br />
recommend your client use?<br />
4. RouterA is connected to RouterB through Serial1. You want to configure the link to use PPP with CHAP<br />
authentication with a password of cisco. Which set of commands would you use on RouterA to complete the<br />
configuration?<br />
5. Two routers with the hostnames SLC and PROVO have been configured to connect using PPP with CHAP<br />
authentication through their BRI0 interfaces. Attempts to establish a session between the two routers fails. You check<br />
the running configuration on both routers and find the output shown below:<br />
6. You're documenting the configuration of your router. When you run the show interfaces S0 command, you receive<br />
the output shown below:<br />
Router_1#show interface S0<br />
Serial0 is up, line protocol is up<br />
Hardware address is HD64570<br />
MTU 1500 bytes, BW 10000 Mbit, DLY 2000 usec, rely 255/255, load 1/255<br />
Encapsulation PPP, loopback not set Keepalive set (10 sec)<br />
LCP Open<br />
Open: IPCP, CDPCP<br />
7. Which of the following statements about the functionality of LCP are true? (Select three.)<br />
8. Which of the following are benefits of LCP? (Select three.)
9. What is the connection order used by two TCP/IP routers to open a session with PPP including authentication?<br />
10. PPP supports authentication, compression, and multiple Networklayer protocols. Which of the following correctly<br />
sequences these functions as performed when a PPP link is established?<br />
11. Which of the following protocols is used by PPP to enable support for multiple Networklayer protocols?<br />
12. You have two routers connected as shown in the diagram. The serial interfaces on both routers have been<br />
configured with an IP address, and the shutdown has been removed. Your task in this lab is to configure both routers<br />
to use PPP.<br />
Complete the following tasks:<br />
13. When is Multilink PPP used?<br />
14. Which of the following commands demonstrates the first step in configuring a new multilink interface?