MC5716 Technical Specification ZTE CORPORATION - wless.ru

More documents

Recommendations

Info

5.16 +CNMI 5.16.1 Syntax Command Possible response(s) +CNMI=[[,[,< bm>[,[, ]]]]] OK Upon an error relating to SMS: +CMS ERROR: III MC5716 Technical Specification +CNMI? +CNMI: ,,,,OK +CNMI=? +CNMI: (list of supported s),(list of supported s),(list of supported s),(list of supported s),(list of supported s) OK 5.16.2 Interface 5.16.3 Value Set command is used to set new message to TE. and are used to set new message alert (including +CMTI, ^HCMT, +CDSI and ^HCDS) is used to set directly report to TE or save in MT and report the storage location when receiving a message. do not use temporarily is used to set whether or not report message status report(+CDSI, ^HCDS). Test command is used to return the supported parameter value. Note: The settings will be cleared after MT is restarted, at this moment, it would not report any new message. It’s recommended not to use AT+CNMI=0,0,0,0,0. is used to set message alert method (currently supports mode=1) 0 cache the message alert in ME. If ME is full, cover the old message alerts. 1 Directly send the message alert to TE. As it’s unable to send (in online data mode), abandon the alert. 2 Directly send the message alert and message status report to TE. As it’s unable to send (e.g., in online mode), cache the message in ME; and send it to TE when possible. Note: the message alerts are cached in volatile memory. If the power is off before MT sends it, the messages might be missing. Therefore, as =0 or2, can’t directly forward the message(=2 and 3) set the storage and alert specification of receiving messages. For the storage and alert of new messages, there are the following three methods: 1. Save SMS-DELIVER into MT and send TE a notification of storage location. +CMTI: , 2. Do not save SMS-DELIVER in MT and directly send SMS-DELIVERS to TE. Text mode: ^HCMT: ,,,,,,,,,, , ,, 3. Save SMS-DELIVER in MT and do not send SMS-DELIVER to TE.
Specification The interaction of TE and MT are as follows: TE MS NETWO Directly report New msgs Acknowledge(+CNMA) Directly report Not acknowledged in certain time Save msgs in MS and report storage location Save msgs in MS, do not report RP-ACK New msgs Network timeout New msgs RP-ACK New msgs RP-ACK MC5716 Technical Directly report msgs to TE. If not acknowledged within certain time, send RP-ERROR to network Save msges in MS and send RP-ACK and report storage location. Save msgs in MS and send RP_ACK to the network, do not report the parameter values and storage and alert of messages are related in the table below: no class or class 1 class 0 or message waiting indication group (discard) class 2 or message waiting indication group (store) class 3 0 1 +CMTI [+CMTI] +CMTI +CMTI 2 ^HCMT & ^HCMT [& +CMTI ^HCMT & +CNMA +CNMA] +CNMA 3 +CMTI [+CMTI] +CMTI ^HCMT & +CNMA III
Page 2 and 3: MC5716 Technical Specification ZTE
Page 4 and 5: MC5716 Technical Specification Tabl
Page 6 and 7: 1 PRODUCT INTRODUCTION III MC5716 T
Page 8 and 9: 3 APPEARANCE AND STRUCTURE Appearan
Page 10 and 11: MC5716 Technical Specification In C
Page 12 and 13: 1 UIM card status valid 240 ROMSIM
Page 14 and 15: 5.8 ^RESET 5.8.1 Syntax Command Pos
Page 16 and 17: 1 Voice call 2 data 4 fax 8 sms 5.1
Page 18 and 19: 5.13.2 Interface Execution command
Page 22 and 23: Specification Descriptions: ^HCMT &
Page 24 and 25: 5.20 +CNMA 5.20.1 Syntax 0(or defau
Page 26 and 27: 5.23.1 Syntax MC5716 Technical Spec
Page 28 and 29: 0 UNKNOWN 1 TELEPHONY Message mark
Page 30 and 31: 7—other encoding method Type of
Page 32 and 33: MC5716 Technical Specification mes
Page 34 and 35: 6 FUNCTIONS 6.1 Voice functions MC5
Page 36 and 37: 7 TECHNICAL SPECIFICATION MC5716 Te
Page 38 and 39: 7.3 RF Transmitting Table 12 RF Tra
Page 40: 8 STANDARDS REFERENCE 37 MC5716 Tec

MC5716 Technical Specification ZTE CORPORATION - wless.ru

Create successful ePaper yourself

Delete template?

Save as template?