SC Pro Technical Data Sheet

More documents

Recommendations

Info

Installation information Installation data - threaded rod T max SC-PRO - Threaded rod Notation Unit M8 M10 M12 M16 M20 M24 S w Anchor diameter d [mm] 8 10 12 16 20 24 t fix d f Nominal drill bit diameter d 0 [mm] 10 12 14 18 22 26 Diameter of hole clearance in fixture d f [mm] 9 12 14 18 22 26 Diameter of steel brush d b [mm] 11 13 16 20 24 28 h min h 1 h ef Effective embedment & drill hole depth h ef [mm] 80 90 110 125 170 210 Minimum member thickness for h ef h min [mm] 110 120 140 160 220 260 Minimum spacing for h ef s min [mm] 40 45 55 65 85 105 Minimum edge distance for h ef c min [mm] 40 45 55 65 85 105 d 0 Thickness of fixture t fix [mm] 0 mm ≤ t fix ≤ 500mm Maximum torque T max [Nm] 10 20 40 80 120 150 Torque wrench socket size S w [mm] 13 17 19 24 30 36 Installation Instructions Hammer Drilled Hole 1 Using the proper drill bit size, drill a hole into the base material to the required depth. 2 Blow the hole clean using a hand pump or compressed air 2 - 2 times minimum. 3 Brush the hole with the proper wire brush - 2 times minimum. 4 Blow the hole clean using a hand pump or compressed air 2 - 2 times minimum 3 . 5 Shake capsule to distribute adhesive components. 6 Insert the capsule into the hole. 7 Insert driver/drive unit in rotary hammer drill. Insert threaded rod to the driver/drive unit. In hammer mode at 250-500RPM, break glass and spin rod into the hole until fully embedded. Turn the rotary hammer drill off immediately. 8 Allow the adhesive to cure for the time specified for the actual concrete temperature. Do not disturb or load the anchor until the adhesive has fully cured. Follow longer curing time for wet concrete. 1 2 3 4 5 6 7 8 e.g. 20˚C 2X 2X 2X 20 min Notes: 1. Always refer to the product assessment reports and approvals (e.g. ETA) for detailed information including the design criteria 2. Always use appropriate filters to prevent oil from the compressed air unit contaminating the drilled hole. The compressed air shall be free from oil. 3. Holes may be dry or damp, but should be free of standing water or frost. 8 SC-PRO Technical Data Sheet. Last modified September, 2017
Threaded Rod POWERS supplies a range of adhesive anchor studs for use based on standard embedment depth applications. For alternate embedment depths, studs should be cut to specified size as per application requirements. Studs are available in stainless steel, galvanised steel and zinc plated carbon steel complete with nut and washer. Environmental factors and application factors should be considered carefully prior to selecting the correct stud. Chisel Point Stud • Suitable for use with Powers SC-PRO capsules or any adhesive injection system. • Depth set mark for accurate embedment depth. • External hex for stability when driving the stud in glass Size Drill Dia Embed Depth Fixture Thickness Box Qty ZINC GAL STAINLESS Carton Qty Part No. Part No. Part No. 8 x 110mm 10 80 15 10 200 STM8110-PWR STM8110G-PWR STM8110SS-PWR 10 x 130mm 12 90 21 10 200 STM10130-PWR STM10130G-PWR STM10130SS-PWR 12 x 160mm 14 110 27 10 100 STM12160-PWR STM12160G-PWR STM12160SS-PWR 16 x 190mm 18 125 40 10 50 STM16190-PWR STM16190G-PWR STM16190SS-PWR 20 x 260mm 24 170 60 5 25 STM20260-PWR STM20260G-PWR STM20260SS-PWR 24 x 300mm 28 210 56 5 20 STM24300-PWR STM24300G-PWR STM24300SS-PWR Accessories Hole Cleaning Blow Pump For dust extraction (up to 20mm hole sizes) SDS Plus Wire Brush For machine cleaning Description Drilled Hole Ø Brush Size Thread Width Box Qty Carton Qty Part No. Standard Steel Brush 18 20 M6 1 N/A AWBM16-PWR Standard Steel Brush 20 22 M6 1 N/A AWBR16-PWR Standard Steel Brush 24 26 M6 1 N/A AWBM20M24-PWR Standard Steel Brush 32 34 M6 1 N/A AWBM30-PWR Standard Steel Brush 37 40 M6 1 N/A AWBM36-PWR Standard Steel Brush - SDS Plus Extension 300mm M6 1 N/A AWBEXT-PWR Standard Steel Brush - SDS Plus Adaptor M6 1 N/A AWBSDSPLUS-PWR Blow Pump - Industrial 1 N/A BLOWPUMP-PWR SC-PRO Technical Data Sheet. Last Modified September, 2017 9
Page 1 and 2: VINYLESTER GLASS SPINNING CAPSULE A
Page 3 and 4: SC-PRO Vinylester Glass Spinning Ca
Page 5 and 6: Working Stress Design UNCRACKED CON
Page 7: Resistance to Chemicals Chemical Ag

SC Pro Technical Data Sheet

Create successful ePaper yourself

Delete template?

Save as template?