Adabas Response Codes - Software AG Documentation

More documents

Recommendations

Info

Adabas Response Codes Response 102 Origin Mainframe systems only Explanation Space calculation error. Action Retry the open operation. Response 106 Origin Mainframe systems only Explanation The prefetch table record buffer specified in the UDB is too small. Response 107 Origin Mainframe systems only Explanation Either a GETMAIN error occurred or there was insufficient space when performing prefetch. Prefetch is switched off. Response 109 Origin Mainframe systems only Explanation The specified command ID is already active on another database for this user. Response 110 Origin Mainframe systems only Explanation The command ID pool is full. Action Increase the size of either or both the ADARUN NQCID or NU parameters. Response 113 52 Origin Mainframe and open systems Table of Contents
Table of Contents Explanation The specified ISN was invalid for one of the following reasons: An HI command was issued with ISN less than MINISN or with an ISN equal to zero (0). An N2 command was issued with ISN equal to 0 or larger than the MAXISN in effect for the file. An N2 command was issued and the specified ISN was assigned to another record in the file. An A1, L1/L4, E1, or S1/S2/S4 (with FB) command was issued for a nonexistent ISN. An L3/L6 command found an ISN in the index which did not exist in the address converter. An N1/N2 command tried to access a file protected by security-by-value, but the command user is not authorized to access the file. A read or update command tried to access a multiclient file’s record using either a blank or incorrect-length owner ID, or an owner ID that does not apply to the record. An RI command was issued for a record that has been updated earlier in the same transaction. The record cannot be released from hold status prior to transaction end. On mainframe systems, subcode 5 is issued for this reason. Subcode 19 is given when a base file record is not found in the address converter (AC). At the end of a LOB update in the LOBfile, the associated base file record no longer existed. Subcode 249 is given only when Adabas Vista is in use. Refer to the Adabas Vista documentation for more information. Open Systems On open systems, the following subcodes may occur: Subcode Meaning 249 (0x00F9) An invalid ISN was detected by Adabas Vista (open systems). The ISN specified for an E1, HI or L1 command is not consistent with the definitions for the partitioned file. Action: Review the program logic Action Correct the ISN problem and try again. Adabas Response Codes 53
Page 1 and 2: Adabas Response Codes Adabas Respon
Page 3 and 4: Table of Contents Explanation The m
Page 5 and 6: Overview of Messages Response 3 Ori
Page 7 and 8: Overview of Messages Response 10 Or
Page 11 and 12: Overview of Messages Explanation Th
Page 13 and 14: Table of Contents Response 25 Origi
Page 23 and 24: Overview of Messages Action The fol
Page 29 and 30: Table of Contents Action Increase t
Page 43 and 44: Table of Contents Action The method
Page 49 and 50: Overview of Messages Action For mai
Page 51: Table of Contents Explanation An er
Page 55 and 56: Overview of Messages Response 123 O
Page 57 and 58: Overview of Messages Response 131 R
Page 59 and 60: Table of Contents Explanation The e
Page 61 and 62: Table of Contents Response 143 Orig
Page 63 and 64: Table of Contents Origin Mainframe
Page 65 and 66: Overview of Messages Explanation Th
Page 75 and 76: Overview of Messages Explanation Ei
Page 93 and 94: Overview of Messages Response 248 R
Page 95 and 96: Table of Contents Explanation Mainf
Page 97 and 98: Overview of Messages Explanation On
Page 99 and 100: Overview of Messages Explanation On
Page 101 and 102: Overview of Messages Explanation A

Adabas Response Codes - Software AG Documentation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?