CP6070-2S7MP

More documents

Recommendations

Info

GT CP3788 - 4 Piston CP3799 - 4 Piston GENERAL INFORMATION APPLICATIONS - General GT. FEATURES - Two piece cast aluminium alloy body with hard anodised surface treatment. - Radial mount. - To suit Ø356.0/330.0/315.0/ 295.0mm x 32.0/28.0mm disc. - Differential bores, to control pad taper. - Aluminium pistons with high temperature seals. - Stainless steel bridge pipe, pad abutments & wear plates. - H/Piece pad retainer. - Rear Caliper available. CP3789 Series. PART NUMBERS - To suit disc Ø356 x 32mm CP3788-16S7 RHT /-17S7 LHT / -18S7 RHL /-19S7 LHL. - To suit disc Ø330 x 32mm CP3788-2S7 RHT /-3S7 LHT /-4S7 RHL /-5S7 LHL. - To suit disc Ø315/295 x 28mm. CP3788-6S4 RHT /-7S4 LHT / -8S4 RHL /-9S4 LHL CALIPER HANDING It is important to select the correct ‘hand’ of caliper. See note on page 4 for guidance. PAD INFORMATION - Pad Family = CP2279D50 - Pad Area = 57.4cm² - Pad Depth = 50.3mm - Pad Thickness = 20.5mm INSTALLATION DRAWING EFFECTIVE RADIUS W4 MAX WHEEL / DISC C L DISC WIDTH W1 MAX W2 MAX W3 MAX R8.0 RADIUS R4 MIN RADIUS R3 MIN RADIUS R2 MAX RADIUS R1 MAX 45.67 INLET PORT M10X1.0 TECHNICAL SPECIFICATION Piston Sizes Ø38.1mm Ø44.5mm Disc Diameter Max Ø356.0mm Min Ø295.0mm Disc Thickness Max 32.0mm Min 28.0mm Weight No Pads 2.3Kg Hydraulic Thread M10x1.0 Mounting Type Radial Mtg centres 152.0mm Mtg offset -2 to 5 & -16 to -19S7 44.1mm -6/-7/-8/-9S4 42.1mm Mtg hole Ø 12.15mm ‘PL’ Dimension 57.5mm Seal Repair Kit CP4518-JL Bleed Screw 17Nm Tightening Torque (12.5lbs/ft) SPARE PARTS Pistons Ø38.1mm CP3636-107 Ø44.5mm CP3394-110 Pad Retainer H/Piece Retainer P/No. -2/-3/-4/-5S7 CP3799-109 -6/-7/-8/-9S4 CP3788-112 -16/-17/-18/-19S7 CP3795-101 Ret / Bolt No. -2 to 5S7 & CP3439-111 -16 to -19S7 -6/-7/-8/-9S4 CP3344-112 Wear Plates CP3799-110 x 1 / CP3799-111 x 1 CP3846-101 x 2 Bleed Screw CP3720-173 Fluid Pipe -2 to 5S7 & CP3799-6 -16 to -19S7 -6/-7/-8/-9S4 CP3788-10 131.3 (5.17”) 130.00 MAX 123.00 DISC OUTSIDE DIAMETER DISC ROTATION MYG HOLE CTRS 152.00 TOP OF DISC & PAD MATERIAL 28.27 57.5 DIMN ‘PL’ DISC PATHWAY RADIUS ‘N’ 54.1 (2.02”) DIMN ‘U’ 12.15 MTG HOLES Ø22.00 C/BORE OFFSET CHOICE OF BOLTED ‘H’ PIECE OR QUICK RELEASE CLIP Disc Ø W1 W2 W3 R1 R2 R3 R4 EFF RAD 330 x 32 80.0 78.6 53.0 183.0 170.5 113.5 110.5 141.4 315 x 28 78.0 76.6 51.0 175.5 163.0 106.5 103.0 134.3 295 x 28 78.0 76.6 51.0 168.5 153.0 96.5 93.0 134.2 GENERAL INFORMATION APPLICATIONS - GT3 Rear. FEATURES - Two piece cast aluminium alloy body with hard anodised surface treatment. - Radial mount. - To suit Ø355.0 or 330.0mm x 32.0 / 28.0mm disc. - Differential bores, to control pad taper. - Aluminium pistons with high temperature seals. - Stainless steel bridge pipe, pad abutments & wear plates. - H/Piece pad retainer. PART NUMBERS - To suit disc Ø330.0 x 32.0mm CP3799-2S0 RHT /-3S0 LHT / -4S0 RHL /-5S0 LHL. CALIPER HANDING It is important to select the correct ‘hand’ of caliper. See note on page 4 for guidance. PAD INFORMATION - Pad Family = CP2279D50 - Pad Area = 57.4cm² - Pad Depth = 50.3mm - Pad Thickness = 20.5mm Brake Calipers INSTALLATION DRAWING R1 MAX TECHNICAL SPECIFICATION Piston Sizes Ø28.6mm Ø34.9mm Disc Diameter Max Ø355.0mm Min Ø330.0mm Disc Thickness Max 32.0mm Min 28.0mm Weight No Pads 2.53Kg Hydraulic Thread M10x1.0 Mounting Type Radial Mtg centres 152.0mm Mtg offset 44.10mm Mtg hole Ø 12.15mm ‘PL’ Dimension 57.74mm Seal Repair Kit CP4518-DG Bleed Screw Tightening Torque 17Nm (12.5lbs/ft) SPARE PARTS Pistons Ø28.6mm CP3799-112 Ø34.9mm CP3789-106 Pad Retainer H/Piece Retainer P/No. CP3799-106 Ret / Bolt No. CP3394-112 Wear Plates CP3799-110 x 1 / CP3799-111 x 1 CP3846-101 x 2 Bleed Screw CP3720-173 Fluid Pipe CP3799-6 131.3 (5.17”) 131.0 MAX 123.0 Ø28.6 (1.12”) LEADING DIRECTION OF DISC ROTATION DISC DIAMETER www.apracing.com +44 (0)24 7663 9595 R2 MAX R5 MIN ‘E’ DIMN DISC WIDTH 77.00 MAX 86.00 MAX 79.00 MAX W1 MAX W2 MAX 53.0 MAX 53.0 MAX R8.00 R6 MIN R4 MIN R3 MAX 45.67 BLEEDSCREW MAX TIGHTENING TORQUE 17Nm AT AMBIENT. INLET PORT M10x1.0 THREAD Ø22.00 C/BORE ‘D’ DIMN 152.00 Ø34.9 (1.37”) TRAILING 54.1 (2.02”) DISC PATHWAY RADIUS R180.00 EFFECTIVE RADIUS PAD RETAINER BOLT MAX TORQUE 15Nm (11LbFt) ‘PL’ DIMN 57.74 Ø12.15 MTG HOLE DIMN ‘C’ OFFSET 44.10 Disc Ø W1 W2 R1 R2 R3 R4 R5 R6 EFF RAD ‘U’ Dim’n 356 x 32 41.0 46.0 196.0 182.0 164.0 146.0 125.5 122.5 153.6 119.76 330 x 28 37.0 40.0 187.0 170.0 152.0 134.0 113.5 110.5 141.5 107.26 ‘U’ DIMENSION 17
18 Brake Calipers GT CP5045 - 4 Piston CP6070 - 4 Piston GENERAL INFORMATION APPLICATIONS. - Grand AM GT Class. FEATURES. - Radial mount, - Two piece cast aluminium alloy body with Hard anodised surface treatment. - To suit Ø355.0 or 330.0mm x 26.0mm disc. - Differential bores, to control pad taper. - Stainless steel pistons with high temperature seals. - Stainless steel bridge pipe, pad abutments & wear plates fi tted. - Quick release pad retainer clip. - 7lb Anti-knockback springs fi tted as standard. PART NUMBERS. - CP5045-8S7L RHT / -9S7L LHT / -10S7L RHL / -11S7L LHL. CALIPER HANDING. It is important to select the correct ‘hand’ of caliper. See note on page 4 for guidance. PAD INFORMATION - Pad Family = CP5045D61 - Pad Area = 74.0cm² - Pad Depth = 60.5mm - Pad Thickness = 24.0mm INSTALLATION DRAWING R5 MAX R4 MAX R3 MIN R2 MIN R1 MIN W1 MAX W2 MAX W3 MAX W4 MAX W5 MAX W5 MAX W6 MAX RADIAL PROFILE (SCALED FOR A Ø330 DISC) R6 MAX 193.0 MAX TO REMOVE OADS 63.5 ‘PL’ DIM’N 35.74 2 OFF HOLES FOR ‘LOCK WIRING’ PAD RETAINING CLIP IN PLACE. 13.0 MAX THREAD TYPICAL MTG TIGHTENING TORQUE FOR GUIDANCE ONLY: M12 - 65Nm & M10 - 54Nm AP RACING RECOMMEND THAT PAD RETAINING CLIP IS ‘LOCK WIRED’ IN PLACE WHEN RUNNING VEHICLE TECHNICAL SPECIFICATION Piston Sizes Disc Diameter Ø38.1mm Ø44.5mm Max Ø355.0mm Min Ø330.0mm Disc Thickness 26.0mm Weight No Pads 3.2Kg Hydraulic Thread 3/8”x24UNF Mounting Type Radial Mtg centres 180.0mm Mtg offset 42.0mm Mtg hole Ø 12.1mm ‘PL’ Dimension 63.5mm Seal Repair Kit CP4518-JL Bleed Screw Tightening Torque Typical Mounting Bolt Torque 17Nm (12.5lbs/ft) M12 = 65Nm SPARE PARTS Pistons Ø38.1mm CP5045-110 Ø44.5mm CP5045-111 AKB Spring Kit CP6518- 7LBLL Pad Retainer Clip Retainer Part No CP3714-113 Hinge Retainer CP3714-112 Wear Plates x 4 CP3714-153 Bleed Screw CP3880-2 Fluid Pipes CP5045-7 131.7 (5.18”) 136.0 MAX 136.80 MAX Ø38.1 (1.5”) BORE LEADING Ø44.45 (1.75”) BORE - TRAILING DIRECTION OF DISC ROTATION DISC & WHEEL CENTRE LINE 180.0 MOUNTING HOLE CTR’S HYDRAULIC INLET 3/8X24”UNF Ø12.15 12.05 0.60X45° (2 PLACES) R180.0 PATHWAY RADIUS Ø25.0 75.0 (2.95”) 40.0 ‘U’ DIM’N 42.0 OFFSET BLEEDSCREW MAX TIGHTENING TORQUE 17Nm Disc Ø R1 R2 R3 R4 R5 R6 W1 W2 W3 W4 W5 W6 EFF ‘U’ RAD DIM’N 355x26 114.3 117.0 142.0 174.3 198.3 174.0 84.8 88.5 46.6 46.6 53.0 81.1 147.0 114.0 330x26 102.3 104.5 132.0 162.3 189.5 162.0 84.8 88.5 42.1 42.1 53.0 80.9 135.0 101.5 GENERAL INFORMATION APPLICATIONS - GT Rear, 180mm Centres. FEATURES - Radial mount. - To suit for Ø356.0 x 35.0mm Carbon disc & Ø356.0 x 32.0mm Iron disc. - Monobloc aluminium alloy body, CNC machined billet. - Differential bores, to control pad taper. - Titanium pistons. - High temperature seals. - Optional extras, - Dry-break fi ttings & body Thermo-Sensor. - Ceramic piston insulation caps. - Hard anodised surface treatment. - Stainless steel bridge pipe, pad abutments & wear plates fi tted. PART NUMBERS - CP6070-2S7MP RHT / -3S7MP LHT /-4S7MP RHL /-5S7MP LHL. CALIPER HANDING It is important to select the correct ‘hand’ of caliper. See note on page 4 for guidance. PAD INFORMATION - Iron Family = CP6070D49 - Carbon Family = CP6070 - Pad Area = 83.0cm² - Iron = 61.6cm² - Carbon = 69.1cm² - Pad Depth = 49.0mm - Pad Thickness = 25.0mm INSTALLATION DRAWING TECHNICAL SPECIFICATION Piston Sizes Ø28.6mm Ø36.0mm Disc Diameter Disc Thickness Ø356.0mm Carbon 35.0mm Iron 32.0.0mm Weight No Pads 2.2Kg Hydraulic Thread M10x1.0 Mounting Type Radial Mtg centres 180.0mm Mtg offset 42.0mm Mtg hole Ø 12.15mm ‘PL’ Dimension 63.5mm Seal Repair Kit CP4518-DH Bleed Screw Tightening Torque www.apracing.com +44 (0)24 7663 9595 201.00 MAX 174.50 MAX 124.80 MIN 86.75 MAX 95.00 MAX 44.20 MAX 44.20 MAX 22.10 22.10 54.00 MAX 54.00 MAX RADIAL PROFILE (SCALED FOR A Ø355.0 DISC) DRY-BREAK FITTING OPTION APPLY LOCTITE 270 TO THREAD UPON ASSEMBLY TIGHTENING TORQUE CP6300-6 FITTING (CALIPER) CP6300-7 FITTING (BLEEDING SYSTEM) CP6300-8 SPARE DUST CAP * SEAL 127.60 MIN 171.80 MAX 196.10 MAX TYPICAL MTG TIGHTENING TORQUE FOR GUIDANCE ONLY:M12 - 65Nm & M10 - 54Nm 63.50 ‘PL’ DIMN 29.29 114.00 (’U’ DIMN) THERMO SENSOR (PT100 TYPE) CP6282-2 (RH) CP6282-3 (LH) 17Nm (12.5lbs/ft) SPARE PARTS Pistons Ø28.6mm CP6070-110 Ø36.0mm CP6070-111 Wear Plates. x 4 CP6070-107 Beam Wear Plate. x 1 CP6070-106 Bleed Screw CP3880-1 Fluid Pipes CP6070-2 / -3 CP6070-6 CP6070-4 / -5 CP6070-7 AVAILABLE OPTIONS Thermo Sensor Right Hand CP6282-2 Left Hand CP6282-3 Dry-Break Fittings Piston Caps See Page 5 Ø28.6mm CP6060-128 Ø36.0mm CP6292-155 Iron 131.6 (5.18”) Carbon 131.6 (5.18”) 59.00 (2.32”) 59.00 (2.32”) 129.00 MAX 125.50 MAX Ø22.00 R151.90 EFFECTIVE RADIUS R180.00 PATHWAY RADIUS DIRECTION OF DISC ROTATION R126.50 MIN 180.0 MOUNTING HOLE CTRS 10.75 MAX FULL THD 12.19 Ø 12.09 Ø22.00 Ø355.0 DISC & WHEEL CL M10x1.0 THD INLET PORT 1.25x45° MIN 39.20 34.20 42.00 OFFSET
Page 2 and 3: Contents AP Racing CONTENTS PAGE -
Page 4 and 5: Introduction TOMORROW’S TECHNOLOG
Page 6 and 7: General & Technical Information ‘
Page 8 and 9: Caliper Assemblies Caliper Spare Pa
Page 14 and 15: GENERAL INFORMATION APPLICATIONS -
Page 16 and 17: GENERAL INFORMATION APPLICATIONS -
Page 20 and 21: GT Brake Calipers CP6071 - 4 Piston
Page 22 and 23: New Product Japanese GT CP6086 - 6
Page 24 and 25: Rally Brake Calipers CP6340 - 4 Pis
Page 26 and 27: Rally Brake Calipers CP6564 - 4 Pis
Page 28 and 29: Rally CP6760 - 4 Piston GENERAL INF
Page 30 and 31: Single Seater Brake Calipers CP7030
Page 32 and 33: Touring Car CP5789 - 4 Piston GENER
Page 34 and 35: Pro 5000+ CP5040-10/-11/-12/-13S4 4
Page 36 and 37: Pro 5000+ CP5060-2/-3/-4/-5S4 6 Pis
Page 38 and 39: Historic Brake Calipers AP Racing
Page 40 and 41: US Stock Car Brake Calipers CP5830
Page 42 and 43: Road Brake Calipers CP5200 - 4 Pist
Page 44 and 45: Road Brake Calipers CP5570- 6 Pisto
Page 46 and 47: Competition Brake Kits AP Racing, t
Page 48 and 49: APPLICATION. YEAR. KIT PART No. CAL

CP6070-2S7MP

Create successful ePaper yourself

Delete template?

Save as template?