service manual personal audio system

SERVICE MANUAL
Ver. 1.4 2006.03
US and foreign patents licensed from Dolby Laboratories.
AUDIO POWER SPECIFICATIONS
(US model only)
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION
With 3.2-ohm loads, both channels driven from
150 - 6,300 Hz; rated 1.8 W per channel-minimum
RMS power, with no more than 10 % total
harmonic distortion in AC operation.
Other Specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of about
200 mm from the objective lens surface on the optical
pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20 000 Hz +0/–1 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
US, CND, E, MX, TW models:
FM: 87.5 - 108 MHz
AM: 530 - 1710 kHz
9-879-649-05
2006C05-1
© 2006.03
Sony Corporation
Personal Audio Division
Published by Sony Techno Create Corporation
SPECIFICATIONS
SP, KR, TH, AUS models:
FM: 87.5 - 108 MHz
AM: 531 - 1611 kHz (9 kHz step)
530 - 1610 kHz (10 kHz step)
IF
FM: 10.7 MHz
AM: 450 kHz
Antennas
FM: Telescopic antenna
AM: Built-in ferrite bar antenna
General
Speaker
Full range: 10 cm (4 in.) dia., 3.2 Ω, cone type (2)
Input
LINE IN jack (stereo minijack):
Minimum input level 330 mV
Outputs
Headphones jack (stereo minijack):
For 16 - 64 Ω impedance headphones
Power output
2.3 W + 2.3 W (at 3.2 Ω, 10 % harmonic
distortion)
Power requirements
For player:
US, CND, E, MX, TW models:
120 V AC, 60 Hz
SP, TH, AUS models:
230 V AC, 50 Hz
KR model:
220 V AC, 60 Hz
9 V DC, 6 size D (R20) batteries
For remote control:
3 V DC, 2 size AAA (R03) batteries
Power consumption
16 W
ZS-SN10
US Model
Canadian Model
E Model
Australian Model
Model Name Using Similar Mechanism CFD-E95
Optical Pick-up Block Name KSM-213CDP
Optical Pick-up Name KSS-213C
Battery life
For player:
CD playback
Sony R20P: approx. 2 h
Sony alkaline LR20: approx. 8 h
Radio reception
Sony R20P: approx. 10 h
Sony alkaline LR20: approx. 25 h
Dimensions
Approx. 500 × 145 × 230 mm (w/h/d)
(19 3 /4 × 5 3 /4 × 9 1 /8 inches) (incl. projecting parts)
Mass
Approx. 3.8 kg (8 lb. 6 oz) (incl. batteries)
Supplied accessories
AC power cord (1) (US, CND, E, MX, TW models)
Mains lead (1) (SP, KR, TH, AUS models)
Remote control (1)
CD-ROM (SonicStage) (1)
SonicStage Installation/Operating Guide (1)
Design and specifications are subject to change without
notice.
• Abbreviation
AUS : Australian model
CND: Canadian model
KR : Korean model
MX : Mexican model
SP : Singapore model
TH : Thai model
TW : Taiwan model
PERSONAL AUDIO SYSTEM

ZS-SN10
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
2
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
0.15 µF
To Exposed Metal
Parts on Set
1.5 kΩ
AC
voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
TABLE OF CONTENTS
1. SERVICING NOTES ................................................ 3
2. GENERAL ................................................................... 4
3. DISASSEMBLY
3-1. Disassembly Flow ........................................................... 6
3-2. Cabinet Top Assy ............................................................. 6
3-3. MAIN Board.................................................................... 7
3-4. Cabinet Front Assy .......................................................... 7
3-5. LCD Board ...................................................................... 8
3-6. CD Block Assy ................................................................ 8
3-7. Optical Pick-up (KSS-213C) ........................................... 9
3-8. CD Lid ............................................................................. 9
4. ELECTRICAL ADJUSTMENTS .......................... 10
5. DIAGRAMS
5-1. Block Diagram – CD Servo Section – ............................ 12
5-2. Block Diagram – TUNER Section – .............................. 13
5-3. Block Diagram – MAIN Section – ................................ 14
5-4. Printed Wiring Board – CD Board – .............................. 16
5-5. Schematic Diagram – CD Board – ................................. 17
5-6. Printed Wiring Board – TUNER Board – ....................... 18
5-7. Schematic Diagram – TUNER Board – ......................... 19
5-8. Printed Wiring Boards – MAIN Section – ..................... 20
5-9. Printed Wiring Boards – POWER Section – .................. 21
5-10. Schematic Diagram – MAIN Section (1/2) – ................. 22
5-11. Schematic Diagram – MAIN Section (2/2) – ................. 23
5-12. Printed Wiring Boards – PANEL Section –.................... 24
5-13. Schematic Diagram – PANEL Section – ........................ 25
6. EXPLODED VIEWS
6-1. Cabinet Section................................................................ 33
6-2. Cabinet Front Section ...................................................... 34
6-3. Cabinet Top Section-1 ..................................................... 35
6-4. Cabinet Top Section-2 ..................................................... 36
6-5. Cabinet Bottom Section................................................... 37
6-6. Optical Pick-up Section (KSM-213CDP) ....................... 38
7. ELECTRICAL PARTS LIST .................................. 39
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.

NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup
block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the leadfree
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SECTION 1
SERVICING NOTES
ZS-SN10
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
During normal operation of the equipment, emission of the laser
diode is prohibited unless the upper lid is closed while turning ON
the S801. (push switch type)
The following checking method for the laser diode is operable.
• Method
Emission of the laser diode is visually checked.
1. Open the upper lid.
2. Push the S801 as shown in Fig.1.
Note: Do not push the detection lever strongly, or it may be bent or damaged.
3. Press the u button.
4. Check the object lens for confirming normal emission of the
laser diode. If not emitting, there is a trouble in the automatic
power control circuit or the optical pick-up.
In this operation, the object lens will move up and down 2
times along with inward motion for the focus search.
S801
Fig.1 Method to push the S801
3

ZS-SN10
4
Basic Operations
Playing a CD
Connect the supplied AC power cord.
1 Press PUSH Z OPEN/CLOSE to
open the CD lid and place the CD on
the CD tray.
2 Press PUSH Z OPEN/CLOSE to
close the CD lid.
Notes
• If ATRAC3plus files and
MP3 files are recorded on
the same CD, this CD
player plays the
ATRAC3plus first.
• The playback capability of
this CD player may vary
depending on the quality of
the disc and the condition of
the recording device.
• Characters that can be
displayed on this CD player
are listed below.
–A to Z
–a to z
–0 to 9
–! " # $ % & ' ( ) * + , - . / :
; < = > ? @ [ \ ] ^ _ ` { | }
~
If you use other characters
on your computer using
software such as
SonicStage, they are
displayed as “–” on this CD
player.
• On a disc that has
ATRAC3plus/MP3 files, do
not save files in other
formats and do not make
unneccessary groups.
3
1, 2
With the label side up
To Press
select a group* 2 + to go forward and – to go
backward
remove the CD PUSH Z OPEN/CLOSE* 3
turn on/off the player POWER
* 2 This function works for ATRAC CDs/MP3 CDs only.
* 3 Once you open the CD lid, the track to start play will change to
the beginning of the first track.
The structure of ATRAC CDs/MP3 CDs
ATRAC CDs/MP3 CDs consist of “files” and “groups.” A
“file” is equivalent to a “track” of an audio CD. A “group”
is a bundle of files and is equivalent to an “album.”
For MP3 CDs, this CD player recognizes an MP3 folder as
a “group” so that ATRAC CDs and MP3 CDs can be
operated in the same way.
In this manual, we use the word “track” in description of
the operations available for both ATRAC CDs/MP3 CDs
and audio CDs, and the word “file” for the operations
available for ATRAC CDs/MP3 CDs only.
Playing order of ATRAC CDs and MP3 CDs
For ATRAC CDs, files are played in the order selected in
SonicStage.
For MP3 CDs, the playing order may differ depending on
the method used to record MP3 files on the disc. In the
following example, files are played in order of 1 to 7.
Group
File
ATRAC CD
MP3 CD
SECTION 2
GENERAL
3 Press u (N on the remote) (direct
power-on).
The player plays all the tracks once.
Display
Audio CD
ATRAC CD/MP3 CD*
Note
Before playing an ATRAC
CD/MP3 CD, this player
reads all file and group
information on the CD.
Depending on the file
structure, it may take more
than a minute to read them.
During this time, “Reading”
is displayed.
Tips
•To listen through
headphones, connect the
headphones to the i
(headphones) jack.
•Playback starts from the
track you last stopped
playing (Resume play).
To cancel the resume play
to start play from the
beginning of the first track,
press x in stop mode.
This section is extracted from
instruction manual.
Track number Playing time
File name
File number Playing time
*When playing an MP3 CD, “MP3”
appears in the display.
Use these buttons for additional operations
POWER
u
x
VOLUME –, +
i
>
.
–, +
To Press
adjust the volume VOLUME +* 1 , – (VOL +* 1 , – on the
remote)
stop playback x
pause playback u* 1 (X on the remote)
Press the button again to resume play after
pause.
go to the next track >
go back to the .
previous track
* 1 The button has a tactile dot.
Notes on ATRAC CDs
•Maximum number of groups: 255
Maximum number of files: 999
• CD-Rs/CD-RWs recorded in the ATRAC3plus format cannot be
played on your computer.
Notes on MP3 CDs
•Maximum number of groups: 255
Maximum number of files: 511
Maximum directory level: 8
•A group that does not include an MP3 file is skipped.
• Be sure to add the file extension “mp3” to the file name.
However, if you add the file extension “mp3” to a file other than
an MP3 file, the player will not be able to recognize the file
properly.
• This player can play bit rates of 32 to 320 kbps, and sampling
frequencies of 32/44.1/ 48 kHz.
•To compress a source in an MP3 file, we recommend setting the
compression parameters to “44.1 kHz,” “128 kbps,” and
“Constant Bit Rate.”
•To record up to the maximum capacity, set the writing software
to “halting of writing.”
•To record to the maximum capacity at one time up on media that
has nothing recorded on it, set the writing software to “Disc at
Once.”

Listening to the radio
1 2
Connect the supplied AC power cord.
1 Press RADIO•BAND•AUTO
PRESET repeatedly until the band
you want appears in the display
(direct power-on).
2 Hold down TUNE + or – until the
frequency digits begin to change in
the display.
The player automatically scans the
radio frequencies and stops when it
finds a clear station.
If you can’t tune in a station, press
TUNE + or – repeatedly to change
the frequency step by step.
Display
Indicates an FM
stereo broadcast
Tip
If the FM broadcast is noisy,
press MODE repeatedly until
“Mono” appears in the
display and radio will play in
monaural.
Use these buttons for additional operations
To Press
adjust the volume VOLUME +*, – (VOL +*, – on the
remote)
turn on/off the radio POWER
* The button has a tactile dot.
To improve broadcast reception
Reorient the antenna for FM. Reorient the player itself for
AM.
for FM
POWER
VOLUME –, +
MODE
for AM
ZS-SN10
5

ZS-SN10
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
6
SET
3-2. CABINET TOP ASSY
(Page 6)
3-3. MAIN BOARD
(Page 7)
3-4. CABINET FRONT ASSY
(Page 7)
3-5. LCD BOARD
(Page 8)
Note: Follow the disassembly procedure in the numerical order given.
3-2. CABINET TOP ASSY
qs cabinet top assy
7 three screws
(B3)
qa flexible flat cable (4 core)
(CN403)
0 wire (flat type) (23 core)
(CN102)
SECTION 3
DISASSEMBLY
3-6. CD BLOCK ASSY
(Page 8)
3-7. OPTICAL PICK-UP
(KSS-213C)
(Page 9)
4 three screws
(B3)
3 Open the CD lid.
8
3-8. CD LID
(Page 9)
2 telescopic antenna (ANT1)
5 Lift the handle.
1 screw (M3)
9 connector
6 two screws
(B3)

3-3. MAIN BOARD
4 flexible flat cable
(11 core) (CN806)
3-4. CABINET FRONT ASSY
1 connector
(CN323)
5 flexible flat cable
(11 core) (CN807)
8 MAIN board
3 two screws
(B3)
2 two screws
(B3)
3 connector (CN901)
2 connector (CN301)
7 two screws
(B2.6)
1 connector (CN302)
4 five screws
(B3)
5 screw (B3)
6 flexible flat cable
(11 core) (CN801)
6 cabinet front assy
ZS-SN10
7

ZS-SN10
3-5. LCD BOARD
3-6. CD BLOCK ASSY
8
6 two screws
(B2.6)
2 CD block assy
5 four screws
(B2.6)
1 four screws
2 speaker box (L)
7 two screws
(B2.6)
8 LCD board
1 four screws
(B3)
3 four screws
(B3)
4 speaker box (R)

3-7. OPTICAL PICK-UP (KSS-213C)
3-8. CD LID
3 sled shaft
2 gear (A)
7 boss
1 claw
2 CD spring
5 optical pick-up
(KSS-213C)
5
4 damper
9 CD lid
1 CD cover
3 screw (B2.6)
4 flexible flat cable (16 core)
6 claw
8 boss
ZS-SN10
9

ZS-SN10
Ver. 1.1
TUNER SECTION 0 dB=1 µV
[AM]
Setting:
Function: RADIO
RADIO/BAND, AUTO PRESET button: AM
[FM]
Setting:
Function: RADIO
RADIO/BAND, AUTO PRESET button: FM
10
AM RF signal
generator
30% amplitude
modulation by
400 Hz signal
Output level:
as low as possible
FM RF signal
generator
75 kHz frequency
deviation by 1 kHz
signal
Output level:
as low as possible
Put the lead-wire
antenna close to
the set.
0.01 µF
TUNER board
TP (VT)
TP (GND)
set
TUNER board
TP (ANT)
set
TUNER board
TP (GND)
100 kΩ
• Repeat the procedures in each adjustment several times, and
the tracking adjustments should be finally done by the trimmer
capacitors.
• Remove FM antenna in FM adjustment.
SECTION 4
ELECTRICAL ADJUSTMENTS
32 Ω
level meter
+
–
i jack (J301)
32 Ω
level meter
+
–
i jack (J301)
digital voltmeter
AM IF ADJUSTMENT
Adjust for a maximum reading on level meter
T1 450 kHz
( ): Singapore, Korean, Thai and Australian models
AM FREQUENCY COVERAGE ADJUSTMENT
Adjustment Part Frequency Display Reading on Digital Voltmeter
L4 530 kHz (531 kHz) 1.0 ± 0.05 V
Confirmation
1,710 kHz
(1,611 kHz)
5.3 ± 0.7 V (5.2 ± 0.6 V)
( ): Singapore, Korean, Thai and Australian models
AM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter
L3 620 kHz (621 kHz)
CT3 1,400 kHz (1,404 kHz)
FM IF ADJUSTMENT
Adjust for a minimum reading on level meter
T2 10.7 MHz
FM FREQUENCY COVERAGE ADJUSTMENT
Adjustment Part Frequency Display Reading on Digital Voltmeter
L2 108 MHz 3.0 ± 0.2 V
Confirmation 87.5 MHz 1.3 ± 0.3 V
FM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter
L1 87.5 MHz
CT1 108 MHz
Adjustment and Connecting Location: TUNER board
(See page 11)

ZS-SN10
Adjustment and Connecting Location:
– TUNER Board (Component Side) –
L4
AM Frequency Coverage Adjustment
L2
FM Frequency Coverage Adjustment
– TUNER Board (Conductor Side) –
TP
(VT)
TP
(GND)
CT3
L3
TP
(ANT)
T2 FM IF Adjustment
T1 AM IF Adjustment
L1
CT1
AM Tracking Adjustment
FM Tracking Adjustment
11
CD SECTION
FOCUS BIAS CHECK
1. Connect the oscilloscope to TP (RFACO) and TP (VC) on the
CD board.
2. Insert the disc (PATD-012). (Part No.: 4-225-203-01)
3. Press the u button.
4. Confirm that the oscilloscope waveform is as shown in the
figure below. (eye pattern)
A good eye pattern means that the diamond shape (◊) in the
center of the waveform can be clearly distinguished.
• RF signal reference waveform (eye pattern)
11
VOLT/DIV: 0.2 V (with the 10: 1 probe in use.)
TIME/DIV: 200 ns
0.5 to 1.1 Vp-p
When observing the eye pattern, set the oscilloscope
for AC range and raise vertical sensitivity.
Checking Location:
– CD Board (Conductor Side) –
TP
(VC)
IC201
TP
(RFACO)
ZS-SN10

ZS-SN10
5-1. BLOCK DIAGRAM – CD SERVO SECTION –
ZS-SN10
OPTICAL
PICK-UP BLOCK
(KSM-213CDP)
M402
(SLED)
2-AXIS
DEVICE
M
M401
(SPINDLE) M
A
B
C
D
E
F
LD
PD
FCS+
FCS–
TRK+
TRK–
SL+
SL–
SP+
SP–
SECTION 5
DIAGRAMS
AUTOMATIC
POWER CONTROL
Q321
FOCUS/TRACKING COIL DRIVER,
SLED/SPINDLE MOTOR DRIVER
IC402
12 CH2OUTF CH2FIN 6
11 CH2OUTR
13 CH1OUTR
14 CH1OUTF
17 CH3OUTF
18 CH3OUTR
16 CH4OUTF
15 CH4OUTR
MUTE
20
CH2RIN 7
CH1RIN 5
CH1FIN 4
CH3FIN 23
CH3RIN 22
OPIN+ 2
OPOUT 27
CH4IN 24
57
58
59
60
50
51
66
67
45
A
B
C
D
E
F
LD
PD
FFDR
46 FRDR
44 TRDR
43 TFDR
41
42
38
SFDR
SRDR
MDP
RFACO
70 71 RFACI
12
CD DSP
IC201
XRST
8
12
AOUT1 112
AOUT2 117
XTAI 109
XTAO 108
SSTP 39
X202
16.9344MHz
S201
(LIMIT)
CD +3.3V
DATA 89 19 DATA
CLOK 11
20 CLOK
XLAT 16
55 XLAT
SENS 20
18 SENS
SCOR 26 56 SCOR
58 IDATA2
DATA2 12
59 ODATA2
CLOK2 90 60 CLOK2
XLAT2 13
61 XLAT2
REQ 14
62 REQ
IREQ 10
57 IREQ
ACK 15 63 ACK
XTACN 7
67 XTACN
S801
(CD LID OPEN/CLOSE DETECT)
R-CH
68 XRST
66 M-MUTE
53 CD-DOOR
SYSTEM CONTROLLER
IC801 (1/2)
CD-L
• R-ch is omitted due to same as L-ch.
• SIGNAL PATH
: CD PLAY
A
(Page 14)

ZS-SN10
5-2. BLOCK DIAGRAM – TUNER SECTION –
ANT1
FM TELESCOPIC
ANTENNA
L1
FM RF
CT1, L1
FM TRACKING
L3
AM FERRITE-ROD
ANTENNA
CT3, L3
AM TRACKING
• R-ch is omitted due to same as L-ch.
• SIGNAL PATH
: FM
: AM
CT1
CT3
X1
75kHz
D1
D3
(1/2)
20
19
2
24
22
XOUT
XIN
FM
RF-IN
FM
RF-OUT
AM
RF-IN
FM/AM RF AMP, MIX, OSC,
FM/AM IF AMP, DET, MPX
IC1
FM
RF AMP
AM
RF AMP
AM FREQUENCY
COVERAGE
L4
AM
OSC
D3
(2/2)
REFERENCE
DIVIDER
FM/AM PLL
IC2
FM
MIX
FM
OSC
AM
MIX
AM
OSC
AM OSC
FM OSC
20 21
MW/LW 6
BUFFER
BUFFER
LP-OUT
18
MIX-OUT
D2
OSC
-OUT
LOW-PASS
FILTER
LOW-PASS
FILTER
UNLOCK
DETECT
CF2
4 7
19
FM FREQUENCY
COVERAGE
VT B+
L2
FM OSC
LP-IN
17 16
PD
PHASE
DETECTOR/
CHARGE PUMP
12 BIT
PROGRAMMABLE
DIVIDER
T1
AM IFT
AM IF
CF4
SWALLOW
COUNTER
FM IN
12
1/2
13
AM IN
11
6
FM
IF-IN
AM
IF-IN
FM IF
AMP
AM IF
AMP
IF
BUFFER
IF-OUT
IF IN
SHIFT REGISTER & LATCH
13
QUAD
10
FM
DET
AM
DET
UNIVERSAL
COUNTER
T2
FM IFT
FM IF
AF
BUFFER
LEVEL
DET
DET
-OUT
16
ST
IND
ST-IND
17 18
10 8 9
ST-IND
BAND
BAND 7
MO/ST 13
CCB
INTERFACE
MPX
-IN
15
DI
CL
CE
DO
2
3
1
4
AF
AMP
L-OUT
MPX MUTE
R-OUT
12
11
LPF1/BAND
LPF2/MO-ST
13 14
MUTING
Q808
STEREO/
MONO,
FM/AM
R MUTING
R DATA
R CLOCK
R CE
R COUNT
R-CH
TU-L B
R DATA, R CLOCK, R CE,
R COUNT, R MUTING
C
ZS-SN10
(Page 14)
(Page 14)

ZS-SN10
5-3. BLOCK DIAGRAM – MAIN SECTION –
C
(Page 13)
(Page 12) A
CD-L
6 CD-L
SEL L 4
(Page 13) B
TU-L
8 RA-L
R DATA, R CLOCK,
R CE, R COUNT,
R MUTING R DATA
R CLOCK
R CE
R COUNT
R MUTING
ZS-SN10
Q802
X1
J322
LINE IN
28 R-DATA
29 R-CLOCK
30 R-CE
27 R-COUNT
31 R-MUTE
X801
4.19MHz
X0
83 82
Q801, 802
SHIFT CLOCK
Q801
SHIFT
78
R-CH
SYSTEM CONTROLLER
IC801 (2/2)
X1A
X0A
79 80
X802
32.768kHz
10 LI-L
BL
100
SI
9
VOL-DATA
LED DRIVE
Q803
D402
(LCD BACK LIGHT)
SC
14 13
10
VOL-CLK
LCD-DB0 – LCD-DB7
85 – 92
LIQUID CRYSTAL DISPLAY
LCD401
SYS +3.3V
S402 – 407
S410 – 414, 425
S418 – 424
LCD-RS
LCD-E
LCD-RW
LCD-RES
96 95 94 93
REMOTE CONTROL
RECEIVER
IC401
EEPROM
IC804
(JOG)
1 R-IN
LCH 16
INPUT SELECT,
ELECTRICAL VOLUME,
SURROUND/TONE CONTROL
IC301
SDA
SCL
ROTARY
ENCODER
S401
WAKE UP
SWITCH
Q807
5
6
D301
MEGA BASS
CONTROL
Q101
8
7
15
MEGABASS
64 REMOTE
EEP-SDA
EEP-SCL
98 JOG-A
99 JOG-B
52 WP
41 KEY0
39 KEY1
40 KEY2
R-CH
14
MUTING
Q121
21
A-MUTE
R-CH
CD +2.5V
POWER
AMP
IC304
3.3V-CHECK 43
BUCKUP-ON 26
CD3.3V-ON 25
P-CON 22
VH 45
VH-CONT 69
LOAD 70
VM 46
VM-CONT 32
VOL-CHECK 44
TU-ON 24
RESET 77
AC-IN 54
+2.5V
REGULATOR
IC202
14
CD +3.3V CD +6V
DC LEVEL
DETECT
Q821, 822
DC LEVEL
DETECT
Q811, 812
AC CHECK
Q805
B+ SWITCH
Q813
RE B+
DC/DC
CONVERTER
IC901, Q956
E.VOL B+
RADIO +6V
R-CH
SYS +3.3V
B+ SWITCH
Q804, 806
LOAD CONTROL
SWITCH
Q823, 824
B+ SWITCH
Q809, 810
RESET SIGNAL
GENERATOR
IC803
SP101
(L-CH)
SP201
(R-CH)
+6V
REGULATOR
Q954
D401
OPR/
BATT
RMC +5V
SYS +3.3V
AU +6V
SYS +3.3V
J301
i
D801
SW +9V
+6V
REGULATOR
Q955
+3.3V
REGULATOR
IC802
• R-ch is omitted due to same as L-ch.
• SIGNAL PATH
: FM
B+ SWITCH
Q951 – 953
: CD PLAY
AMP B+
RECT
D901 – 904
F902
T901
POWER
TRANSFORMER
J901
AC IN
DRY BATTERY
SIZE "D"
(IEC DESIGNATION R20)
6PCS. 9V

ZS-SN10
• Note for Printed Wiring Boards and Schematic Diagrams
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
• W : indicates side identified with part number.
• f : internal component.
• : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from
(Conductor Side) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(Component Side) the parts face are indicated.
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1 /4 W or less unless otherwise
specified.
• f : internal component.
• C : panel designation.
Note:
The components identified
by mark 0 or dotted
line with mark 0 are
critical for safety.
Replace only with part
number specified.
Note:
Les composants identifiés
par une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce portant le numéro
spécifié.
• A : B+ Line.
• H : adjustment for repair.
• Power voltage is dc 4.5V and fed with regulated dc power
supply from pin 1 and 2 of CN902 on the BATTERY 1
board, and from pin 3 and 2 as well.
no mark : FM
〈〈 〉〉 : AM
( ) : CD PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : FM
f : AM
J : CD PLAY
j : LINE IN
• Abbreviation
AUS : Australian model
CND : Canadian model
KR : Korean model
MX : Mexican model
SP : Singapore model
TH : Thai model
TW : Taiwan model
15
• Circuit Boards Location
15
CONTROL (1) board
BATTERY 1 board
LCD board
POWER board
H/P board
CD board
CONTROL (2) board
MAIN board
TUNER board
BATTERY 2 board
ZS-SN10
Ver. 1.1

ZS-SN10
5-4. PRINTED WIRING BOARD – CD BOARD – • See page 15 for Circuit Boards Location. :Uses unleaded solder.
A
B
C
D
E
F
G
H
I
ZS-SN10
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
CD BOARD (COMPONENT SIDE)
R401
C110
C201 X202
R201
C202
R207
C101
C102
C108
R202
C401
C424
IC202
C203
C226
C269
R423
3
1
C406
C227
R421
C270
C204
R115
C268
C267
C275
R271
C215
R276
R203
C219
C272 C104
C271
C223
C220
R260
C321
C105
C210
C232
C206
R256
Q321
C107
C109
C257
R249
R323
E
C322
C205
R325
R322
R321
R324
R326
C207
C323
1-865-539-
11
(11)
16
CD BOARD (CONDUCTOR SIDE)
16
C252
C254
C251
R253
R255
C253
R252
R254
C256
C224
R101
C208
R452
R102
R107
R109
R108
R451
C259
IC201
R250
C258
C230
CN301
R104
R257
C260
OPTICAL PICK-UP
BLOCK
(KSM-213CDP)
C103
C451
R105
R110
R103
R259
C264
R258
C261
M
R278
R265
R268
C221
M401
(SPINDLE)
IC402
R277
R275
R267
R266
C273 C265
C303
C213
C217
C218
C222
S201
(LIMIT)
R292
C214
R270
C302
C301
C292
C291
R291
R280
C112
C113
C111
C405
C404
R112
R113
R111
C133
1-865-539-
C132
11
(11)
M
CN102
M402
(SLED)
A
MAIN BOARD
CN801
(Page 20)

17
17
ZS-SN10
ZS-SN10
5-5. SCHEMATIC DIAGRAM – CD BOARD – • See page 26 for IC Block Diagram. • See page 26 for Waveforms. • See page 28 for IC Pin Function Description.
R259
C208
TP3
C205
R324
R101
C214
R271
R270
R292
C110
R451
R102
R103
R104
R105
R107
R108
R109
R110
R111
R255
R253
TP4
C406
C301
R325
R326
R254
R252
R250
R268
R322
R321
C264
CN102
R257
CN301
C222
C269
C213
C270
C268
C275
C215
R203
R291
C201
C219
R112
R113
C203
C108
C102
C101
C111
C104
C109
C107
R275
R277
R276 C271
C220
C221
C273
C261
C260
C259
R265
R266
R267
R258
C258
R260
C256
C207
C254
C253
C252
C251
C232
C206
C224
C267
C218
C291
C292
C217
C202
R401
C401
C302
C303
C322
C321
R323
TP1
TP2
R421
C404
IC201
R207 C226
X202
C265
R249
C210
R256
C257
C323
Q321
C424
R423
C405
M402
M401
IC402
IC202
C227
S201
TP
C230
TP
C451
R452
R115
R201
R202 C204
C112
C113
C105
C103
R280
C272
R278
C223
C133
C132
10k
0.1
TEI
0.1
100k
100
0.1
1M
470
100
220p
22k
100
100
100
100
100
100
100
100
100
1k
1k
FEI
0.1
0.1
0
0
10k
10k
1M
10k
2.2
2.2
1000p
23P
470k
16P
0.1
47 4V
0.1
47 4V
22p
5p
0.1
0
100
100
10V
0.1
100
100
100
10V
220p
22p
22p
220p
220p
220p
220p
100
100
47k 0.1
0.1
0.1
470p
0.01
0.47
100p
4.7k
1k
4.7k
220k
220p
0
0.1
100 10V
4700p
470p
4700p
470p
0.1
0.1
0.1
22p
0.1
470p
470p
0.1
0.1
0
470
10V
10
10
1
1000p
0
APC
SPI
0
0.1
CXD3014-201R
0 1
16.9344MHz
0.1
47k
0.1
22k
0.1
100
10V
2SA2119K
0.1
10k
0.1
FAN8040G3
TK73325WTL-G
1
100p
47000p
10k
0
0
0 220p
100p
100p
100p
100p
0
0.1
100
47p
100p
22p
FRDR
FFDR
TRDR
TFDR
FRDR
FFDR
TRDR
TFDR
SP-
SP+
SL+
SL-
SP+
SP-
SL+
SL-
OPIN-
OPIN+
CH1FIN
CH1RIN
CH2FIN
CH2RIN
GND
CNF4
POWVCC
CH2OUTR
CH2OUTF
CH1OUTR
CH1OUTF
CH4OUTR
CH4OUTF
CH3OUTF
CH3OUTR
POWVCC
MUTE
GND
CH3RIN
CH3FIN
CH4IN
CH4CAPA
OPOUT
PREVCC
VREF GAIN-SW
MIRR
DFCT
FOK
VSS
LOCK
MDP
SSTP
IOVSS1
SFDR
SRDR
TFDR
TRDR
FFDR
FRDR
IOVDD1
AVDD0
AVSS0
E
F
TEI
TEO
FEI
FEO
VC
A
B
C
D
AVDD4
RFDCO
PDSENS
AC_SUM
EG_IN
LD
PD
RFC
AVSS4
RFACO
RFACI
AVDD3
BIAS
ASYI
ASYO
VPCO
VCTL
AVSS3
CLTV
FILO
FILI
PCO
BCKI
LRCKI
LRCK
VSS
PCMD
BCK
VDD
IOVDD2
DOUT
TEST
IOVSS2
XVSS
XTAO
XTAI
XVDD
AVDD1
AOUT1
VREFL
AVSS1
AVSS2
VREFR
AOUT2
AVDD2
IOVDD0
IOVSS0
XTACN
XRST
VSS
VDD
SENS
WFCK
XUGF
XPCK
GFS
C2PO
SCOR
VDD
COUT
PCMDI
CLOK
SVSS
SVDD
SVSS
SVDD
VSS
SVDD
VDD
VSS
TEST1
SVSS
SVSS
SVDD
JTAGTCK
JTAGTDI
JTAGTDO
JTAGTMS
TRST
VDD
TES1
PLLVDD
PLLVSS
ACK
REQ
IREQ
SRAMSTB
2 3
1
XLAT2
XLAT
CLOK2
DATA
DATA2
T+
VC
GND
LD
PD
F+
T-
F-
VCC
SCOR
SENS
XRST
XTACN
D-OUT
L-OUT
R-OUT
DVDD(3.3V)
AVDD(3.3V)
AGND
DGND
MGND
E
D
A
B
C
F
VR
XLAT
DATA
IN
GND
OUT
+2.5V REGULATOR
(LIMIT)
AUTOMATIC
POWER
CONTROL
CD DSP
FOCUS/TRACKING
COIL DRIVER,
SLED/SPINDLE
MOTOR DRIVER
OPTICAL
PICK-UP
BLOCK
(SPINDLE)
(SLED)
(VC)
(RFACO)
KSM-213CDP
CLOK2
M-MUTE
IREQ
CLOK
DATA2
XLAT2
REQ
ACK
6V
(Page 22)
Ver. 1.3

ZS-SN10
Ver. 1.2
5-6. PRINTED WIRING BOARD – TUNER BOARD – • See page 15 for Circuit Boards Location. :Uses unleaded solder.
A
B
C
D
E
F
B
MAIN
BOARD
CN802
(Page 20)
ZS-SN10
1 2 3 4 5 6 7 8 9 10
TUNER BOARD
1
11
TP
(VT)
TP
(GND)
IC2
L3
AM FERRITE-ROD
ANTENNA
18
L4
18
(US, CND, E, MX)
L2
(SP, TW, KR, TH, AUS)
(SHIELD CASE)
C77
JC24
C13
IC1
C78
(SP, TW, KR, TH, AUS)
L1
(US, CND, E, MX)
T1
T2
R5
TP
(ANT)
1-863-438-
ANT1
FM TELESCOPIC
ANTENNA
11
(11)

ZS-SN10
5-7. SCHEMATIC DIAGRAM – TUNER BOARD – • See page 26 for IC Block Diagrams. • See page 26 for Waveform.
ANT1
FM TELESCOPIC
ANTENNA
TUNER
JC24 L11 JC12 JC11
R41 C49
CT3
0 1µH 0 0
10k 0.01
(US, CND,E, MX)
(SP, TW, KR, TH, AUS)
TP
(ANT)
D11
1SS355
D10
1SS355
C32
D1
KV1471E
C34
0.01
L3
AM FERRITE-ROD
ANTENNA
1000p
R32
100k
CT1
L1
FM
RF
C35
0.01
FM FREQUENCY
COVERAGE
FM/AM RF AMP,MIX,OSC,
FM/AM IF AMP,DET,MPX
IC1
TA2149BN
C33
0.01
L2
D3
KV1520NT
(US, CND, E, MX)
FM
OSC
R2
470
C13
0.01
FM
RF-OUT
R3
10k
C10
1
50V
R31
4.7k
GND1
C1
47p
R40
220k
C37
0.01
R30
22k
D2
KV1471E
R33 C30
10k 0.01
VCC1
FM
RF-IN
C8
1000p
AM LOW
JC3 0
AM
RF-IN
CUT
C41
220p
C42
100p
C43
22p
C47 C39
10p 0.1
R1
470
C80
0.01
FM OSC
MIX-
OUT
C31
22p
JC13
0
C4
1000p
AM OSC
VCC2
T1
AM IFT
JC6
R5 0
1K
C11
0.1
OSC-
OUT
AM
IF-IN
R24
220
ST-IND
FM
IF-IN
CF4
C18
220
10V
L4
AM OSC
19
R50
1k
R91
220
R92
220
19
C51 C52 R51
22p 10p 10k
C61 C62 C63
100p 100p 100p
R61 R60 R59 R58
2.2k 2.2k 2.2k 2.2k
C29
100
10V
R10 47
R52 C53 R65
C65
R63
4.7
0 0.22 10k 10k
50V
R14
1k X1
75KHz
C59
100p
R55 R53
10K 4.7k
C95
1000p
C24 C22 C20
220p R11 0.1 0.1
2.2k
C55
100p
C23
1
50V
C21
1
50V
IF-OUT
GND2
CF2
DET-OUT
AGC
C12
4.7
50V
C9
10p
AM FREQUENCY
COVERAGE
MPX-IN
QUAD
T2
FM
IFT
LPF2
R-OUT
C7
5p
C14
∗
/MO-ST
LPF1
/BAND
L-OUT
C15
∗
C78
4700p
C77
4700p
(SP, TW, KR, TH, AUS)
∗C14, 15
0.01 (SP, TW, KR, TH, AUS)
0.022 (US, CND, E, MX)
JC4
0
JC33
0
JC2 0
JC34 0
11
XOUT
CE
XIN
DI
LP-OUT
CL
LP-IN
DO
PD
MUTE
JC1 0
C27 C26
100p 100p
VSS
MW/LW
C54
220
10V
R54
470
VDD
BAND
MO/ST
ST-IND
C56
1000p
C57
1000p
C66 C68
100p 100p
FM IN
BAND
AM IN
IF IN
IC2
LC72137M-TLM
C60
1000p
R94
1k
FM/AM PLL
TP
(GND)
TP
(VT)
R13
1k
R4 JC5
10k 0
R56
220
R57
100
L21
10µH
CNP1
11P
R-MUTE
R-COUNT
R-CLOCK
R-DATA
R-CE
TU-L
RADIO 6V
TU-R
A-GND
R-VT
S-GND
ZS-SN10
Ver. 1.2
B
MAIN
BOARD
(1/2)
CN802
(Page 22)

ZS-SN10
Ver. 1.2
5-8. PRINTED WIRING BOARDS – MAIN SECTION – • See page 15 for Circuit Boards Location. :Uses unleaded solder.
ZS-SN10
A
B
C
D
E
F
G
H
I
J
K
L
M
N
TUNER
BOARD
CNP1
(Page 18)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
B
C303
C104
R206
MAIN BOARD
R205
R105
C202
C324
R202
R309
R212
R210
C126
L804
C110
C208
CN302
C204
C102
C224
R125 R225
C109
C108
R211
R216
R214
R111
R112
R110
C125
R323
R113
C218
C118
R106
R124
JW316
JW315
CN805
C226
JW320
A
K
A
D301
C209
C212 C213
R215
C325 C124
C211
R213
C105
C205
C117
C217
JW317
R224
R219
C210
R217
C225
IC304
C203
C321
R324
IC301
R119
C106
C111
C322
C206
C207
C113
R116
C107
C223
JW314
C304
C103
R305
JW313
C114
C214
C123
JW890
JW805
Q952
JW888
JW889
JW806
C956
JW809
C954
JW808
C101
JW819
C201
C326
Q955
C953
JW875
JW876
JW877
JW884
JW842
JW883
JW843
JW882
JW841
JW881
JW804
Q954
C803
JW878
JW807
JW870
JW815
JW816
JW869
JW868
JW840
JW867
20
JW866
C963
C959
C961
C955
X801
JW839
JW864
X802
20
JW825
JW831
JW833
JW824
JW828
JW829
JW827
JW832
JW853
JW830
JW844
C870
R813
C837
JW847
R882
C841 JW848
R863
R884
JW849
JW850
R883
JW851
R845
R887
Q807
CN802 CN804
C868
R829
S801
CD LID
OPEN/CLOSE
DETECT
R227
R321
R118
R221
R117
C874
Q221
C112
R114
R218
R102
R101
R203
R223
R104
C301
R103
R201
R485
R483
C220
JW893
R115
R123
R222
C302
R127
Q201
R204
Q810
R220
C222
JW892
C122
R121
Q101
R306
JW886
JW885
JW891
JW318
C305
C306
R304
R486
R484
C120
R122
R120
R303
Q809
Q121
C116
C216
R301
R302
JW887
R322
R953
R952
R951
R950
Q951
R957
R958
Q953
JC808
D906
R955
R954
R902
JW319
R956
R903
R901
C907
CN807
C
R959
R960
R961
D905
R326
C960
R325
D907
LCD BOARD
CN405
(Page 24)
D951
D953
JW810
C951
C952
R488
L803
C423
C424
C427
C428
C431
C432
Q804
Q806
R817
JW813
JW814
C433
R816
C429
C425
R480
C802
C426
C430
C434
Q803
R481
L802
L801
C801
R468
R469
R470
R471
R472
R473
R474
R475
R476
R477
R478
R479
C421
C842
R815
R825
R826
R847
R848
C950
C805
JW312
C828
C827
Q802
JW822
C829
JW871
JW820
R895
C822
C830
JC801 C826
C831
R830
R833
JW865
C823
JW322
Q801
C824
C825
JW872
R802
(TW, KR, AUS)
JW873
C832
C833
R801
R803
JW874
(US, CND, E, MX) R806
R805
(SP, TW, KR, TH, AUS) R856
C851
CN806
R855
C862
C810 C861
C848
C849
D
R818
IC804
3
1
C422
5
8
LCD BOARD
CN402
(Page 24)
IC802
C845
(EXCEPT TW, KR, AUS)
C806
4
1
R878
R832
R837
R834
R838
JW863
C957
D908
JW812
C958
JW803
JC803
R896
C821
C872
C871
JW858
JW899
JW862
3 1
4 5
IC801
R835
JW861
JW823
IC803
R893
R900
1
2
R839 R840
C850
JW860
JW321
IC901
Q956
4
3
R891
C869
R842
R841
R894
C855
C856
R836
C853
C854
C875
R844
JW859
FB802
CN801
JW835
D801
A A
R807
C809
C808
C807
Q808
R849
R850
R877
JW855
JW834
JW879
R827
R868
L807
R866
R852
R853
R854
JW857
D802
C867
R859
C838
R899
R811
R851
C840
JC807
R800
R808
C860
R858
C815
C814
C813
C812
R881 R879 R875
R880
R846
Q811
C127
C227
K
Q813
FB804
R876
R862
R892
R873
R872
R871
R870
R869
R831
C852
R864
FB803
JW311
JC805 R865
Q812
JW856
L806
JW818
C819
C818
C817
C816
R874
R828
C839
JW802
JW821
JW898
C811
R867
R888
R886
JC806
C820
Q823
C859
JC804
R496
JW895
JW894
FB801
C873
JW852
JW854
CN301
JW811
JW826
Q805
R497
JW801
R812
R499
R495
R498
JW845
JW846
JW896
Q822
Q821
JC802
CN901
Q824
1-866-321-
11
(11)
H
POWER
BOARD
CN905
(Page 21)
A
CD
BOARD
CN102
(Page 16)
E
CONTROL (1)
BOARD
CN403
(Page 24)
H/P BOARD
C219 CN303
L301
L201
C119
L101
SP201
(R-CH)
SP101
(L-CH)
JW303
R126
FB101
J322 J301
LINE IN
i
CN322
R226
FB201
FB301
1-866-324-
11
(11)
• Semiconductor
Location
Ref. No. Location
D301 F-3
D801 B-11
D802 B-12
D905 D-6
D906 D-5
D907 E-6
D908 D-10
D951 D-6
D953 C-7
IC301 I-3
IC304 C-3
IC801 I-10
IC802 F-8
IC803 G-10
IC804 M-8
IC901 C-10
Q101 G-4
Q121 F-4
Q201 G-4
Q221 F-4
Q801 G-10
Q802 G-9
Q803 J-8
Q804 J-8
Q805 I-12
Q806 J-7
Q807 L-12
Q808 L-11
Q809 M-4
Q810 M-4
Q811 L-11
Q812 L-12
Q813 M-11
Q821 E-13
Q822 E-13
Q823 C-12
Q824 D-13
Q951 D-5
Q952 C-5
Q953 D-5
Q954 C-7
Q955 C-6
Q956 D-10

ZS-SN10
5-9. PRINTED WIRING BOARDS – POWER SECTION – • See page 15 for Circuit Boards Location. :Uses unleaded solder.
A
B
C
D
E
F
G
H
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
BATTERY1 BOARD
JW906
BATTERY2 BOARD
JW905
DRY BATTERY
SIZE “D”
(IEC DESIGNATION R20)
6PCS. 9V
CN902
JW903 JW904
1-866-235-
CN904
1-866-236-
11
(11)
11
(11)
21
POWER BOARD
21
J901
~AC IN
CN905
H
MAIN
BOARD
CN901
(Page 20)
JW901
CN903
C908
C906
C901
C902
C904
D901
D902
D904
C903
D903
T901
POWER TRANSFORMER
F902
1-866-322-
ZS-SN10
11
(11)

22
22
ZS-SN10
ZS-SN10
5-10. SCHEMATIC DIAGRAM – MAIN SECTION (1/2) – • See page 26 for Waveforms. • See page 31 for IC Pin Function Description.
IC801
Q809
IC804
TP02
TP03
Q808
Q811
Q805
CN801
Q806
D801
CN804
Q822
FB801
FB802
FB803
FB804
C842
C421
C422
C831
C853
C862
C861
C833
C832
C806
C848
C849
C850
C852
C854
C841
C840
C838
C839
C868
C867
C820
C811
C819
C818
C817
C816
C815
C814
C813
C812
C809
C808
C807
C810
C869
C821
C822
C823
C824
C829
C830
C423
C424
C425
C426
C427
C428
C429
C430
C431
C432
C433
C434
C851
C802
C801
C875
C805
C860
C859
C845
C837
C803
C873
L801
L802
L803
L807
L806
X802
IC803
R892
Q810
Q803
Q812
Q807
CN805
IC802
Q802
Q801
Q804
S801
CN802
Q823
Q824
Q821
CN807
CN806
R825
R826
R847
R848
R856
R801
R803
R805
R829
R855
R830
R832
R833
R834
R835
R836
R837
R479
R478
R477
R476
R475
R474
R473
R472
R471
R470
R469
R468
R802
R806
R838
R839
R840
R841
R842
R851
R850
R849
R859
R862
R811
R899
R845
R846
R812
R813
R844
R863
R882
R884
R883
R886
R887
R888
R828
R864
R807 R808
R865
R868
R827
R831
R869
R870
R873
R874
R875
R876
R877
R878
R879
R880
R881
R894
R852
R866
R867
R891
R893
R896
R895
R853 R854
R817 R816
R495
R496
R497
R498
R499
R483
R484
R485
R486
R488
JC802
R872
R871
C870
C874
R480
R481
R815
C826
C825
C827
C828
C871
C872
C855
C856
D802
JC801
JC803
JC805
JC804
JC807
JC806
R818
X801
MB90483BPF-G
-153E1
RT1N144M
BR24L16
RT1N144M
RT1N151M-TP-1
RT1N144M
23P
RT1N144M
KDS121-RTK
4P
RT1N151M-TP-1
100p
100p
100p
1
100p
100p
100p
100p
100p
0.1
0.01
1000p
470p
100p
100p
0.01
0.01
0.01
0.01
0.01
1000p
0.01
100p
100p
100p
22p
22p
100p
100p
100p
100p
100p
100p
100p
100p
1
0.01
0.01
22p
10p
22p
10p
470p
470p
470p
470p
470p
470p
470p
470p
470p
470p
100p
470p
100p
0.01
0.1
220p
100p
22p
22p
47p
0.01
1000
10V
S-80828CNNB
220
RT1P144M
2SC4154TP
RT1P151M-TP-1
2SA1602TP
2P
XC6202-33
2SC4154TP
2SC4154TP
RT1P144M
11P
2SC4154TP
KTA1271-Y-AT
RT1P151M-TP-1
11P
11P
1k
1k
1k
1k
10k
10k
10k
10k
1k
10k
100
100
1k
1k
1k
1k
1k
4.7k
2.2k
2.2k
2.2k
4.7k
4.7k
4.7k
4.7k
4.7k
4.7k
4.7k
4.7k
10k
10k
1k
1k
2.2k
1k
1k
1k
1k
1k
0
1k
10k
10k
47k
10k
220k
220k
22k
10k
4.7k
4.7k
4.7k
220k
220k
220k
47k
47k
470 470
100k
1k
1k
220
1k
1k
220
220
1k
1k
1k
100
1k
1k
1k
4.7k
47k
10k
470k
1k
47k
10k
1k
10k 10k
4.7k 4.7k
4.7k
2.2k
100k
10
220
2.2k
2.2k
2.2k
2.2k
10k
0
1k
1k
10 50V
220
10V
1k
1k
4.7k
47p
220p
220p
47p
22p
22p
1
1
UDZSTE-175.1B
0
0
0
0
0
0
22k
4.19MHz
CD3.3V-ON
P-CON
A-MUTE
V-CLK
MEGA BASS
CD 3.3V
V-DATA
AU-6.0V
A-GND
CD-6.0V
MD-GND
AC-HI
BATT-COM
VDD(SW)
CD-L
CD-R
D-GND1
D-GND2
+B
R-VT
S-GND
BACKUP-ON
U-COM3.3V
TU-L
TU-R
VOL-CHK
KEY0
CLOK
DATA
XRST
XTACN
M-MUTE
ACK
REQ
XLAT2
CLOK2
ODATA2
IDATA2
IREQ
SCOR
XLAT
KEY2
KEY1
KEY0
KEY1
KEY2
DATA
CLOK2
M-MUTE
L-OUT
R-OUT
XTACN
XRST
IREQ
IDATA2
CLOK
XLAT2
REQ
ACK
XLAT
SCOR
ODATA2
L-OUT
R-OUT
SENS
SENS
R-CE
R-DATA
R-CLOCK
R-COUNT
R-MUTE
TU-L
RADIO 6V
TU-R
A-GND
R-VT
S-GND
D-GND2
VDD(SW)
KEY0
(1/2)
WAKE UP SWITCH
AC CHECK
DATA
D-OUT
DGND
L-OUT
AGND
R-OUT
XTACN
XRST
XLAT
SENS
SCOR
VDD
WP
SCL
SDA
GND
A2
A1
A0
VSS
X0
X1
VCC3
VSS
VCC5
AVRH
AVCC
AVSS
VSS
X0A
X1A
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
EEPROM-SEL
CLOK2
M-MUTE
IREQ
CLOK
XLAT2
REQ
ACK
MD-GND
CD-6.0V
DATA2
DVDD(3.3V)
AVDD(3.3V)
OPEN/CLOSE
CD LID
DETECT
SHIFT
RESET
NC
LOAD
VH-CONT
XRST
XTACN
M-MUTE
NC
REMOTE
ACK
REQ
XLAT2
CLOK2
ODATA2
IDATA2
IREQ
SCOR
XLAT
AC-IN
CD-DOOR
WP
MD2
MD1
MD0
P81
P80
VM
VH
VOL-CHECK
3.3V-CHECK
KEY0
KEY2
KEY1
NC
NC
VM-CONT
R-MUTE
R-CE
R-CLOCK
R-DATA
R-COUNT
BACKUP-ON
CD3.3V-ON
TU-ON
P-CON
A-MUTE
CLOK
DATA
SENS
TESTB
TESTA
MEGABASS
SHIMUKE3
SHIMUKE2
SHIMUKE1
VOL-CLK
VOL-DATA
EEP-SDA
EEP-SCL
LCD-DB0
LCD-DB1
LCD-DB2
LCD-DB3
LCD-DB4
LCD-DB5
LCD-DB6
LCD-DB7
LCD-RES
LCD-RW
LCD-E
LCD-RS
SYSTEM CONTROLLER
JOG-A
JOG-B
BL
Q821,822
DC LEVEL DETECT
1
1
Q823,824
LOAD CONTROL
SWITCH
RESET SIGNAL
GENERATOR
NC
GND
RST
VCC
Q801,802
SHIFT CLOCK
32.768kHz
LCD-DB0
BL 6V
LCD-DB1
LCD-DB2
LCD-DB3
LCD-DB4
LCD-DB5
LCD-DB6
LCD-DB7
LCD-E
LCD-RW
LCD-RS
LCD-RES
LCD-3.3V
D-GND
REMOTE
JOG-A
JOG-B
KEY2
BL-CONT
KEY1
RMC-VCC
+3.3V REGULATOR
Q804,806
B+ SWITCH
GND
OUT
IN
LED
DRIVE
(TW,KR,AUS)
MUTING
Q809,810
B+ SWITCH
Q811,812
DC LEVEL DETECT
EEPROM
(SP,TW,KR,TH,AUS)
EXCEPT
TW,KR,AUS
(US,CND,E,MX)
47 6.3V(US,CND,E,MX)
47 10V(SP,TW,KR,TH,AUS)
47µH
0.22µH
10µH
1µH
Ver. 1.3

ZS-SN10
5-11. SCHEMATIC DIAGRAM – MAIN SECTION (2/2) – • See page 27 for IC Block Diagrams.
CD-L
CD-R
TU-L
TU-R
CD-6.0V
R-VT
MD-GND
D-GND1
VOL-CHK
A-GND
MEGA BASS
V-DATA
V-CLK
CD 3.3V
A-MUTE
P-CON
AC-HI
BATT-COM
CD3.3V-ON
VDD(SW)
+B
AU-6.0V
D-GND2
S-GND
U-COM3.3V
BACKUP-ON
R103
2.2k
R104
1k
10k
R101
2.2 50V
C101
10k
R201
2.2 50V
C201
2.2 50V
C102
R204
1k
R203
2.2k
2.2 50V
C202
R105 R205
10k 10k
INPUT SELECT,
ELECTRICAL
VOLUME,
SURROUND/
TONE
CONTROL
IC301
BD3870FS
D907
1SS355TE-17
R326
1k
C303
0.47
50V
C326
220
16V
R IN
CAP
C208 2200p
R325
1k
C117 1 50V
C217 1 50V
C118 1 50V
C218 1 50V
C204 4.7 50V
C104
4.7 50V
L IN
(2/2)
TNFR
C108 2200p
R305 1k
R306 1k
Q813
2SA1602TP
R858
47k
SEL R
TNFL
C109 0.1
B+ SWITCH
SEL L
BNFL
R113 R213
470k 470k
C110 0.1
R112
4.7k
R321 2.2k
R800
470k
CD-R
BOL
C209 0.1
CD-L
BNFR
C210 0.1
R212
4.7k
220 16V
C959
RA-R
BOR
0.1
C958
C203
0.47
50V
RA-L
RCH
C301
100
10V
LI-R
LCH
C302 0.01
Q956
2SB798
+3.3V REGULATOR
LI-L
VCC
C103
0.47
50V
C105 1000p
C205 1000p
C106 1000p
C206 1000p
FILTER
SI
C304
47
10V
GND
SC
C107 1000p
C207 1000p
+3.3V REGULATOR
IC901
S-816A33AMC
C306
100p
C305
100p
R304
10k
R110 R111
10k 1k
R210 R211
10k 1k
C111
4.7
50V
R301
100
R302
100
R303
10k
Q955
KTC3203-Y
R309
10k
L804
47µH
C211
4.7
50V
+6V REGULATOR
R900
1k
D908
ISS355-TE
EXT
OUT
GND
IN
ON/OFF
C963 10 50V
0.1
C957
R106
47k
R206
47k
D301
KDS121-RTK
R202
2.2k
R324
R116
220
R114
2.2k
R119 4.7k
R219
4.7k
R214 R215 MEGA BASS CONTROL
2.2k 1k
R216
220
100 10V
C956
100 10V
C954
C325
10
50V
0.01
UDZSTE-6.8B
C907
1M
D905
2.2k
R102
Q101,201
220 10V
C955
0.01
C961
C960
R903
R902
R115
1k
Q101
2SC4154TP
C216
2200p
0.01
1k
1k
C116
2200p
Q954
2SD2394-F
Q201
2SC4154TP
C213
0.0022
C212
0.0047
+6V REGULATOR
C952 0.01
D953 UDZSTE-176.8B
C953 220 10V
1k
R901
C113 0.0022
C112 0.0047
Q121,221
C951
0.01
MUTING
1k
R961
R118
0
R117
470
R220 47k R120 47k
C214 1 50V C114 1 50V
R217
470
R218
0
1k
R960
1k
R959
4.7k
R121
23
R221 4.7k
Q121 Q221
DTC143TUA DTC143TUA
R127 R227
0 0
JC808
0
D906
ISS355TE-17
Q953
2SC4154TP
R958
2.2k
R123 R122 C120
470 220 100p
C321
22
25V
Q952
KTA1273Y
PREGND2
R956
47k
R957
2.2k
R954
10k
R955
10k
PREGND1
D951
KDS120-RTK
23
Q951
RT1N436M-TP-1
R953
C220
R222
100p
220
R223
470
C223 C322
C123
47
C122 C222 47 47
1000p 1000p 10V 10V
10V
2.2k
2.2k
R952
Q951-953
B+ SWITCH
2.2k
R951
2.2k
R950
POWER AMP
IC304
BA5417
FILTER STBY
POWER
GND
C224
100 10V
C225 C125
0.1 0.1
R322 R224 R124
1k 2.2 2.2
C950
4700
16V
BSR
VCC
BS L
C126
C124
1000
100
10V
10V
C226
1000
10V
NC
R225
4.7k
C127
100p
R323
10k
4.7k
R125
C227
100p
CN302
3P
LINE-L
A-GND
LINE-R
C324
0.22
CN301 CN322
4P 4P
CN901
4P
VDD
GND
AC-HI
BATT-COM
CN303
3P
LINE-L
A-GND
LINE-R
J901
CN904
2P
C119
1000p
C219
1000p
CN905
4P
VDD
GND
AC-HI
BATT-COM
L101 47µH
L301 1µH
L201 47µH
T901
R226 100
R126 100
POWER TRNASFORMER
FB201
FB101
FB301
CN323
4P
L
GND
R
GND
F902
T2AL 250V(SP,KR,TH,AUS)
2.5A 125V(US,CND,E,MX,TW)
DRY BATTERY
SIZE"C"
(IEC DESIGNATION R14)
6PCS. 9V
C906
10 C908
50V 0.22
SP101
(L-CH)
SP201
(R-CH)
C901 0.022
D901 1N4002B
D902 1N4002B
C902 0.022
C903 0.022
D903 1N4002B
D904 1N4002B
C904 0.022
J322
LINE IN
J301
ZS-SN10
CN903
3P
BATT-COM
GND
BATT
BATT-COM
BATT-COM
GND
BATT
CN902
4P
Ver. 1.3

ZS-SN10
5-12. PRINTED WIRING BOARDS – PANEL SECTION – • See page 15 for Circuit Boards Location. :Uses unleaded solder.
A
B
C
D
E
F
G
H
I
J
ZS-SN10
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
S413
/ TUNE
+
LCD BOARD
CONTROL (1)
D401
OPR/BATT
R425
R421
R419
S425
R440
R439
SEARCH
R420
S402
POWER
R418
R494
R493
S414
ENTER/
MEMORY
R438
S412
/ TUNE
–
R426 R427
3
1
S401
ROTARY
ENCODER
(JOG)
R402
S403
SLEEP
REPEAT MODE
S422
R401
C420
C419
R453 R454
CN401
CN403
S423
22
R490
R452
C401
C402
R492
CN405
24
R451
R491
L401
R417
C418
C403
DISPLAY
C404
S424
C417
24
R450
LCD401
LIQUID CRYSTAL DISPLAY
C413
C414
L402
C411
C412
CN402
C410
C409
C408
L403
MAIN BOARD
CN807 C MAIN BOARD
CN806
(Page 20) (Page 20)
1-866-327-
11
(11)
E
MAIN BOARD
CN804
(Page 20)
D
CONTROL (2)
CN404
C407
1
JW402
LINE
S410
R416
C405
C406
S407 S406
R432 R431
S411
R415
3
RADIO/BAND
AUTO PRESET
SOUND MEGA BASS
1
R437
R430
D402
(LCD BACK LIGHT)
R436
R458
R459
S418
>
.
S420 PRESET
+
JW403
PRESET
–
S421
IC401
S405
S402 – 407,
S410 – 414,
S418 – 424
R447
R446
R448
u
S419
x
R449
S404
R429
– VOLUME
+
R428
1-866-323-
1-867-694-
11
(11)
11
(11)

ZS-SN10
5-13. SCHEMATIC DIAGRAM – PANEL SECTION –
(Page 22)
(Page 22)
CN405
11P
CN402
11P
S401
ROTARY ENCODER(JOG)
R401
1k
C420
0.01
A
R402
1k
B GND
C419
0.01
S410
RADIO/BAND
AUTO
PRESET
R446
220
R447
470
R436
220
S411
LINE
R448
1k
R437
470
L401
47µH
L403
1µH
R458
470
R417
C407
R438 R439
1k 1k
R449
1k
S418 S419 S420 S421
PRESET +
470k
L402
R459
*
47p
47p
C408
47p
C409
47p
C410
R450
2.2k
S422
REPEAT
47p
C411
47p
C412
47p
C413
C414
C417
R451
2.2k
R440
2.2k
S423
MODE
C418
R452
1k
25
C404
C403
IC401
RPM7140
C405
470p
C402
R493
1k
S412 S413 S414 S425
/TUNE
–
PRESET –
1µH
*R459
220 (WHITE:US,CND)
470 (EXCEPT WHITE:US,CND)
D402
*
*D402
SLI-343YC3F (EXCEPT WHITE:US,CND)
SLR343EBT (WHITE:US,CND)
(LCD BACK LIGHT)
/TUNE
+
47p
47p
ENTER/
MEMORY
47p
1
1
1
R453
2.2k
R492
10k
R490
2.2k
R491
0
R415
47k
R416
100k
SEARCH
S424
DISPLAY
R494
2.2k
R454
4.7k
25
C401
1
C406
0.01
LCD401
(Page 22)
SW 9V
KEY0
D-GND2
D-GND2
CN403
4P
CN404
2P
KEY0
D-GND2
S402
S403
POWER SLEEP
R428
1k
S404
VOLUME
+
R426
220
R429
1k
S405
R427
470
VOLUME
–
D401
L-34HD
OPR/BATT
R418
470
R419
470
R430
2.2k
S406
MEGA BASS
R420
1k
R421
1k
R425
220
R431
1k
S407
SOUND
ZS-SN10
KEY0
D-GND2
R432
2.2k
Ver. 1.3
CN401
2P

ZS-SN10
Ver. 1.3
• Waveforms
– CD Board –
1
2
3
4
IC201 1 (LRCK)
(CD PLAY mode)
IC201 u; (RFACO)
(CD PLAY mode)
ZS-SN10
22.8 µs
1 V/DIV, 10 µs/DIV
IC201 5 (BCK)
(CD PLAY mode)
472 ns
1 V/DIV, 200 ns/DIV
0.5 to 1.1 Vp-p
200 mV/DIV, 500 ns/DIV
IC201

– MAIN Board –
IC301 BD3870FS-E2
IC901 S-816A33AMC-BAI-T2-G
SOURCE
POWER
SUPPLY
1
EXT
VOUT
5
REFERENCE
VOLTAGE
ERROR
AMP
2
VSS
SINK
DRIVER
OVERCURRENT
PROTECT
CIRCUIT
3
ON/OFF
VIN
4
ZS-SN10
27

ZS-SN10
• IC Pin Function Description
CD BOARD IC201 CXD3014-201R (CD DSP)
Pin No. Pin Name I/O Description
28
1 LRCK O L/R sampling clock signal output terminal
2 LRCKI I L/R sampling clock signal input terminal
3 PCMD O Serial data output terminal
4 PCMDI I Serial data input terminal
5 BCK O Bit clock signal output terminal
6 BCKI I Bit clock signal input terminal
7 XTACN I
Oscillation circuit on/off switch control signal input from the system controller
“H”: self-oscillation, “L”: oscillation stop
8 XRST I Reset signal input from the system controller “L”: reset
9 VSS — Ground terminal
10 IREQ I Codec data request signal input from the system controller
11 CLOK I CD serial data transfer clock signal input from the system controller
12 DATA2 I/O Codec serial data input/output with the system controller
13 XLAT2 I Codec serial data latch pulse input from the system controller
14 REQ I Codec chip select signal input from the system controller
15 ACK I Codec acknowledge signal input from the system controller
16 XLAT I CD serial data latch pulse input from the system controller
17 VDD — Power supply terminal (+2.5V)
18 SVSS — Ground terminal
19 SVDD — Power supply terminal (+2.5V)
20 SENS O SENS signal output to the system controller
21 WFCK — Not used
22 XUGF — Not used
23 XPCK — Not used
24 GFS — Not used
25 C2PO — Not used
26 SCOR O Subcode sync (S0+S1) detection signal output to the system controller
27 VDD — Power supply terminal (+2.5V)
28 COUT — Not used
29 SVSS — Ground terminal
30 SVDD — Power supply terminal (+2.5V)
31 MIRR — Not used
32 DFCT — Not used
33 FOK — Not used
34 VSS — Ground terminal
35 VDD — Power supply terminal (+2.5V)
36 VSS — Ground terminal
37 MIRR — Not used
38 MDP O Spindle motor servo control signal output terminal
39 SSTP I Disc inner position detection signal input terminal
40 IOVSS1 — Ground terminal
41 SFDR O Sled servo drive signal (+) output to the coil/motor drive
42 SRDR O Sled servo drive signal (–) output to the coil/motor drive
43 TFDR O Tracking servo drive signal (+) output to the coil/motor drive
44 TRDR O Tracking servo drive signal (–) output to the coil/motor drive
45 FFDR O Focus setvo drive signal (+) output to the coil/motor drive
46 FRDR O Focus servo drive signal (–) output to the coil/motor drive

Pin No. Pin Name I/O Description
47 IOVDD1 — Power supply terminal (+3.3V)
48 AVDD0 — Power supply terminal (+3.3V)
49 AVSS0 — Ground terminal
50 E I E signal input from the optical pick-up block
51 F I F signal input from the optical pick-up block
52 TEI I Tracking error signal input terminal
53 TEO O Tracking error signal output terminal
54 FEI I Focus error signal input terminal
55 FEO O Focus error signal output terminal
56 VC O Middle point voltage output terminal
57 A I A signal iuput from the optical pick-up block
58 B I B signal input from the optical pick-up block
59 C I C signal iuput from the optical pick-up block
60 D I D signal input from the optical pick-up block
61 AVDD4 — Power supply terminal (+3.3V)
62 RFDCO O Not used
63 PDSENS I Not used
64 AC_SUM O RFAC summing amplifier signal output terminal
65 EQ_IN I RF equalizer circuit input terminal
66 LD O
Laser diode on/off control signal output to the automatic power control circuit
“L”: laser off, “H”: laser on
67 PD I Light amount monitor input from the optical pick-up block laser diode
68 RFC I Equalizer cut off frequency adjustment terminal
69 AVSS4 — Ground terminal
70 RFACO O EFM signal output terminal
71 RFACI I EFM signal input terminal
72 AVDD3 — Power supply terminal (+3.3V)
73 BIAS I Asymmetry circuit constant current input terminal
74 ASYI I Playback EFM asymmetry comparator voltage input terminal
75 ASYO O Playback EFM full-swing output terminal
76 VPCO O Charge pump output terminal for broad-band EFM PLL
77 VCTL I VCO2 control voltage input terminal for broad-band EFM PLL
78 AVSS3 — Ground terminal
79 CLTV I VCO1 control voltage input terminal for multiplier
80 FILO O Filter output terminal for master PLL
81 FILI I Filter input terminal for master PLL
82 PCO O Charge pump output terminal for master PLL
83 SVSS — Ground terminal
84 SVDD — Power supply terminal (+2.5V)
85 SRAMSTB I Codec standby on/off control signal input terminal Not used
86 VDD — Power supply terminal (+2.5V)
87 VSS — Ground terminal
88 TEST1 I For test terminal Normally fixed at “L”
89 DATA I CD serial data input from the system controller
90 CLOK2 I Codec serial data transfer clock signal input from the system controller
91 SVSS — Ground terminal
92 SVDD — Power supply terminal (+2.5V)
93 JTAGTCK — Not used
94 JTAGTDI — Not used
ZS-SN10
29

ZS-SN10
Pin No. Pin Name I/O Description
30
95 JTAGTDO — Not used
96 JTAGTMS — Not used
97 TRST — Not used
98 VSS — Ground terminal
99 VDD — Power supply terminal (+2.5V)
100 IOVDD2 — Power supply terminal (+3.3V)
101 DOUT O Digital audio signal output terminal Not used
102 TEST I For test terminal Normally fixed at “L”
103 TES1 I For test terminal Normally fixed at “L”
104 IOVSS2 — Ground terminal
105 PLLVDD — Power supply terminal (+2.5V)
106 PLLVSS — Ground terminal
107 XVSS — Ground terminal
108 XTAO O System clock output terminal (16.9344 MHz)
109 XTAI I System clock input terminal (16.9344 MHz)
110 XVDD — Power supply terminal (+2.5V)
111 AVDD1 — Power supply terminal (+3.3V)
112 AOUT1 O L-ch analog audio signal output terminal
113 VREFL O L-ch reference voltage output terminal
114 AVSS1 — Ground terminal
115 AVSS2 — Ground terminal
116 VREFR O R-ch reference voltage output terminal
117 AOUT2 O R-ch analog audio signal output terminal
118 AVDD1 — Power supply terminal (+3.3V)
119 IOVDD0 — Power supply terminal (+3.3V)
120 IOVSS0 — Ground terminal

MAIN BOARD IC801 MB90483BPF-G-153E1 (SYSTEM CONTROLLER)
Pin No. Pin Name I/O Description
1 to 6 NC — Not used
7 EEP-SCL O Serial clock signal output terminal to the EEPROM
8 EEP-SDA I/O Two-way serial data bus with the EEPROM
9 VOL-DATA O Serial data output to the electrical volume
10 VOL-CLK O Serial data transfer clock signal output to the electrical volume
11 VSS — Ground terminal
12 to 14 SIMUKE1 to SIMUKE3 I For destination setting terminal
15 MEGABASS O MEGABASS on/off control signal output terminal
16 TESTA I For CD test setting terminal Fixed at “H” in this set
17 TESTB I For LCD test setting terminal Fixed at “H” in this set
18 SENS I Internal status (SENSE) signal input from the CD DSP
19 DATA O Serial data output to the CD DSP
20 CLOK O Serial data transfer clock signal output to the CD DSP
21 A-MUTE O Audio muting on/off control signal output terminal “H”: muting
22 P-CON O Power control signal output terminal “H”: active
23 VCC5 — Power supply terminal (+3.3V)
24 TU-ON O Tuner power on/off control signal output terminal “H”: tuner on
25 CD3.3V-ON O CD power on/off control signal output terminal “H: CD on
26 BACKUP-ON O CD power select signal output terminal for power off state “L”: power off state
27 R-COUNT I PLL serial count data input terminal
28 R-DATA O PLL serial data output terminal
29 R-CLOCK O PLL serial data transfer clock signal output terminal
30 R-CE O PLL chip enable signal output terminal
31 R-MUTE O Tuner muting on/off control signal output terminal “H”: active
32 VM-CONT O Battery middle voltage (+4.5V) detection circuit control signal output terminal
33, 34 NC O Not used
35 AVCC — Power supply terminal (+3.3V) (for A/D converter)
36 AVRH I Reference voltage input terminal (+3.3V) (for A/D converter)
37 AVSS — Ground terminal (for A/D converter)
38 NC O Not used
39 KEY1 I Key input terminal (A/D input)
40 KEY2 I Key input terminal (A/D input)
41 KEY0 I Key input terminal (A/D input)
42 VSS — Ground terminal
43 3.3V-CHECK I CD power voltage detection signal input terminal
44 VOL-CHECK I Electrical volume power voltage detection signal input terminal
45 VH I Battery high voltage (+9V) detection signal input terminal
46 VM I Battery middle voltage (+4.5V) detection signal input terminal
47, 48 P80, P81 I Not used
49 to 51 MD0 to MD2 I For mode setting terminal
52 WP I Key interruption processing start signal input terminal
53 CD DOOR I CD lid open/close detection switch input terminal “L”: CD lid is close
54 AC-IN I AC voltage detection signal input terminal “L”: AC in
55 XLAT O Serial data latch pulse output to the CD DSP
56 SCOR I Subcode sync (S0+S1) detection signal input from the CD DSP
57 IREQ I Codec data request signal input from the CD DSP
58 IDATA2 I Codec serial data input from the CD DSP
59 ODATA2 O Codec serial data output to the CD DSP
ZS-SN10
Ver. 1.3
31

ZS-SN10
Pin No. Pin Name I/O Description
32
60 CLOK2 O Codec serial data transfer clock signal output to the CD DSP
61 XLAT2 O Codec serial data latch pulse output to the CD DSP
62 REQ O Codec data request signal output to the CD DSP
63 ACK I Codec acknowledge signal input from the CD DSP
64 REMOTE I Remote control signal input terminal
65 NC O Not used
66 M-MUTE O Muting on/off control signal output to the coil/motor drive “H”: active
67 XTACN O
Oscillation circuit on/off switch control signal output to the CD DSP
“H”: self-oscillation, “L”: oscillation stop
68 XRST O System reset signal output to the CD DSP “L”: reset
69 VH-CONT O Battery high voltage (+9V) detection circuit control signal output terminal
70 LOAD O Load control signal output for battery check state
71 to 76 NC O Not used
77 RESET I System reset signal input from the reset signal generator “L”: reset
78 SHIFT O Shift point terminal for oscillation frequency change
79 X1A O Sub system clock output terminal (32.768 kHz)
80 X0A I Sub system clock input terminal (32.768 kHz)
81 VSS — Ground terminal
82 X0 I Main system clock input terminal (4.19 MHz)
83 X1 O Main system clock output terminal (4.19 MHz)
84 VCC3 — Power supply terminal (+3.3V)
85 to 92 LCD-DB0 to LCD-DB7 I/O LCD parallel data input/output terminal
93 LCD-RES O LCD reset control signal output terminal “L”: reset
94 LCD-RW O LCD chip data read/write signal output terminal
95 LCD-E O LCD data enable signal output terminal
96 LCD-RS O LCD resistor select signal output terminal
97 EEPROM-SEL I EEPROM setting terminal Fixed at “L” in this set
98, 99 JOG-A, JOG-B I Jog dial pulse input from the rotary encoder (JOG)
100 BL O LCD back light on/off control signal output terminal “H”: back light on

NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Accessories are given in the last of electrical
parts list.
6-1. CABINET SECTION
3
cabinet top section
SECTION 6
EXPLODED VIEWS
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
R R
Parts of Color Cabinet’s Color
• Abbreviation
AUS : Australian model
CND : Canadian model
KR : Korean model
MX : Mexican model
SP : Singapore model
TH : Thai model
TW : Taiwan model
6
ZS-SN10
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 2-582-114-01 LID, BATTERY (BLACK)
1 2-582-114-11 LID, BATTERY (WHITE)
1 2-582-114-21 LID, BATTERY (SILVER)
2 3-040-916-01 FOOT (FRONT), RUBBER
3 3-254-144-01 SCREW (B3), (+) BV TAPPING
(for WHITE, SILVER)
3 3-254-144-11 SCREW (B3), (+) BV TAPPING (for BLACK)
4 3-252-833-01 SCREW (M3), (+) P
5 2-582-130-01 WINDOW, LCD (for BLACK, WHITE)
5 2-582-130-21 WINDOW, LCD (for SILVER)
6 1-831-915-11 CABLE, FLEXIBLE FLAT (4 CORE)
7 3-252-827-01 SCREW (B2.6), (+) BV TAPPING
3
ANT1
10
cabinet front section
4
3
cabinet bottom
section
9
11
13
5
14
3
9
12
8 A-1105-346-A MAIN BOARD, COMPLETE (US, CND, E, MX)
8 A-1105-348-A MAIN BOARD, COMPLETE (SP, TH)
8 A-1105-349-A MAIN BOARD, COMPLETE (TW, KR, AUS)
9 2-024-906-01 CUSHION (REAR)
13
10 3-018-963-01 CUSHION (BATTERY CASE LID)
11 3-577-414-01 SPACER (for BLACK)
11 3-577-414-11 SPACER (for WHITE, SILVER)
12 2-594-013-01 PLATE (MAIN), SHIELD
13 3-254-144-01 SCREW (B3), (+) BV TAPPING
14 4-017-441-01 CUSHION (B) (for BLACK)
14 4-017-441-31 CUSHION (B) (for WHITE, SILVER)
ANT1 1-754-241-11 ANTENNA, TELESCOPIC
7
1
8
MAIN board
2
not
supplied
Ver. 1.4
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant le
numéro spécifié.
13
33

ZS-SN10
Ver. 1.4
6-2. CABINET FRONT SECTION
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
34
71
(for SILVER)
72
not
supplied
70
53
73
69
70
68
70
68
66
55
54
57
LCD401
59
60
not
supplied
51 2-582-140-01 BOX (R), SPEAKER
52 X-2050-833-1 CABI (FRONT) SUB ASSY (BLACK) (US)
52 X-2050-834-1 CABI (FRONT) SUB ASSY (WHITE) (US)
52 X-2050-835-1 CABI (FRONT) SUB ASSY (BLACK) (CND)
52 X-2050-836-1 CABI (FRONT) SUB ASSY (WHITE) (CND)
56
SP101
52 X-2050-837-1 CABI (FRONT) SUB ASSY (SILVER)
(EXCEPT US)
52 X-2109-390-1 CABINET (FRONT) SUB ASSY (SILVER) (US)
53 2-582-115-01 BUTTON (CD) (BLACK)
53 2-582-115-11 BUTTON (CD) (WHITE)
53 2-582-115-21 BUTTON (CD) (SILVER)
54 3-254-151-01 SCREW (B2.6), (+) P TAPPING
55 3-254-143-01 SCREW (B3), (+) BV TAPPING
56 2-582-139-01 BOX (L), SPEAKER
57 A-1105-337-A LCD BOARD, COMPLETE (for BLACK, SILVER)
57 A-1124-479-A LCD BOARD, COMPLETE (for WHITE)
58 2-582-131-01 HOLDER (LCD)
59 2-582-138-03 PLATE, LIGHT GUIDE
60 2-582-152-01 ILLUMINATOR
61 3-252-827-01 SCREW (B2.6), (+) BV TAPPING
62 2-582-133-01 HOLDER (JOG)
52
68
IC401
not
supplied
69
66
58
64
55
54
LCD board
65
63 62
64
not
supplied
SP201
66
66
51
61
54
66
67
66
63 2-582-127-01 KNOB (JOG) (BLACK)
63 2-582-127-11 KNOB (JOG) (WHITE)
63 2-582-127-21 KNOB (JOG) (SILVER)
64 1-831-926-11 CABLE, FLEXIBLE FLAT (11 CORE)
65 3-254-144-01 SCREW (B3), (+) BV TAPPING
66 2-024-906-01 CUSHION (REAR)
67 2-633-236-01 CUSHION (TUNER FFC)
68 3-357-572-01 CUSHION
69 3-885-228-01 CUSHION (B)
70 4-942-511-01 SPACER
71 X-2059-969-1 PANEL SUB ASSY (for BLACK)
71 X-2059-970-1 PANEL SUB ASSY (for WHITE)
71 2-582-132-01 PANEL (for SILVER)
72 2-582-150-01 SHEET (LCD WINDOW), ADHESIVE
(for SILVER)
73 2-178-844-01 WASHER (CD CHASSIS)
IC401 6-701-681-01 IC RPM7140-V4
LCD401 1-479-194-11 ELEMENT UNIT, LIQUID CRYSTAL
SP101 1-826-212-11 SPEAKER (10cm) (L-ch)
SP201 1-826-212-11 SPEAKER (10cm) (R-ch)
65

6-3. CABINET TOP SECTION-1
108
cabinet top section-2
116
107
104
103
106
115
not
supplied
ZS-SN10
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 2-582-129-01 HANDLE (R), HOLDER (BLACK)
101 2-582-129-11 HANDLE (R), HOLDER (WHITE)
101 2-582-129-21 HANDLE (R), HOLDER (SILVER)
102 3-047-468-11 DAMPER
103 3-252-827-01 SCREW (B2.6), (+) BV TAPPING
104 2-582-128-01 HANDLE (L), HOLDER (BLACK)
104 2-582-128-11 HANDLE (L), HOLDER (WHITE)
104 2-582-128-21 HANDLE (L), HOLDER (SILVER)
105 1-452-899-11 MAGNET
106 2-582-110-11 LID, CD (SILVER)
106 2-582-110-21 LID, CD (BLACK)
106 2-582-110-31 LID, CD (WHITE)
107 3-254-151-01 SCREW (B2.6), (+) P TAPPING
108 2-591-496-01 COVER (HANDLE) (BLACK)
108 2-591-496-11 COVER (HANDLE) (WHITE)
114
113
102
103
111
110
109
105
112
103
116
113
101
108 2-591-496-21 COVER (HANDLE) (SILVER)
109 2-582-113-01 HANDLE (BLACK)
109 2-582-113-11 HANDLE (WHITE)
109 2-582-113-21 HANDLE (SILVER)
110 3-019-395-01 PLATE, CHUCKING
111 3-253-143-01 SCREW (B2.6), (+) P TAPPING
112 2-582-142-02 SPRING (CD)
113 2-592-833-01 CUSHION
114 2-634-609-01 COVER (SCREW) (for BLACK)
114 2-634-609-11 COVER (SCREW) (for WHITE)
114 2-634-609-21 COVER (SCREW) (for SILVER)
115 4-942-511-01 SPACER
116 4-942-511-01 SPACER (BLACK)
116 4-942-511-11 SPACER (WHITE, SILVER)
35

ZS-SN10
Ver. 1.4
6-4. CABINET TOP SECTION-2
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
36
154
153
155
168
167
152
151
S801
151
151 3-252-827-01 SCREW (B2.6), (+) BV TAPP
152 A-1105-376-A CONTROL (2) BOARD, COMPLETE
153 A-1105-375-A CONTROL (1) BOARD, COMPLETE
154 2-582-134-01 HOLDER (LED)
155 X-2050-819-1 CABINET TOP SUB ASSY (BLACK) (US)
not supplied
168
155 X-2050-820-1 CABINET TOP SUB ASSY (WHITE) (US)
155 X-2050-821-1 CABINET TOP SUB ASSY (BLACK) (CND)
155 X-2050-822-1 CABINET TOP SUB ASSY (WHITE) (CND)
155 X-2050-823-1 CABINET TOP SUB ASSY (SILVER)
(EXCEPT US)
155 X-2109-392-1 CABINET (UPPER) SUB ASSY (SILVER) (US)
156 3-923-736-01 COVER, CD
157 3-931-379-21 RUBBER, VIBRATION PROOF (RED)
158 3-931-379-31 RUBBER, VIBRATION PROOF (GREEN)
164
166
165
157
159
163
157
162
156
optical pick-up section
161
158
158
159
160
S201
159 3-252-828-01 SCREW (B2.6), (+) PWH TAPPING
160 1-828-377-51 WIRE (FLAT TYPE) (23 CORE)
161 A-1107-453-A CD BOARD, COMPLETE
162 3-245-709-51 SCREW
163 1-832-404-21 WIRE (FLAT TYPE) (16 CORE)
164 3-015-345-21 CUSHION
165 3-255-320-01 CUSHION, CR
166 3-018-963-01 CUSHION (BATTERY CASE LID)
167 3-357-572-01 CUSHION
168 3-885-228-01 CUSHION (B)
S201 1-771-853-11 SWITCH, DETECTION (LIMIT)
S801 1-692-960-21 SWITCH, PUSH (1 KEY)
(CD LID OPEN/CLOSE DETECT)

6-5. CABINET BOTTOM SECTION
214
206
T901
205
not
supplied
215
215
F902
214
204 203
* 201 1-866-326-11 BATTERY2 BOARD
202 3-240-561-02 TERMINAL (–), BATTERY
* 203 1-866-325-11 BATTERY1 BOARD
204 A-1105-328-A H/P BOARD, COMPLETE
205 3-252-827-01 SCREW (B2.6), (+) BV TAPPING
J901
213
215
202
206 3-254-143-01 SCREW (B3), (+) BV TAPPING
207 A-1105-360-A POWER BOARD, COMPLETE
208 1-827-720-51 WIRE (FLAT TYPE) (11 CORE)
209 A-1105-354-A TUNER BOARD, COMPLETE (US, CND, E, MX)
209 A-1105-355-A TUNER BOARD, COMPLETE
(SP, TW, KR, TH, AUS)
210 2-582-141-01 TERMINAL, ANTENNA
211 2-582-153-01 SHEET, BATTERY
212 2-582-109-02 CABINET (BOTTOM) (BLACK) (US)
212 2-582-109-12 CABINET (BOTTOM) (WHITE) (US)
212 2-582-109-22 CABINET (BOTTOM) (BLACK) (CND)
212 2-582-109-32 CABINET (BOTTOM) (WHITE) (CND)
212 2-582-109-42 CABINET (BOTTOM) (SILVER)
(EXCEPT US, CND)
207
not
supplied
202
216
not
supplied
208
201
213
L3
212
211
209
TUNER board
214
210
not
supplied
not
supplied
212 2-582-109-62 CABINET (BOTTOM) (SILVER) (US)
212 2-582-109-72 CABINET (BOTTOM) (SILVER) (CND)
213 3-252-830-01 SCREW (B3), (+) PWH TAPPING
ZS-SN10
Ver. 1.4
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
214 3-018-963-01 CUSHION (BATTERY CASE LID)
215 3-357-572-01 CUSHION
216 4-942-511-01 SPACER (for BLACK)
216 4-942-511-11 SPACER (for WHITE, SILVER)
0 F902 1-533-450-12 FUSE, GLASS TUBE (DIA. 5) (2.5A/125V)
(US, CND, E, MX, TW)
0 F902 1-533-468-12 FUSE, GLASS TUBE (DIA. 5) (T2AL/250V)
(SP, KR, TH, AUS)
0 J901 1-526-818-11 INLET, AC (E, MX)
0 J901 1-526-838-11 INLET, AC 2P (SP, TW, KR, TH, AUS)
0 J901 1-540-009-11 INLET, AC (US, CND)
L3 1-754-117-12 ANTENNA, FERRITE-ROD (MW)
0 T901 1-435-917-22 TRANSFORMER, POWER (US, CND, E, MX, TW)
0 T901 1-435-918-22 TRANSFORMER, POWER (SP, KR, TH, AUS)
37

ZS-SN10
6-6. OPTICAL PICK-UP SECTION (KSM-213CDP)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
38
505
501
not supplied
(M401 (SPINDLE))
M402
0501 8-848-483-12 OPTICAL PICK-UP (KSS-213C/C2RP1)
502 2-174-500-01 SCREW (2X3)
503 2-626-908-01 SHAFT, SLED
504 2-627-003-01 GEAR (B) (RP)
505 X-2162-709-2 CHASSIS ASSY (CDP), MOTOR
(including M401 (SPINDLE))
506
not supplied
504
502
503
506 2-626-907-11 GEAR (A)
M402 X-2625-769-1 GEAR ASSY (MB) (RP), MOTOR (SLED)

NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
• CAPACITORS
uF: µF
• COILS
uH: µH
SECTION 7
ELECTRICAL PARTS LIST
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. ., uPA. . : µPA. .,
uPB. . : µPB. ., uPC. . : µPC. .,
uPD. . : µPD. .
• Abbreviation
AUS : Australian model.
CND : Canadian model.
KR : Korean model.
MX : Mexican model.
ZS-SN10
When indicating parts by reference number,
please include the board name.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 1-866-325-11 BATTERY1 BOARD
***************
3-240-561-02 TERMINAL (–), BATTERY
************************************************************
* 1-866-326-11 BATTERY2 BOARD
***************
3-240-561-02 TERMINAL (–), BATTERY
< CONNECTOR >
CN904 1-815-550-11 PIN, CONNECTOR (PWB) 2P
************************************************************
A-1107-453-A CD BOARD, COMPLETE
*******************
< CAPACITOR >
C101 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C102 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C103 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C104 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C105 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C107 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C108 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C109 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C110 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C111 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C112 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C113 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C132 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C133 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C201 1-128-995-21 ELECT CHIP 100uF 20% 10V
C202 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C203 1-128-995-21 ELECT CHIP 100uF 20% 10V
C204 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C205 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C206 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C207 1-128-995-21 ELECT CHIP 100uF 20% 10V
C208 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C210 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C213 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C214 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C215 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C217 1-164-360-11 CERAMIC CHIP 0.1uF 16V
BATTERY1
Ver. 1.1
BATTERY2 CD
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant le
numéro spécifié.
SP : Singapore model.
TH : Thai model.
TW : Taiwan model.
C218 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C219 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C220 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C221 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C222 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C223 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C224 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C226 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C227 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C230 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C232 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C251 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
C252 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C253 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
C254 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C256 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C257 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C258 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C259 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C260 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V
C261 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C264 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C265 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C267 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C268 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C269 1-126-208-21 ELECT CHIP 47uF 20% 4V
C270 1-126-208-21 ELECT CHIP 47uF 20% 4V
C271 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C272 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C273 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
C275 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C291 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
C292 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
C301 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C302 1-137-710-11 CERAMIC CHIP 10uF 20% 6.3V
C303 1-137-710-11 CERAMIC CHIP 10uF 20% 6.3V
C321 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C322 1-115-156-11 CERAMIC CHIP 1uF 10V
C323 1-128-995-21 ELECT CHIP 100uF 20% 10V
C401 1-128-396-11 ELECT CHIP 470uF 20% 10V
C404 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C405 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C406 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C424 1-164-360-11 CERAMIC CHIP 0.1uF 16V
39

ZS-SN10
Ver. 1.3
CD CONTROL (1) CONTROL (2)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C451 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V R322 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R323 1-216-864-11 SHORT CHIP 0
< CONNECTOR >
R324 1-216-845-11 METAL CHIP 100K 5% 1/10W
CN102 1-770-706-21 CONNECTOR, FFC/FPC 23P
CN301 1-770-425-51 CONNECTOR, FFC/FPC 16P
40
< IC >
IC201 8-753-239-32 IC CXD3014-201R
IC202 6-708-165-01 IC TK73325WTL-G
IC402 6-708-516-01 IC FAN8040G3
< TRANSISTOR >
Q321 6-551-120-01 TRANSISTOR 2SA2119K
< RESISTOR >
R101 1-216-809-11 METAL CHIP 100 5% 1/10W
R102 1-216-809-11 METAL CHIP 100 5% 1/10W
R103 1-216-809-11 METAL CHIP 100 5% 1/10W
R104 1-216-809-11 METAL CHIP 100 5% 1/10W
R105 1-216-809-11 METAL CHIP 100 5% 1/10W
R107 1-216-809-11 METAL CHIP 100 5% 1/10W
R108 1-216-809-11 METAL CHIP 100 5% 1/10W
R109 1-216-809-11 METAL CHIP 100 5% 1/10W
R110 1-216-809-11 METAL CHIP 100 5% 1/10W
R111 1-216-809-11 METAL CHIP 100 5% 1/10W
R112 1-216-809-11 METAL CHIP 100 5% 1/10W
R113 1-216-809-11 METAL CHIP 100 5% 1/10W
R115 1-216-864-11 SHORT CHIP 0
R201 1-216-295-91 SHORT CHIP 0
R202 1-216-295-91 SHORT CHIP 0
R203 1-216-295-91 SHORT CHIP 0
R207 1-216-295-91 SHORT CHIP 0
R249 1-216-841-11 METAL CHIP 47K 5% 1/10W
R250 1-216-857-11 METAL CHIP 1M 5% 1/10W
R252 1-216-833-11 METAL CHIP 10K 5% 1/10W
R253 1-216-821-11 METAL CHIP 1K 5% 1/10W
R254 1-216-833-11 METAL CHIP 10K 5% 1/10W
R255 1-216-821-11 METAL CHIP 1K 5% 1/10W
R256 1-216-837-11 METAL CHIP 22K 5% 1/10W
R257 1-216-853-11 METAL CHIP 470K 5% 1/10W
R258 1-216-849-11 METAL CHIP 220K 5% 1/10W
R259 1-216-833-11 METAL CHIP 10K 5% 1/10W
R260 1-216-864-11 SHORT CHIP 0
R265 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R266 1-216-821-11 METAL CHIP 1K 5% 1/10W
R267 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R268 1-216-833-11 METAL CHIP 10K 5% 1/10W
R270 1-216-817-11 METAL CHIP 470 5% 1/10W
R271 1-216-857-11 METAL CHIP 1M 5% 1/10W
R275 1-216-809-11 METAL CHIP 100 5% 1/10W
R276 1-216-841-11 METAL CHIP 47K 5% 1/10W
R277 1-216-809-11 METAL CHIP 100 5% 1/10W
R278 1-216-809-11 METAL CHIP 100 5% 1/10W
R280 1-216-864-11 SHORT CHIP 0
R291 1-216-809-11 METAL CHIP 100 5% 1/10W
R292 1-216-809-11 METAL CHIP 100 5% 1/10W
R321 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R325 1-216-864-11 SHORT CHIP 0
R326 1-216-864-11 SHORT CHIP 0
R401 1-216-295-91 SHORT CHIP 0
R421 1-216-864-11 SHORT CHIP 0
R423 1-216-833-11 METAL CHIP 10K 5% 1/10W
R451 1-216-837-11 METAL CHIP 22K 5% 1/10W
R452 1-216-833-11 METAL CHIP 10K 5% 1/10W
< VIBRATOR >
X202 1-767-408-21 VIBRATOR, CRYSTAL (16.9344MHz)
************************************************************
A-1105-375-A CONTROL (1) BOARD, COMPLETE
***************************
< CONNECTOR >
CN401 1-815-550-11 PIN, CONNECTOR (PWB) 2P
CN403 1-784-726-11 CONNECTOR, FFC 4P
< LED >
D401 8-719-059-97 LED L-34HD (OPR/BATT)
< RESISTOR >
R418 1-216-817-11 METAL CHIP 470 5% 1/10W
R419 1-216-817-11 METAL CHIP 470 5% 1/10W
R420 1-216-821-11 METAL CHIP 1K 5% 1/10W
R421 1-216-821-11 METAL CHIP 1K 5% 1/10W
R425 1-216-813-11 METAL CHIP 220 5% 1/10W
R426 1-216-813-11 METAL CHIP 220 5% 1/10W
R427 1-216-817-11 METAL CHIP 470 5% 1/10W
< SWITCH >
S402 1-786-050-21 SWITCH, KEY BOARD (POWER)
S403 1-786-050-21 SWITCH, KEY BOARD (SLEEP)
************************************************************
A-1105-376-A CONTROL (2) BOARD, COMPLETE
***************************
< RESISTOR >
R428 1-216-821-11 METAL CHIP 1K 5% 1/10W
R429 1-216-821-11 METAL CHIP 1K 5% 1/10W
R430 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R431 1-216-821-11 METAL CHIP 1K 5% 1/10W
R432 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
< SWITCH >
S404 1-786-050-21 SWITCH, KEY BOARD (VOLUME +)
S405 1-786-050-21 SWITCH, KEY BOARD (VOLUME –)
S406 1-786-050-21 SWITCH, KEY BOARD (MEGA BASS)
S407 1-786-050-21 SWITCH, KEY BOARD (SOUND)
************************************************************

ZS-SN10
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
A-1105-328-A H/P BOARD, COMPLETE
*******************
< CONNECTOR >
CN402 1-770-519-31 CONNECTOR, FFC/FPC 11P
< CAPACITOR >
CN405 1-770-519-31 CONNECTOR, FFC/FPC 11P
C119 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C219 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
< CONNECTOR >
* CN323 1-815-552-11 PIN, CONNECTOR (PWB) 4P
< FERRITE BEAD >
FB101 1-469-701-21 FERRITE, EMI (SMD) (1608)
FB201 1-469-701-21 FERRITE, EMI (SMD) (1608)
FB301 1-469-701-21 FERRITE, EMI (SMD) (1608)
< JACK >
J301 1-815-325-11 JACK (i)
J322 1-566-891-11 JACK (LINE IN)
< COIL >
L101 1-410-517-11 INDUCTOR 47uH
L201 1-410-517-11 INDUCTOR 47uH
L301 1-414-142-61 INDUCTOR 1uH
< RESISTOR >
R126 1-216-809-11 METAL CHIP 100 5% 1/10W
R226 1-216-809-11 METAL CHIP 100 5% 1/10W
************************************************************
A-1105-337-A LCD BOARD, COMPLETE (for BLACK, SILVER)
A-1124-479-A LCD BOARD, COMPLETE (for WHITE)
********************
2-582-131-01 HOLDER, LCD
2-582-138-01 PLATE, LIGHT GUIDE
2-582-152-01 ILLUMINATOR
< CAPACITOR >
C401 1-115-156-11 CERAMIC CHIP 1uF 10V
C402 1-115-156-11 CERAMIC CHIP 1uF 10V
C403 1-115-156-11 CERAMIC CHIP 1uF 10V
C404 1-115-156-11 CERAMIC CHIP 1uF 10V
C405 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C406 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C407 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C408 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C409 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C410 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C411 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C412 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C413 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C414 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C417 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C418 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C419 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C420 1-162-974-11 CERAMIC CHIP 0.01uF 50V
< LED >
D402 6-501-437-01 LED SLI-343YC3F (LCD BACK LIGHT)
(EXCEPT US (WHITE), CND (WHITE))
D402 6-500-863-01 LED SLR343EBT (LCD BACK LIGHT)
(US (WHITE), CND (WHITE))
< IC >
IC401 6-701-681-01 IC RPM7140-V4
< COIL >
L401 1-410-517-11 INDUCTOR 47uH
L402 1-414-142-61 INDUCTOR 1uH
L403 1-414-142-61 INDUCTOR 1uH
< LIQUID CRYSTAL DISPLAY >
LCD401 1-479-194-11 ELEMENT UNIT, LIQUID CRYSTAL I
< RESISTOR >
R401 1-216-821-11 METAL CHIP 1K 5% 1/10W
R402 1-216-821-11 METAL CHIP 1K 5% 1/10W
R415 1-216-841-11 METAL CHIP 47K 5% 1/10W
R416 1-216-845-11 METAL CHIP 100K 5% 1/10W
R417 1-216-853-11 METAL CHIP 470K 5% 1/10W
R436 1-216-813-11 METAL CHIP 220 5% 1/10W
R437 1-216-817-11 METAL CHIP 470 5% 1/10W
R438 1-216-821-11 METAL CHIP 1K 5% 1/10W
R439 1-216-821-11 METAL CHIP 1K 5% 1/10W
R440 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R446 1-216-813-11 METAL CHIP 220 5% 1/10W
R447 1-216-817-11 METAL CHIP 470 5% 1/10W
R448 1-216-821-11 METAL CHIP 1K 5% 1/10W
R449 1-216-821-11 METAL CHIP 1K 5% 1/10W
R450 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R451 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R452 1-216-821-11 METAL CHIP 1K 5% 1/10W
R453 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R454 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R458 1-216-817-11 METAL CHIP 470 5% 1/10W
R459 1-216-813-11 METAL CHIP 220 5% 1/10W
(US (WHITE), CND (WHITE))
R459 1-216-817-11 METAL CHIP 470 5% 1/10W
(EXCEPT US (WHITE), CND (WHITE))
R490 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R491 1-216-864-11 SHORT CHIP 0
R492 1-216-833-11 METAL CHIP 10K 5% 1/10W
R493 1-216-821-11 METAL CHIP 1K 5% 1/10W
R494 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
< SWITCH >
Ver. 1.3
H/P LCD
S401 1-478-528-11 ENCODER (ROTARY) (JOG)
S410 1-786-050-21 SWITCH, KEY BOARD (LINE)
S411 1-786-050-21 SWITCH, KEY BOARD
(RADIO/BAND, AUTO PRESET)
41

ZS-SN10
Ver. 1.3
LCD MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
S412 1-786-050-21 SWITCH, KEY BOARD (FOLDER/TUNE –)
S413 1-786-050-21 SWITCH, KEY BOARD (FOLDER/TUNE +)
S414 1-786-050-21 SWITCH, KEY BOARD (ENTER/MEMORY)
S418 1-786-050-21 SWITCH, KEY BOARD (u)
S419 1-786-050-21 SWITCH, KEY BOARD (x)
S420 1-786-050-21 SWITCH, KEY BOARD (> PRESET +)
S421 1-786-050-21 SWITCH, KEY BOARD (. PRESET –)
S422 1-786-050-21 SWITCH, KEY BOARD (REPEAT)
S423 1-786-050-21 SWITCH, KEY BOARD (MODE)
S424 1-786-050-21 SWITCH, KEY BOARD (DISPLAY)
S425 1-786-050-21 SWITCH, KEY BOARD (FOLDER SEARCH)
************************************************************
42
A-1105-346-A MAIN BOARD, COMPLETE (US, CND, E, MX)
A-1105-348-A MAIN BOARD, COMPLETE (SP, TH)
A-1105-349-A MAIN BOARD, COMPLETE (TW, KR, AUS)
*********************
2-594-013-01 PLATE (MAIN), SHIELD
3-253-143-01 SCREW (B2.6), (+) P TAPPING
< CAPACITOR >
C101 1-126-961-11 ELECT 2.2uF 20% 50V
C102 1-126-961-11 ELECT 2.2uF 20% 50V
C103 1-126-959-11 ELECT 0.47uF 20% 50V
C104 1-126-963-11 ELECT 4.7uF 20% 50V
C105 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C106 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C107 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C108 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C109 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C110 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C111 1-126-963-11 ELECT 4.7uF 20% 50V
C112 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C113 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C114 1-126-960-11 ELECT 1uF 20% 50V
C116 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C117 1-126-960-11 ELECT 1uF 20% 50V
C118 1-126-960-11 ELECT 1uF 20% 50V
C120 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C122 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C123 1-126-785-11 ELECT 47uF 20% 10V
(US, CND, E, MX)
C123 1-126-947-11 ELECT 47uF 20% 35V
(SP, TW, KR, TH, AUS)
C124 1-104-658-91 ELECT 100uF 20% 10V
C125 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C126 1-126-926-11 ELECT 1000uF 20% 10V
C127 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C201 1-126-961-11 ELECT 2.2uF 20% 50V
C202 1-126-961-11 ELECT 2.2uF 20% 50V
C203 1-126-959-11 ELECT 0.47uF 20% 50V
C204 1-126-963-11 ELECT 4.7uF 20% 50V
C205 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C206 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C207 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C208 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C209 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C210 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C211 1-126-963-11 ELECT 4.7uF 20% 50V
C212 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C213 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C214 1-126-960-11 ELECT 1uF 20% 50V
C216 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C217 1-126-960-11 ELECT 1uF 20% 50V
C218 1-126-960-11 ELECT 1uF 20% 50V
C220 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C222 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C223 1-126-785-11 ELECT 47uF 20% 10V
(US, CND, E, MX)
C223 1-126-947-11 ELECT 47uF 20% 35V
(SP, TW, KR, TH, AUS)
C224 1-104-658-91 ELECT 100uF 20% 10V
C225 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C226 1-126-926-11 ELECT 1000uF 20% 10V
C227 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C301 1-104-658-91 ELECT 100uF 20% 10V
C302 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C303 1-126-959-11 ELECT 0.47uF 20% 50V
C304 1-126-947-11 ELECT 47uF 20% 35V
C305 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C306 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C321 1-104-662-91 ELECT 22uF 20% 25V
C322 1-126-947-11 ELECT 47uF 20% 35V
C324 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C325 1-126-964-11 ELECT 10uF 20% 50V
C326 1-126-934-11 ELECT 220uF 20% 16V
C421 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C422 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C423 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C424 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C425 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C426 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C427 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C428 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C429 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C430 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C431 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C432 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C433 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C434 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C801 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C802 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C803 1-126-513-11 ELECT 47uF 20% 6.3V
(US, CND, E, MX)
C803 1-126-947-11 ELECT 47uF 20% 35V
(SP, TW, KR, TH, AUS)
C805 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C806 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C807 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C808 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C809 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C810 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C811 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C812 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C813 1-162-927-11 CERAMIC CHIP 100PF 5% 50V-
C814 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C815 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

ZS-SN10
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C816 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C817 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C818 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C819 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C820 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C821 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C822 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C823 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C824 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C825 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C826 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C827 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C828 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C829 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C830 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C831 1-115-156-11 CERAMIC CHIP 1uF 10V
C832 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C833 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C837 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C838 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C839 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C840 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C841 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C842 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C845 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C848 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C849 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C850 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C851 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C852 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C853 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C854 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C855 1-115-156-11 CERAMIC CHIP 1uF 10V
C856 1-115-156-11 CERAMIC CHIP 1uF 10V
C859 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C860 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C861 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C862 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C867 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C868 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C869 1-115-156-11 CERAMIC CHIP 1uF 10V
C870 1-126-964-11 ELECT 10uF 20% 50V
C871 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C872 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C873 1-126-926-11 ELECT 1000uF 20% 10V
C874 1-126-923-91 ELECT 220uF 20% 10V
C875 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C907 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C950 1-126-937-11 ELECT 4700uF 20% 16V
C951 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C952 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C953 1-126-923-91 ELECT 220uF 20% 10V
C954 1-104-658-91 ELECT 100uF 20% 10V
C955 1-126-923-91 ELECT 220uF 20% 10V
C956 1-104-658-91 ELECT 100uF 20% 10V
C957 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C958 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C959 1-126-934-11 ELECT 220uF 20% 16V
C960 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C961 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C963 1-126-964-11 ELECT 10uF 20% 50V
< CONNECTOR >
CN301 1-815-445-11 PIN, CONNECTOR (PWB) 4P
CN302 1-815-444-11 PIN, CONNECTOR (PWB) 3P
CN801 1-779-291-11 CONNECTOR, FFC (LIF (NON-ZIF)) 23P
CN802 1-568-830-11 CONNECTOR 11P
CN804 1-784-765-11 CONNECTOR, FFC 4P
CN806 1-568-830-11 CONNECTOR 11P
CN807 1-568-830-11 CONNECTOR 11P
CN901 1-815-445-21 PIN, CONNECTOR (PWB) 4P
< DIODE >
D301 8-719-082-07 DIODE KDS121-RTK
D801 8-719-082-07 DIODE KDS121-RTK
D802 8-719-069-54 DIODE UDZSTE-175.1B
D905 8-719-978-33 DIODE DTZ-TT11-6.8B
D906 8-719-988-61 DIODE 1SS355TE-17
D907 8-719-988-61 DIODE 1SS355TE-17
D908 8-719-988-61 DIODE 1SS355TE-17
D951 8-719-083-93 DIODE KDS120-RTK
D953 8-719-978-33 DIODE DTZ-TT11-6.8B
< FERRITE BEAD >
FB801 1-469-701-21 FERRITE, EMI (SMD) (1608)
FB802 1-469-701-21 FERRITE, EMI (SMD) (1608)
FB803 1-500-445-21 FERRITE, EMI (SMD) (2012)
FB804 1-500-445-21 FERRITE, EMI (SMD) (2012)
< IC >
IC301 6-701-824-11 IC BD3870FS-E2
IC304 8-759-426-51 IC BA5417
IC801 6-806-037-01 IC MB90483BPF-G-153E1
IC802 6-706-338-01 IC XC6202P332FR
IC803 6-703-224-01 IC S-80828CNNB-B8NT2G
IC804 6-704-004-01 IC BR24L16F-WE2
IC901 8-759-679-43 IC S-816A33AMC-BAI-T2-G
< JUMPER RESISTOR >
JC801 1-216-864-11 SHORT CHIP 0
JC802 1-216-864-11 SHORT CHIP 0
JC803 1-216-864-11 SHORT CHIP 0
JC804 1-216-864-11 SHORT CHIP 0
JC805 1-216-864-11 SHORT CHIP 0
JC806 1-216-864-11 SHORT CHIP 0
JC807 1-216-864-11 SHORT CHIP 0
JC808 1-216-864-11 SHORT CHIP 0
< COIL >
L801 1-410-509-11 INDUCTOR 10uH
L802 1-414-137-31 INDUCTOR 0.22uH
L803 1-414-142-61 INDUCTOR 1uH
L804 1-410-517-11 INDUCTOR 47uH
L806 1-414-142-61 INDUCTOR 1uH
L807 1-410-517-11 INDUCTOR 47uH
Ver. 1.3
MAIN
43

ZS-SN10
Ver. 1.3
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
44
< TRANSISTOR >
Q101 8-729-602-21 TRANSISTOR 2SC4154-F
Q121 8-729-029-10 TRANSISTOR DTC143TUA-T106
Q201 8-729-602-21 TRANSISTOR 2SC4154-F
Q221 8-729-029-10 TRANSISTOR DTC143TUA-T106
Q801 8-729-602-21 TRANSISTOR 2SC4154-F
Q802 8-729-602-21 TRANSISTOR 2SC4154-F
Q803 8-729-602-21 TRANSISTOR 2SC4154-F
Q804 8-729-028-76 TRANSISTOR DTA114YUA-T106
Q805 8-729-028-99 TRANSISTOR DTC114YUA-T106
Q806 8-729-028-99 TRANSISTOR DTC114YUA-T106
Q807 8-729-602-36 TRANSISTOR 2SA1602-F
Q808 8-729-028-99 TRANSISTOR DTC114YUA-T106
Q809 8-729-028-99 TRANSISTOR DTC114YUA-T106
Q810 8-729-028-76 TRANSISTOR DTA114YUA-T106
Q811 6-551-420-01 TRANSISTOR RT1N151M-TP-1
Q812 6-551-424-01 TRANSISTOR RT1P151M-TP-1
Q813 8-729-602-36 TRANSISTOR 2SA1602-F
Q821 6-551-424-01 TRANSISTOR RT1P151M-TP-1
Q822 6-551-420-01 TRANSISTOR RT1N151M-TP-1
Q823 8-729-602-21 TRANSISTOR 2SC4154-F
Q824 8-729-037-13 TRANSISTOR KTA1271Y
Q951 6-551-422-01 TRANSISTOR RT1N436M-TP-1
Q952 8-729-040-76 TRANSISTOR KTA1273-Y-AT
Q953 8-729-602-21 TRANSISTOR 2SC4154-F
Q954 8-729-018-99 TRANSISTOR 2SD2394-F
Q955 8-729-036-86 TRANSISTOR KTC3203Y-AT
Q956 8-729-101-07 TRANSISTOR 2SB798-DL
< RESISTOR >
R101 1-216-833-11 METAL CHIP 10K 5% 1/10W
R102 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R103 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R104 1-216-821-11 METAL CHIP 1K 5% 1/10W
R105 1-216-833-11 METAL CHIP 10K 5% 1/10W
R106 1-216-841-11 METAL CHIP 47K 5% 1/10W
R110 1-216-833-11 METAL CHIP 10K 5% 1/10W
R111 1-216-821-11 METAL CHIP 1K 5% 1/10W
R112 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R113 1-216-853-11 METAL CHIP 470K 5% 1/10W
R114 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R115 1-216-821-11 METAL CHIP 1K 5% 1/10W
R116 1-216-813-11 METAL CHIP 220 5% 1/10W
R117 1-216-817-11 METAL CHIP 470 5% 1/10W
R118 1-216-864-11 SHORT CHIP 0
R119 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R120 1-216-841-11 METAL CHIP 47K 5% 1/10W
R121 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R122 1-216-813-11 METAL CHIP 220 5% 1/10W
R123 1-216-817-11 METAL CHIP 470 5% 1/10W
R124 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R125 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R127 1-216-864-11 SHORT CHIP 0
R201 1-216-833-11 METAL CHIP 10K 5% 1/10W
R202 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R203 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R204 1-216-821-11 METAL CHIP 1K 5% 1/10W
R205 1-216-833-11 METAL CHIP 10K 5% 1/10W
R206 1-216-841-11 METAL CHIP 47K 5% 1/10W
R210 1-216-833-11 METAL CHIP 10K 5% 1/10W
R211 1-216-821-11 METAL CHIP 1K 5% 1/10W
R212 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R213 1-216-853-11 METAL CHIP 470K 5% 1/10W
R214 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R215 1-216-821-11 METAL CHIP 1K 5% 1/10W
R216 1-216-813-11 METAL CHIP 220 5% 1/10W
R217 1-216-817-11 METAL CHIP 470 5% 1/10W
R218 1-216-864-11 SHORT CHIP 0
R219 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R220 1-216-841-11 METAL CHIP 47K 5% 1/10W
R221 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R222 1-216-813-11 METAL CHIP 220 5% 1/10W
R223 1-216-817-11 METAL CHIP 470 5% 1/10W
R224 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R225 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R227 1-216-864-11 SHORT CHIP 0
R301 1-216-809-11 METAL CHIP 100 5% 1/10W
R302 1-216-809-11 METAL CHIP 100 5% 1/10W
R303 1-216-833-11 METAL CHIP 10K 5% 1/10W
R304 1-216-833-11 METAL CHIP 10K 5% 1/10W
R305 1-216-821-11 METAL CHIP 1K 5% 1/10W
R306 1-216-821-11 METAL CHIP 1K 5% 1/10W
R309 1-216-833-11 METAL CHIP 10K 5% 1/10W
R321 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R322 1-216-821-11 METAL CHIP 1K 5% 1/10W
R323 1-216-833-11 METAL CHIP 10K 5% 1/10W
R324 1-216-857-11 METAL CHIP 1M 5% 1/10W
R325 1-216-821-11 METAL CHIP 1K 5% 1/10W
R326 1-216-821-11 METAL CHIP 1K 5% 1/10W
R468 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R469 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R470 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R471 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R472 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R473 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R474 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R475 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R476 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R477 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R478 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R479 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R480 1-216-821-11 METAL CHIP 1K 5% 1/10W
R481 1-216-821-11 METAL CHIP 1K 5% 1/10W
R483 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R484 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R485 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R486 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R488 1-216-833-11 METAL CHIP 10K 5% 1/10W
R495 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R496 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R497 1-216-845-11 METAL CHIP 100K 5% 1/10W
R498 1-216-797-11 METAL CHIP 10 5% 1/10W
R499 1-216-813-11 METAL CHIP 220 5% 1/10W

ZS-SN10
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R800 1-216-853-11 METAL CHIP 470K 5% 1/10W
R801 1-216-833-11 METAL CHIP 10K 5% 1/10W
(TW, KR, AUS)
R802 1-216-833-11 METAL CHIP 10K 5% 1/10W
(EXCEPT TW, KR, AUS)
R803 1-216-833-11 METAL CHIP 10K 5% 1/10W
R805 1-216-833-11 METAL CHIP 10K 5% 1/10W
(SP, TW, KR, TH, AUS)
R806 1-216-833-11 METAL CHIP 10K 5% 1/10W
(US, CND, E, MX)
R807 1-216-817-11 METAL CHIP 470 5% 1/10W
R808 1-216-817-11 METAL CHIP 470 5% 1/10W
R811 1-216-833-11 METAL CHIP 10K 5% 1/10W
R812 1-216-849-11 METAL CHIP 220K 5% 1/10W
R813 1-216-849-11 METAL CHIP 220K 5% 1/10W
R815 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R816 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R817 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R818 1-216-837-11 METAL CHIP 22K 5% 1/10W
R825 1-216-821-11 METAL CHIP 1K 5% 1/10W
R826 1-216-821-11 METAL CHIP 1K 5% 1/10W
R827 1-216-821-11 METAL CHIP 1K 5% 1/10W
R828 1-216-841-11 METAL CHIP 47K 5% 1/10W
R829 1-216-821-11 METAL CHIP 1K 5% 1/10W
R830 1-216-809-11 METAL CHIP 100 5% 1/10W
R831 1-216-813-11 METAL CHIP 220 5% 1/10W
R832 1-216-809-11 METAL CHIP 100 5% 1/10W
R833 1-216-821-11 METAL CHIP 1K 5% 1/10W
R834 1-216-821-11 METAL CHIP 1K 5% 1/10W
R835 1-216-821-11 METAL CHIP 1K 5% 1/10W
R836 1-216-821-11 METAL CHIP 1K 5% 1/10W
R837 1-216-821-11 METAL CHIP 1K 5% 1/10W
R838 1-216-821-11 METAL CHIP 1K 5% 1/10W
R839 1-216-821-11 METAL CHIP 1K 5% 1/10W
R840 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R841 1-216-821-11 METAL CHIP 1K 5% 1/10W
R842 1-216-821-11 METAL CHIP 1K 5% 1/10W
R844 1-216-837-11 METAL CHIP 22K 5% 1/10W
R845 1-216-841-11 METAL CHIP 47K 5% 1/10W
R846 1-216-833-11 METAL CHIP 10K 5% 1/10W
R847 1-216-821-11 METAL CHIP 1K 5% 1/10W
R848 1-216-821-11 METAL CHIP 1K 5% 1/10W
R849 1-216-821-11 METAL CHIP 1K 5% 1/10W
R850 1-216-821-11 METAL CHIP 1K 5% 1/10W
R851 1-216-821-11 METAL CHIP 1K 5% 1/10W
R852 1-216-841-11 METAL CHIP 47K 5% 1/10W
R853 1-216-833-11 METAL CHIP 10K 5% 1/10W
R854 1-216-833-11 METAL CHIP 10K 5% 1/10W
R855 1-216-833-11 METAL CHIP 10K 5% 1/10W
R856 1-216-833-11 METAL CHIP 10K 5% 1/10W
R858 1-216-841-11 METAL CHIP 47K 5% 1/10W
R859 1-216-864-11 SHORT CHIP 0
R862 1-216-821-11 METAL CHIP 1K 5% 1/10W
R863 1-216-833-11 METAL CHIP 10K 5% 1/10W
R864 1-216-841-11 METAL CHIP 47K 5% 1/10W
R865 1-216-845-11 METAL CHIP 100K 5% 1/10W
R866 1-216-833-11 METAL CHIP 10K 5% 1/10W
R867 1-216-853-11 METAL CHIP 470K 5% 1/10W
R868 1-216-821-11 METAL CHIP 1K 5% 1/10W
R869 1-216-821-11 METAL CHIP 1K 5% 1/10W
R870 1-216-821-11 METAL CHIP 1K 5% 1/10W
R871 1-216-821-11 METAL CHIP 1K 5% 1/10W
R872 1-216-821-11 METAL CHIP 1K 5% 1/10W
R873 1-216-813-11 METAL CHIP 220 5% 1/10W
R874 1-216-813-11 METAL CHIP 220 5% 1/10W
R875 1-216-821-11 METAL CHIP 1K 5% 1/10W
R876 1-216-821-11 METAL CHIP 1K 5% 1/10W
R877 1-216-821-11 METAL CHIP 1K 5% 1/10W
R878 1-216-809-11 METAL CHIP 100 5% 1/10W
R879 1-216-821-11 METAL CHIP 1K 5% 1/10W
R880 1-216-821-11 METAL CHIP 1K 5% 1/10W
R881 1-216-821-11 METAL CHIP 1K 5% 1/10W
R882 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R883 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R884 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R886 1-216-849-11 METAL CHIP 220K 5% 1/10W
R887 1-216-849-11 METAL CHIP 220K 5% 1/10W
R888 1-216-849-11 METAL CHIP 220K 5% 1/10W
R891 1-216-821-11 METAL CHIP 1K 5% 1/10W
R892 1-216-813-11 METAL CHIP 220 5% 1/10W
R893 1-216-841-11 METAL CHIP 47K 5% 1/10W
R894 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R895 1-216-821-11 METAL CHIP 1K 5% 1/10W
R896 1-216-833-11 METAL CHIP 10K 5% 1/10W
R899 1-216-833-11 METAL CHIP 10K 5% 1/10W
R900 1-216-821-11 METAL CHIP 1K 5% 1/10W
R901 1-216-821-11 METAL CHIP 1K 5% 1/10W
R902 1-216-821-11 METAL CHIP 1K 5% 1/10W
R903 1-216-821-11 METAL CHIP 1K 5% 1/10W
R950 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R951 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R952 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R953 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R954 1-216-833-11 METAL CHIP 10K 5% 1/10W
R955 1-216-833-11 METAL CHIP 10K 5% 1/10W
R956 1-216-841-11 METAL CHIP 47K 5% 1/10W
R957 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R958 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R959 1-216-821-11 METAL CHIP 1K 5% 1/10W
R960 1-216-821-11 METAL CHIP 1K 5% 1/10W
R961 1-216-821-11 METAL CHIP 1K 5% 1/10W
< VIBRATOR >
X801 1-813-175-21 VIBRATOR, CERAMIC (4.19MHz)
X802 1-795-915-11 VIBRATOR, CRYSTAL (32.768kHz)
************************************************************
A-1105-360-A POWER BOARD, COMPLETE
**********************
1-533-233-31 FUSE HOLDER
< CAPACITOR >
MAIN
Ver. 1.2
POWER
C901 1-162-995-11 CERAMIC CHIP 0.022uF 50V
C902 1-162-995-11 CERAMIC CHIP 0.022uF 50V
C903 1-162-995-11 CERAMIC CHIP 0.022uF 50V
45

ZS-SN10
Ver. 1.2
POWER TUNER
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C904 1-162-995-11 CERAMIC CHIP 0.022uF 50V
C906 1-126-964-11 ELECT 10uF 20% 50V
46
C908 1-165-128-11 CERAMIC CHIP 0.22uF 16V
< CONNECTOR >
CN903 1-815-551-11 PIN, CONNECTOR (PWB) 3P
< DIODE >
D901 8-719-063-79 DIODE 1N4002B
D902 8-719-063-79 DIODE 1N4002B
D903 8-719-063-79 DIODE 1N4002B
D904 8-719-063-79 DIODE 1N4002B
************************************************************
A-1105-354-A TUNER BOARD, COMPLETE (US, CND, E, MX)
A-1105-355-A TUNER BOARD, COMPLETE
(SP, TW, KR, TH, AUS)
**********************
2-582-141-01 TERMINAL, ANT
< CAPACITOR >
C1 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C4 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C7 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C8 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C9 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C10 1-126-960-11 ELECT 1uF 20% 50V
C11 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C12 1-126-963-11 ELECT 4.7uF 20% 50V
C13 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
(US, CND, E, MX)
C14 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
(SP, TW, KR, TH, AUS)
C14 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
(US, CND, E, MX)
C15 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
(SP, TW, KR, TH, AUS)
C15 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
(US, CND, E, MX)
C18 1-126-923-91 ELECT 220uF 20% 10V
C20 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C21 1-126-960-11 ELECT 1uF 20% 50V
C22 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C23 1-126-960-11 ELECT 1uF 20% 50V
C24 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
C26 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C27 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C29 1-104-658-91 ELECT 100uF 20% 10V
C30 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C31 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C32 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C33 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C34 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C35 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C37 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C39 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C41 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C42 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C43 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C47 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C49 1-161-051-00 CERAMIC 0.01uF 10% 25V
C51 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C52 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C53 1-137-190-91 FILM 0.22uF 5% 50V
C54 1-126-923-91 ELECT 220uF 20% 10V
C55 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C56 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C57 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C59 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C60 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C61 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C62 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C63 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C65 1-126-963-11 ELECT 4.7uF 20% 50V
C66 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C68 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C77 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
(SP, TW, KR, TH, AUS)
C78 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
(SP, TW, KR, TH, AUS)
C80 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C95 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
< FILTER >
CF2 1-760-235-81 FILTER, CERAMIC
CF4 1-781-962-21 FILTER, CERAMIC
< CONNECTOR >
CNP1 1-568-854-11 CONNECTOR 11P
< TRIMMER >
CT1 1-141-442-91 CAP, CERAMIC TRIMMER
CT3 1-141-304-21 CAP, CERAMIC TRIMMER
< DIODE >
D1 8-719-078-48 DIODE KV1471ETR-G
D2 8-719-078-48 DIODE KV1471ETR-G
D3 8-719-050-69 DIODE KV1520N
D10 8-719-988-61 DIODE 1SS355TE-17
D11 8-719-988-61 DIODE 1SS355TE-17
< IC >
IC1 6-700-512-01 IC TA2149BN
IC2 8-759-483-40 IC LC72137M-TLM-E
< JUMPER RESISTOR >
JC1 1-216-864-11 SHORT CHIP 0
JC2 1-216-864-11 SHORT CHIP 0
JC3 1-216-864-11 SHORT CHIP 0
JC4 1-216-864-11 SHORT CHIP 0
JC5 1-216-864-11 SHORT CHIP 0
JC6 1-216-864-11 SHORT CHIP 0
JC11 1-216-864-11 SHORT CHIP 0
JC12 1-216-864-11 SHORT CHIP 0
JC13 1-216-864-11 SHORT CHIP 0
JC24 1-216-864-11 SHORT CHIP 0 (SP, TW, KR, TH, AUS)

ZS-SN10
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
JC33 1-216-864-11 SHORT CHIP 0
JC34 1-216-864-11 SHORT CHIP 0
< COIL >
L1 1-409-775-11 COIL, AIR-CORE
L2 1-416-509-11 COIL, AIR-CORE
L3 1-754-117-12 ANTENNA, FERRITE-ROD (MW)
L4 1-411-234-21 COIL, AM OSC
L11 1-414-142-11 INDUCTOR 1uH (US, CND, E, MX)
L21 1-410-509-11 INDUCTOR 10uH
< RESISTOR >
R1 1-216-817-11 METAL CHIP 470 5% 1/10W
R2 1-216-817-11 METAL CHIP 470 5% 1/10W
R3 1-216-833-11 METAL CHIP 10K 5% 1/10W
R4 1-216-833-11 METAL CHIP 10K 5% 1/10W
R5 1-216-821-11 METAL CHIP 1K 5% 1/10W
R10 1-216-805-11 METAL CHIP 47 5% 1/10W
R11 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R13 1-216-821-11 METAL CHIP 1K 5% 1/10W
R14 1-216-821-11 METAL CHIP 1K 5% 1/10W
R24 1-216-813-11 METAL CHIP 220 5% 1/10W
R30 1-216-837-11 METAL CHIP 22K 5% 1/10W
R31 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R32 1-216-845-11 METAL CHIP 100K 5% 1/10W
R33 1-216-833-11 METAL CHIP 10K 5% 1/10W
R40 1-216-849-11 METAL CHIP 220K 5% 1/10W
R41 1-216-833-11 METAL CHIP 10K 5% 1/10W
R50 1-216-821-11 METAL CHIP 1K 5% 1/10W
R51 1-216-833-11 METAL CHIP 10K 5% 1/10W
R52 1-216-864-11 SHORT CHIP 0
R53 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R54 1-216-817-11 METAL CHIP 470 5% 1/10W
R55 1-216-833-11 METAL CHIP 10K 5% 1/10W
R56 1-216-813-11 METAL CHIP 220 5% 1/10W
R57 1-216-809-11 METAL CHIP 100 5% 1/10W
R58 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R59 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R60 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R61 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R63 1-216-833-11 METAL CHIP 10K 5% 1/10W
R65 1-216-833-11 METAL CHIP 10K 5% 1/10W
R91 1-216-813-11 METAL CHIP 220 5% 1/10W
R92 1-216-813-11 METAL CHIP 220 5% 1/10W
R94 1-216-821-11 METAL CHIP 1K 5% 1/10W
< TRANSFORMER >
T1 1-433-741-11 TRANSFORMER, IF
T2 1-419-465-11 COIL (DET)
< VIBRATOR >
X1 1-795-449-11 VIBRATOR, CRYSTAL (75kHz)
************************************************************
MISCELLANEOUS
**************
6 1-831-915-11 CABLE, FLEXIBLE FLAT (4 CORE)
64 1-831-926-11 CABLE, FLEXIBLE FLAT (11 CORE)
105 1-452-899-11 MAGNET
160 1-828-377-51 WIRE (FLAT TYPE) (23 CORE)
163 1-832-404-21 WIRE (FLAT TYPE) (16 CORE)
208 1-827-720-51 WIRE (FLAT TYPE) (11 CORE)
0 501 8-848-483-12 OPTICAL PICK-UP (KSS-213C/C2RP1)
505 X-2162-709-2 CHASSIS ASSY (CDP), MOTOR
(including M401 (SPINDLE))
ANT1 1-754-241-11 ANTENNA, TELESCOPIC
0 F902 1-533-450-12 FUSE, GLASS TUBE (DIA. 5) (2.5A/125V)
(US, CND, E, MX, TW)
0 F902 1-533-468-12 FUSE, GLASS TUBE (DIA. 5) (T2AL/250V)
(SP, KR, TH, AUS)
0 J901 1-526-818-11 INLET, AC (E, MX)
0 J901 1-526-838-11 INLET, AC 2P (SP, TW, KR, TH, AUS)
0 J901 1-540-009-11 INLET, AC (US, CND)
M402 X-2625-769-1 GEAR ASSY (MB) (RP), MOTOR (SLED)
S201 1-771-853-11 SWITCH, DETECTION (LIMIT)
S801 1-692-960-21 SWITCH, PUSH (1 KEY)
(CD LID OPEN/CLOSE DETECT)
SP101 1-826-212-11 SPEAKER (10cm) (L-ch)
SP201 1-826-212-11 SPEAKER (10cm) (R-ch)
0 T901 1-435-917-22 TRANSFORMER, POWER (US, CND, E, MX, TW)
0 T901 1-435-918-22 TRANSFORMER, POWER (SP, KR, TH, AUS)
************************************************************
ACCESSORIES
***********
0 1-590-342-12 CORD, POWER (E, MX)
0 1-769-412-22 CORD, POWER (SP, TH)
0 1-776-985-12 CORD, POWER (KR)
0 1-782-126-11 CORD, POWER (US, CND)
0 1-827-945-12 CORD, POWER (AUS)
Ver. 1.3
TUNER
0 1-829-433-11 CORD, POWER (TW)
2-593-810-12 MANUAL, INSTRUCTION (ENGLISH)
(US, CND, E, TW)
2-593-810-21 MANUAL, INSTRUCTION (FRENCH) (CND)
2-593-810-31 MANUAL, INSTRUCTION (ENGLISH, SPANISH)
(SP, KR, TH, AUS)
2-593-810-41 MANUAL, INSTRUCTION (FRENCH, GERMAN)
(SP)
2-593-811-11 MANUAL, INSTRUCTION (SPANISH) (E, MX)
2-593-811-21 MANUAL, INSTRUCTION (KOREAN) (KR)
2-593-811-31 MANUAL, INSTRUCTION
(TRADITIONAL CHINESE) (TW)
2-598-716-11 MANUAL, INSTRUCTION (for SonicStage)
(ENGLISH) (US, CND, E, TW)
2-598-716-21 MANUAL, INSTRUCTION (for SonicStage)
(FRENCH) (CND)
2-598-716-31 MANUAL, INSTRUCTION (for SonicStage)
(ENGLISH, SPANISH) (SP, KR, TH, AUS)
2-598-716-41 MANUAL, INSTRUCTION (for SonicStage)
(FRENCH, GERMAN) (SP)
2-598-717-11 MANUAL, INSTRUCTION (for SonicStage)
(KOREAN) (KR)
2-598-717-21 MANUAL, INSTRUCTION (for SonicStage)
(TRADITIONAL CHINESE) (TW)
47

ZS-SN10
Ver. 1.1
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
48
2-598-717-31 MANUAL, INSTRUCTION (for SonicStage)
(SPANISH) (E, MX)
3-267-151-01 LID BATTERY (for RMT-CYN7A)
(for BLACK, SILVER)
3-267-151-21 LID BATTERY (for RMT-CYN7A) (for WHITE)
A-1056-325-A REMOTE COMMANDER (RMT-CYN7A/HC)
(for SILVER)
A-1109-498-A REMOTE COMMANDER (RMT-CYN7A/BC)
(for BLACK)
A-1109-500-A REMOTE COMMANDER (RMT-CYN7A/WC)
(for WHITE)
X-2059-463-1 CD-ROM (APPLICATION) ASSY (SS3.0)
(SonicStage)

ZS-SN10
MEMO
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
49

ZS-SN10
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
2
Ver. Date Description of Revision
1.0 2005.04 New
1.1 2005.06 Addition of Thai model
Revision of electrical parts
Revision of mechanical parts
1.2 2005.07 Addition of E model
1.3 2006.02 Addition of silver type to US model
Revision of electrical parts
1.4 2006.03 Addition of silver type to Canadian model
Revision of mechanical parts