2008 CATALOG WWW.ICCINK.COM

More documents

Recommendations

Info

3810 BLOWOUT BASE International Coatings introduces a brand new special effects ink - 3810 BlowOut Base. Upon curing the ink through the dryer, 3810 BlowOut Base will blister and bubble up to form a unique spongy and textured surface. Like International Coatings’ High Density and Special FX Clear products, 3810 BlowOut Base can be used as a stand-alone product or in combination with other inks (including other special effects inks) to produce a wide range of new looks. 3810 BlowOut Base is versatile and can be printed in a variety of different ways to create new textures and fashions. For example, longer or repeated exposure to heat will increase the height and texture of the ink surface. 3810 BlowOut Base can be tinted using International Coatings’ 7400 Series Color Concentrates or can be printed on top or underneath other plastisol inks. The combinations and effects are limited only by one’s imagination. www.iccink.com 13929 East 166th Street, Cerritos, CA 90702-7666 Tel: 1 (562) 926-1010 • Toll Free (US only): 1 (800) 425-4103 • Fax: 1 (562) 926-9486 68
FEATURES �� 3810 LF* BlowOut Base Special Effects ink. �� Used to create very uniquely textured, spongy surfaces. �� Use as a stand-alone product or in combination with other inks such as International Coatings’ Granite Base or 7400 UltraMix® Color Concentrates to create a variety of new textures and looks. Application & Storage Information RE<strong>COM</strong>MENDED FABRICS INK APPLICATION SCREEN MESH AND EMULSION SQUEEGEE CURE TEMPERATURES 100% cotton and some polyester or cotton/polyester blends. Use as an under base or as is. Always test print for bleeding or dye migration. BlowOut Base can be printed with or without any modifications depending on the desired results. Thinning of this product is not recommended. 83 to 160 t/in or 32 to 63 t/cm Monofilament Any direct or indirect lacquer resistant emulsion. 200 to 700 Micron Capillary Film 60-70 Durometer: Sharp or rounded Edge 60-90-60 or 70-90-70 Triple Durometer: Sharp or Rounded Edge 325°F (163°C) Entire ink film. Test dryer temperatures and wash test printed product before and during a production run. CLEAN-UP Any environmentally friendly plastisol screen wash. PRODUCT PACKAGING 1 Gallon, 5 Gallon, or 30 Gallon Containers. STORAGE OF INK CONTAINERS Recommend storage at 65°F to 90°F (18°C to 32°C). Avoid storage in direct sunlight. Keep containers well sealed. PRODUCT MSDS Refer to Material Safety Data Sheet MSDS8 3810 BLOWOUT BASE 13929 East 166th Street • Cerritos, California, USA 90702-7666 • Tel (562) 926-1010 • Fax (562) 926-9486 • www.iccink.com �� Very creamy, short bodied ink, with low tack for ease of printing. �� For use on 100% cotton and some polyester or cotton/ polyester blends. *LF (Lead Free) Contains less than 0.025% lead. MODIFYING INK Due to its unique properties, 3810 LF BlowOut Base can be modified to produce many varied looks and textures. Modified BlowOut Base should only be used in production after thorough testing of the modified product. Always test for wash fastness before beginning a production run. SPOT FLASHING 3810 LF BlowOut Base will spot dry, with very low after-flash tack, in 3 to 8 seconds depending on the spot dryer used. Too much heat / time may cause the ink to become sticky after flashing. Adjust flash unit accordingly. When spot drying, the ink should be just dry to the touch, with no lift off, but not totally fused. Totally fusing the ink may cause inter-coat adhesion problems with the inks printed on top of the flashed ink. Final curing I fusing should occur in the dryer. CREATIVITY 3810 LF BlowOut Base allows the printer to create unique, assorted textures and looks using a variety of print techniques and ink modifications. From adding color concentrates to BlowOut Base or overprinting, under basing or mixing in metallic inks, the potential of BlowOut Base is only limited to the user’s creativity. Running the BlowOut Base through the dryer at higher than recommended temperatures or longer dwell times will also create a variety of different looks. IMPORTANT INFORMATION 1. 3810 LF BlowOut Base is not a bleed resistant ink and on some types of fabric, bleeding or dye migration may occur. Always test for possible dye migration before beginning a production run. Bleeding or dye migration may not occur right away. 2. Always stir 3810 LF BlowOut Base before using. 3. 3810 LF BlowOut Base is a semi-translucent base and should be mixed with other inks or color concentrates or over-printed with other inks to achieve more opacity on dark fabrics. Properly setting squeegee, flood bar and off-contact will improve print performance of the ink. 5. It is extremely important to keep 3810 LF BlowOut Base from getting too hot in storage. Temperatures above 90°F (32°C) may cause the ink to thicken to a point where the ink may be difficult to use. 3810 BlowOut Base Recommendations and statements made are based on International Coatings’ research and experience. Since International Coatings does not have any control over the conditions of use or storage of the product sold, International Coatings cannot guarantee the results obtained through use of its products. All products are sold and samples given without any representation of warranty, expressed or implied, of fitness for any particular purpose or otherwise, and upon condition that the buyer shall determine the suitability of the product for its own purpose. This applies also where rights of third parties are involved. It does not release the user from the obligation to test the suitability of the product for the intended purpose and application. All trademarks noted herein are either the property of International Coatings, Pantone, Inc. or their respective companies. 69
Page 1 and 2:
2008 CATALOG VOL. VII WWW.ICCINK.CO
Page 3:
CONTENTS This CD was designed to sh
Page 9 and 10:
McLogan Supply Company Inc 345 16th
Page 11 and 12:
Nazdar Michigan 687 Minnesota Avenu
Page 13 and 14:
SOUTH CAROLINA Nazdar Greensboro 70
Page 15 and 16:
INTERNATIONAL DISTRIBUTORS GUATEMAL
Page 17 and 18: INTERNATIONAL COATINGS DIRECT PRINT
Page 19 and 20: Application & Storage Information R
Page 21 and 22: 700 SERIES PLASTISOL INKS 13929 Eas
Page 23 and 24: 13929 East 166th Street • Cerrito
Page 27 and 28: FEATURES FEATURES � Ready for use
Page 31 and 32: Creating Performance Solutions 1392
Page 33 and 34: 7040 BLOCKER GRAY 7040 Blocker Gray
Page 47 and 48: 800 SERIES LF OPAQUE The 800 Series
Page 49 and 50: UltraMix ® 1200 PVC-FREE COLOR SYS
Page 52 and 53: UltraMix ® 7400 LF International C
Page 54 and 55: UltraMix ® 7900 LF PF Extra Low Cu
Page 56 and 57: UltraMix ® 9000 LF NYLON The Ultra
Page 59: UltraMix ® 11000 LF ATHLETIC The U
Page 64 and 65: SPECIALTY PRODUCTS When vibrant col
Page 66 and 67: 3805 LF SUPER STRETCH CLEAR This sp
Page 70 and 71: 3811 GRANITE BASE 3811 Granite Base
Page 72 and 73: 3802 FOIL RESIST ADDITIVE Internati
Page 76 and 77: Ink Modifiers: 1110LF Curable Reduc
Page 88 and 89: TRANSFER PRODUCTS Add dimension and
Page 90 and 91: INSTA GRAPHIC SYSTEMS ® HEAT SEAL
Page 92 and 93: Model 138 Digital Manual Clam Press
Page 94 and 95: FOREVER DIGITAL TRANSFER PAPERS Int
Page 96 and 97: Forever Paper U.S. Distributors Pur
Page 98 and 99: Digital transfer PaPers fOr laser P
Page 100 and 101: Digital transfer PaPers fOr large f
Page 102 and 103: Digital transfer PaPers fOr ink jet
Page 104 and 105: Digital transfer PaPers fOr cOlOr c
Page 106 and 107: for almost two decades now, fOreVer
Page 108 and 109: OPTILUX ULTRA REFLECTIVE INK Intern
Page 110 and 111: Optilux Ultra Refl ective Ink Syste
Page 112 and 113: Optilux TM Reflective Film & Transf
Page 114 and 115: Special Effects Print Techniques Th
Page 116 and 117: Jacket Linings Jackets come in four
Page 118 and 119:
Pre-Heating Because nylon fabric ch
Page 120 and 121:
HOT PEEL OR HOT SPLIT TRANSFERS TRA
Page 122 and 123:
INTERNATIONAL COATINGS TRANSFER PRO
Page 124 and 125:
FABRIC DISCOLORATION AND HOW TO PRE
Page 126 and 127:
At what temperature do your inks cu
Page 128 and 129:
Can I intermix other companies’ i
Page 130 and 131:
MATERIAL SAFETY DATA SHEETS (MSDS)
Page 132 and 133:
MATERIAL SAFETY DATA SHEET PRODUCT
Page 134 and 135:
MATERIAL SAFETY DATA SHEET PRODUCT
Page 136:
Code Definition H: Health 3 F: Flam
show all

2008 CATALOG WWW.ICCINK.COM

Create successful ePaper yourself

Delete template?

Save as template?