2008 CATALOG WWW.ICCINK.COM
2008 CATALOG WWW.ICCINK.COM
2008 CATALOG WWW.ICCINK.COM
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
13929 East 166th Street • Cerritos, California, USA 90702-7666 • Tel (562) 926-1010 • Fax (562) 926-9486 • www.iccink.com<br />
FEATURE EATURE EATURES<br />
EATURE<br />
� 720LF* Softhand Clear is a super clear, curable extender base plastisol.<br />
� This product is formulated to soften, extend and increase the flow characteristics of most<br />
plastisol inks.<br />
*LF (Lead Free) Contains less than 0.025% lead.<br />
Application & Storage Information<br />
HOW TO USE<br />
CURE TEMPERATURE<br />
CLEAN-UP<br />
STORAGE OF INK<br />
CONTAINERS<br />
720 SOFTHAND CLEAR BASE<br />
720LF Softhand can be added to 700 Series,<br />
Multipurpose, 1100 Series, 7000 Series and 800 Series<br />
inks for improved hand, cost and printability. 720LF is<br />
very clear and is highly recommended for extending<br />
any process color, especially the Pro-Brite Process<br />
Colors.<br />
For a softer hand, add approximately 10% to 20%, by<br />
volume, of 720LF Softhand Clear. More may be added,<br />
if necessary, without affecting the cure or fusing of the<br />
mixed ink. The more Softhand added, the less opaque<br />
the mixed ink will be.<br />
Using the 720LF Softhand in 800 Series inks to print on<br />
light colored fabrics greatly lowers the cost of the<br />
mixed ink. Adding 720LF Softhand to 800 Series inks<br />
in amounts higher than 20%, by volume, may shift<br />
mixed Pantone colors.<br />
NOTE: The addition of 720LF Softhand Clear reduces<br />
the bleed resistance of low bleed inks.<br />
325°F (163°C) entire ink film. Fusion temperature may<br />
vary, depending on which inks 720LF Softhand is mixed<br />
into.<br />
Since plastisols do not air dry, they must be fused with<br />
an appropriate heat source in order to achieve<br />
durability. The optimum time/temperature cycle will<br />
vary with the amount of ink deposited, fabric and the<br />
type of heat source used. Plastisols actually achieve<br />
the proper fusion point as soon as the innermost<br />
section of the ink film reaches the prescribed<br />
temperature. Test dryer temperatures before a<br />
production run. Wash test printed product before<br />
production run.<br />
Environmentally friendly plastisol screen wash or<br />
mineral spirits.<br />
Keep inks indoor and store in a cool area. Recommend<br />
storage at 65°F to 90°F (18°C to 32°C). Avoid storage<br />
in direct sunlight or in extreme temperature conditions.<br />
720 SOFTHAND CLEAR BASE<br />
Recommendations and statements made are based on International Coatings’ research and experience. Since International Coatings does not have any control over the conditions<br />
of use or storage of the product sold, International Coatings cannot guarantee the results obtained through use of its products. All products are sold and samples given without any<br />
representation of warranty, expressed or implied, of fitness for any particular purpose or otherwise, and upon condition that the buyer shall determine the suitability of the product for<br />
its own purpose. This applies also where rights of third parties are involved. It does not release the user from the obligation to test the suitability of the product for the intended<br />
purpose and application. REV090104<br />
86
Change language