2008 CATALOG WWW.ICCINK.COM

More documents

Recommendations

Info

Ink Modifiers: 1110LF Curable Reducer Cleanup: Mineral Spirits or Environmentally Friendly Screen Wash for Plastisol. Storage: HOLOGRAPHIC GLITTER PLASTISOL CONTINUED Keep indoors and store in a cool area. Recommend storage at 65°F to 90°F (18°C to 320°C). Avoid storage in direct sunlight or in extreme temperature conditions. Recommendations and statements made are based on International Coatings research and experience. Since International Coatings does not have any control over the conditions of use or storage of the product sold, Intemational Coatings cannot guarantee the results obtained through use of its' products. All products are sold and samples given without any representation of warranty, expressed or implied, of fitness for any particular purpose or otherwise, and upon condition that the buyer shall determine the suitability of the product for its own purpose. This applies also where rights of third parties are involved. It does not release the user from the obligation to test the suitability of the product for the intended purpose and application. Rev9199 76
13929 East 166th Street • Cerritos, California, USA 90702-7666 • Tel (562) 926-1010 • Fax (562) 926-9486 • www.iccink.com FEATURE EATURE EATURES EATURE � 108LF* is a Glow-in-the-Dark (phosphorescent) plastisol screen printing ink that produces a bright, greenish glow when exposed to light and viewed in a darken area. � 108LF can be used for direct print or cold peel transfer applications. � Ready for use from the container. *LF (Lead Free) Contains less than 0.025% lead. Application & Storage Information RE<strong>COM</strong>MENDED FABRICS INK APPLICATION SCREEN MESH AND EMULSION SQUEEGEE CURE TEMPERATURE CLEAN-UP PRODUCT PACKAGING STORAGE OF INK CONTAINERS PRODUCT MSDS IMPORTANT IMPORTANT INFORMATION INFORMATION INFORMATION 108 GLOW-IN-THE-DARK 100% cotton and some cotton/polyester white fabrics. For best results on dark fabrics, 108LF must be printed over a white base or Puff. Direct Prints: 108LF Glow-in-the-Dark ink should be used right from the container without any modifications. If thinning is required, use 1% to 5% by volume of 1110LF Curable Reducer. Adding too much reducer or other additives will diminish opacity and glow. Transfers (cold peel): It is important that the inks are only partially gelled, otherwise the inks will not have adequate adhesion during the final transfer application 60-230 t/in or 24-90 t/cm Monofilament Use 110-230 t/in or 43 –90 t/cm Monofilament for under basing. Any direct or indirect lacquer resistant emulsion. Use 35 to 70 micron capillary film for best results. 65-70 Durometer: Sharp Edge 60-90-60 Triple Durometer: Sharp Edge Direct prints: 325°F (163°C) entire ink film. Transfers: Gelation 225°F to 260°F (107°C to 127°C) Mineral Spirits or any environmentally friendly plastisol screen wash. 1 Gallon, 5 Gallon, or 30 Gallon Containers. Recommend storage at 65°F to 90°F (18°C to 32°C). Avoid storage in direct sunlight. Keep containers well sealed. Refer to material safety data sheet MSDS8. 1. 108LF Glow-in-the-Dark is a very transparent ink and works best when printed on white fabric or over a white base. 2. 108LF Is not a low bleed ink. Always test print the actual fabric to be printed before beginning production. We suggest long term testing on fabrics to determine if there are going to be any dye migration or bleeding problems. Dye migration or bleeding may not occur right away. 3. Do not fuse or cure the ink at too high a temperature (over 330°F or 166°C) as the phosphorescent pigment used in the ink can be damaged and not glow properly. 4. Adding too much reducer, soft hand additive or clear base will diminish glow. 5. Heavier ink deposits of 108LF will result in increased phosphorescence (glow brightness) and a longer glow after exposure to a bright light source. Depending on the amount of light exposure to the ink, the darkness of the of the area where the ink is being viewed and the eye sensitivity of the person viewing the ink, the glow may be visible anywhere from 30-seconds to several minutes. 6. When making cold peel transfers for dark fabrics, back transfers with white ink. 7. Cold peel transfers should be applied at 350°F to 375°F (177°C to 191°C), medium pressure (40 lbs.) for 10 to 15 seconds. 1 0 8 G LOW I N T H E DA R K Recommendations and statements made are based on International Coatings’ research and experience. Since International Coatings does not have any control over the conditions of use or storage of the product sold, International Coatings cannot guarantee the results obtained through use of its products. All products are sold and samples given without any representation of warranty, expressed or implied, of fitness for any particular purpose or otherwise, and upon condition that the buyer shall determine the suitability of the product for its own purpose. This applies also where rights of third parties are involved. It does not release the user from the obligation to test the suitability of the product for the intended purpose and application. REV090104 77
Page 1 and 2:
2008 CATALOG VOL. VII WWW.ICCINK.CO
Page 3:
CONTENTS This CD was designed to sh
Page 9 and 10:
McLogan Supply Company Inc 345 16th
Page 11 and 12:
Nazdar Michigan 687 Minnesota Avenu
Page 13 and 14:
SOUTH CAROLINA Nazdar Greensboro 70
Page 15 and 16:
INTERNATIONAL DISTRIBUTORS GUATEMAL
Page 17 and 18:
INTERNATIONAL COATINGS DIRECT PRINT
Page 19 and 20:
Application & Storage Information R
Page 21 and 22:
700 SERIES PLASTISOL INKS 13929 Eas
Page 23 and 24:
13929 East 166th Street • Cerrito
Page 25 and 26: 13929 East 166th Street • Cerrito
Page 27 and 28: FEATURES FEATURES � Ready for use
Page 31 and 32: Creating Performance Solutions 1392
Page 33 and 34: 7040 BLOCKER GRAY 7040 Blocker Gray
Page 47 and 48: 800 SERIES LF OPAQUE The 800 Series
Page 49 and 50: UltraMix ® 1200 PVC-FREE COLOR SYS
Page 52 and 53: UltraMix ® 7400 LF International C
Page 54 and 55: UltraMix ® 7900 LF PF Extra Low Cu
Page 56 and 57: UltraMix ® 9000 LF NYLON The Ultra
Page 59: UltraMix ® 11000 LF ATHLETIC The U
Page 64 and 65: SPECIALTY PRODUCTS When vibrant col
Page 66 and 67: 3805 LF SUPER STRETCH CLEAR This sp
Page 68 and 69: 3810 BLOWOUT BASE International Coa
Page 70 and 71: 3811 GRANITE BASE 3811 Granite Base
Page 72 and 73: 3802 FOIL RESIST ADDITIVE Internati
Page 88 and 89: TRANSFER PRODUCTS Add dimension and
Page 90 and 91: INSTA GRAPHIC SYSTEMS ® HEAT SEAL
Page 92 and 93: Model 138 Digital Manual Clam Press
Page 94 and 95: FOREVER DIGITAL TRANSFER PAPERS Int
Page 96 and 97: Forever Paper U.S. Distributors Pur
Page 98 and 99: Digital transfer PaPers fOr laser P
Page 100 and 101: Digital transfer PaPers fOr large f
Page 102 and 103: Digital transfer PaPers fOr ink jet
Page 104 and 105: Digital transfer PaPers fOr cOlOr c
Page 106 and 107: for almost two decades now, fOreVer
Page 108 and 109: OPTILUX ULTRA REFLECTIVE INK Intern
Page 110 and 111: Optilux Ultra Refl ective Ink Syste
Page 112 and 113: Optilux TM Reflective Film & Transf
Page 114 and 115: Special Effects Print Techniques Th
Page 116 and 117: Jacket Linings Jackets come in four
Page 118 and 119: Pre-Heating Because nylon fabric ch
Page 120 and 121: HOT PEEL OR HOT SPLIT TRANSFERS TRA
Page 122 and 123: INTERNATIONAL COATINGS TRANSFER PRO
Page 124 and 125: FABRIC DISCOLORATION AND HOW TO PRE
Page 126 and 127:
At what temperature do your inks cu
Page 128 and 129:
Can I intermix other companies’ i
Page 130 and 131:
MATERIAL SAFETY DATA SHEETS (MSDS)
Page 132 and 133:
MATERIAL SAFETY DATA SHEET PRODUCT
Page 134 and 135:
MATERIAL SAFETY DATA SHEET PRODUCT
Page 136:
Code Definition H: Health 3 F: Flam
show all

2008 CATALOG WWW.ICCINK.COM

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?