OPERATING MANUAL - Bauer

More documents

Recommendations

Info

13.1.2. Mounting the tow cable on pivot with skids • Turn the pivot into the towing direction. • Mount the clamp (A) on the end pipe of the first tower. • Fasten the tow cable (C) on clamp (A). • Fasten the pivot tow cables (D) on the pivot. • Fasten the tow cables (D) on the tow cable (C) with a cable clip according to the drawing. • The pulling force indicated by the arrows (1 and 2) should be adjusted in such a way that the front ends of the pivot skids are elevated about 100 to 200 mm in order to avoid “digging in” during the towing procedure. The ropes (arrows 3 and 4) must be tightly stretched, too, to avoid a “rolling” movement of the pivot. . NOTE ! Operating Manual for BAUER CENTERSTAR 5000 The pivot braces (F and G) are decisive for the pulling force of the pivot. Tow the machine only if the pivot is equipped with these braces (F and G). 34
13.1.3. Mounting the tow cables on 4-wheel pivot • Turn pivot into the driving direction, if necessary. For this purpose position the wheels tangentially to the pivot point and fix them with the braces. • Fasten the clamp on the end pipe of the first tower. • Mount and adjust cable with tightener (the first time) • Mount the drawbar (the first time) Operating Manual for BAUER CENTERSTAR 5000 35
Page 1 and 2: Version: X / 2005 OPERATING MANUAL
Page 3 and 4: Owner of the machine This machine w
Page 5 and 6: Product details Date of delivery ..
Page 7: 12.3 END STOP OR AUTOMATIC REVERSE
Page 10 and 11: 2 WARNING SYMBOLS Danger points on
Page 12 and 13: 3 GENERAL BAUER CENTERSTAR 5000 is
Page 14 and 15: 6. Never step on the system while i
Page 16 and 17: 7 PIVOT PANEL Design and materials
Page 18 and 19: NOTE! NOTE! Operating Manual for BA
Page 20 and 21: 3. Tighten the screws. 4. Check the
Page 22 and 23: 7.5 TOWER BOX ADJUSTMENT WARNING! M
Page 24 and 25: Operating Manual for BAUER CENTERST
Page 26 and 27: Operating Manual for BAUER CENTERST
Page 28 and 29: 9.1.1 Service plan Central tower Ex
Page 30 and 31: 9.1.4 Pretensioning forces and tigh
Page 32 and 33: 10.1 RESTART AFTER DOGLEGGING - WIT
Page 34 and 35: NOTE! CAUTION! CAUTION! CAUTION! CA
Page 36 and 37: DIMENSIONS OF BAUER CENTERSTAR Oper
Page 38 and 39: 12 OPTIONAL FEATURES 12.1 AUTOMATIC
Page 40 and 41: 12.9 END GUN SECTOR SHUT-OFF The en
Page 44 and 45: 13.2. TOWING THE CENTERSTAR ON THE
Page 46 and 47: 14 ELECTRICAL WIRING DIAGRAMS 14.1.
Page 48 and 49: 14.1.2 - Standard UNIVERSAL - contr
Page 50 and 51: 14.1.4 - Pivot panel - Universal Pr
Page 52 and 53: 14.1.6 -Pivot panel -Universal Pro
Page 54 and 55: 14.1.8 Control centre - Universal A
Page 56 and 57: 14.2 - Booster pump for endgun Oper
Page 58 and 59: 14.3.2 - Tower box with tower align
Page 60 and 61: 14.3.4 - Alignment control with tow
Page 62 and 63: 14.3.6 - End control with tower ali
Page 64 and 65: 14.3.8 End control with EMERGENCY S
Page 66 and 67: 14.3.10 - End control with Autoreve
Page 68 and 69: Has been done Part -Service Part -S
Page 70 and 71: Has been done Part -Service Part -S

OPERATING MANUAL - Bauer

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?