VISION SOFTWARE - Vision Engraving & Routing Systems

More documents

Recommendations

Info

48 Vision Software User's Guide You may either, type the filename and click OK, or you can select the name of the job with the mouse pointer and click OK. Note: If you use the pointer to click on the job name, the Comments field will display any comments that you might have saved with the job. There are two choices of Load Layout that you can choose from: Complete details or Dimensions Only. This is selected in the format box. Complete details will load the entire job that was saved including all of the text in the job. Details Only will load the entire job except for text that was in that job.
Chapter 4 - The Vision Menus 49 Note: Vision defaults the Job Load and Job Save directories to your hard drive C and in a directory called \Viswin\Jobs. If you would like to change the default Job Load and Job Save directory, you must do the following. Go to the Windows Start Menu, then to Programs, then to Vision Engraving Software and click on Edit Vision defaults. This will bring up the Cipher.sys file into the Windows Notepad. Go to the section in the file that says Default Job Load Directory and change it from C:\VisWin\Jobs to the drive and directory that you installed Vision into. You will also need to change the Default Save Directory. Save Job This feature allows you to save a job to your computers hard drive or to a floppy disk. Selecting this function brings up the Save Layout window.
Page 1 and 2: VISION SOFTWARE Reference Manual Re
Page 3 and 4: Table of Contents Table of Contents
Page 5 and 6: Welcome to Vision! Welcome to Visio
Page 7 and 8: Chapter 1 - Before You Begin 7 Chap
Page 9 and 10: Taking Inventory Chapter 1 - Before
Page 11 and 12: Chapter 1 - Before You Begin 11 3.
Page 13 and 14: Chapter 2 - Installing Vision 13 Ch
Page 15 and 16: Chapter 2 - Installing Vision 15 If
Page 17 and 18: Chapter 2 - Installing Vision 17 Se
Page 19 and 20: Chapter 2 - Installing Vision 19 Th
Page 21 and 22: Chapter 2 - Installing Vision 21 Se
Page 23 and 24: Select the type of system you have
Page 25 and 26: Chapter 2 - Installing Vision 25 1.
Page 27 and 28: Chapter 2 - Installing Vision 27 6.
Page 29 and 30: 10. Go to the Edit Menu and then to
Page 31 and 32: Chapter 3 - Using Vision - The Basi
Page 43 and 44: Chapter 4 - The Vision Menus 43 on
Page 45 and 46: Chapter 4 - The Vision Menus 45 to
Page 47: Load Job Chapter 4 - The Vision Men
Page 51 and 52: Chapter 4 - The Vision Menus 51 Not
Page 53 and 54: Chapter 4 - The Vision Menus 53 Whe
Page 55 and 56: Chapter 4 - The Vision Menus 55 The
Page 57 and 58: Chapter 4 - The Vision Menus 57 Pag
Page 59 and 60: Chapter 4 - The Vision Menus 59 Ign
Page 61 and 62: Chapter 4 - The Vision Menus 61 Thi
Page 63 and 64: Chapter 4 - The Vision Menus 63 Pla
Page 65 and 66: Copy Chapter 4 - The Vision Menus 6
Page 67 and 68: Chapter 4 - The Vision Menus 67 and
Page 69 and 70: Chapter 4 - The Vision Menus 69 3)
Page 71 and 72: Chapter 4 - The Vision Menus 71 8))
Page 73 and 74: Chapter 4 - The Vision Menus 73 The
Page 75 and 76: Chapter 4 - The Vision Menus 75 Thi
Page 77 and 78: Delete Subline Chapter 4 - The Visi
Page 79 and 80: Pause Point Chapter 4 - The Vision
Page 81 and 82: Chapter 4 - The Vision Menus 81 You
Page 83 and 84: Delete Line Chapter 4 - The Vision
Page 85 and 86: Chapter 4 - The Vision Menus 85 End
Page 87 and 88: Rotation This feature will allow yo
Page 89 and 90: Chapter 4 - The Vision Menus 89 Num
Page 91 and 92: Chapter 4 - The Vision Menus 91 X C
Page 93 and 94: Plate Menu Autoplate Chapter 4 - Th
Page 95 and 96: Chapter 4 - The Vision Menus 95 Bot
Page 97 and 98: Condense Mode Chapter 4 - The Visio
Page 99 and 100:
Chapter 4 - The Vision Menus 99 Num
Page 101 and 102:
Rotation This feature is used to ro
Page 103 and 104:
Chapter 4 - The Vision Menus 103 Ma
Page 105 and 106:
Chapter 4 - The Vision Menus 105 Pl
Page 107 and 108:
Chapter 4 - The Vision Menus 107 Th
Page 109 and 110:
Chapter 4 - The Vision Menus 109 1)
Page 111 and 112:
Chapter 4 - The Vision Menus 111 Cl
Page 113 and 114:
Chapter 4 - The Vision Menus 113 If
Page 115 and 116:
Chapter 4 - The Vision Menus 115 Li
Page 117 and 118:
Chapter 4 - The Vision Menus 117 To
Page 119 and 120:
Chapter 4 - The Vision Menus 119 No
Page 121 and 122:
Block Display Chapter 4 - The Visio
Page 123 and 124:
Re-order Chapter 4 - The Vision Men
Page 125 and 126:
Chapter 4 - The Vision Menus 125 X
Page 127 and 128:
Calculator Chapter 4 - The Vision M
Page 129 and 130:
International Characters Chapter 4
Page 131 and 132:
System Menu Devices Chapter 4 - The
Page 133 and 134:
Chapter 4 - The Vision Menus 133 X,
Page 135 and 136:
Chapter 4 - The Vision Menus 135 To
Page 137 and 138:
Chapter 4 - The Vision Menus 137 Se
Page 139 and 140:
Select the device you want. Chapter
Page 141 and 142:
You can choose the Windows font tha
Page 143 and 144:
About Vision Chapter 4 - The Vision
Page 145 and 146:
Chapter 5 - Other Features 145 Chap
Page 147 and 148:
Chapter 5 - Other Features 147 This
Page 149 and 150:
The next icon is the zoom out icon.
Page 151 and 152:
Re-Engrave Chapter 5 - Other Featur
Page 153 and 154:
Chapter 5 - Other Features 153 has
Page 155 and 156:
Chapter 5 - Other Features 155 You
Page 157 and 158:
Chapter 6 - Creating Sample Jobs 15
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
The job is now saved. Chapter 6 - C
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
The job is now saved. Chapter 6 - C
Page 171 and 172:
Appendix A: Hot Keys 171 Appendix A
Page 173 and 174:
Appendix A: Hot Keys 173 Within the
Page 175 and 176:
Appendix B: Troubleshooting Appendi
Page 177 and 178:
Appendix B: Troubleshooting 177 Sol
Page 179 and 180:
Appendix B: Troubleshooting 179 Cha
Page 181 and 182:
Appendix B: Troubleshooting 181 Thi
Page 183 and 184:
Appendix C: Error Messages Appendix
Page 185 and 186:
Index A About the Manual...........
Page 187:
Index 187
show all

VISION SOFTWARE - Vision Engraving & Routing Systems

Create successful ePaper yourself

Delete template?

Save as template?