ICRRFTSMRN+I - Ppe-pressure-washer-parts.com
ICRRFTSMRN+I - Ppe-pressure-washer-parts.com
ICRRFTSMRN+I - Ppe-pressure-washer-parts.com
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Applying Detergent with Adjustable Nozzle<br />
IMPORTANT: Use chemicals designed specifically for<br />
<strong>pressure</strong> <strong>washer</strong>s. Household detergents could<br />
damage the pump.<br />
CAUTION<br />
To apply detergent, follow these steps:<br />
1. Review use of adjustable nozzle.<br />
2. Prepare detergent solution as required by job.<br />
3. Place filter end of detergent siphoning tube into<br />
detergent container.<br />
CAUTION<br />
Pressure Washer Rinsing<br />
For Rinsing:<br />
1. Slide nozzle backward to high <strong>pressure</strong>, press<br />
trigger and wait for detergent to clear.<br />
NOTE: You can also stop detergent flow by removing<br />
detergent siphoning tube from container.<br />
2. Keep spray gun a safe distance from area you<br />
plan to spray.<br />
WARNING<br />
,Keep Sp!ayn_le b_een 8 t024 inches away from<br />
€leaningtrace<br />
, Operate this unit on a stablesurface:<br />
Imlm_mM_llgJm _'{'dil"_[ttlim m<br />
/ lIE IIEaiI/<br />
_r_ Ira<br />
, Be extremely carefulis youmust use the <strong>pressure</strong><br />
<strong>washer</strong> from a !adderi scaffo!djng or any other relatively<br />
', When inserting the fi!ter into a detergent solution bottle, .... Unstableiocatien........................................................<br />
route the tube s0 as t0 keep it fr0m inadvertently ............ ......<br />
c0nta_ing _e hot raUffler.<br />
Firrn!y graS#SpraygunWithb°th hands when us!nghigh<br />
<strong>pressure</strong> spray to ayoid injury if gun kicks back.<br />
4. Slide adjustable nozzle forward to low <strong>pressure</strong> 3. Apply a high <strong>pressure</strong> spray to a small area, then<br />
mode. Detergent cannot be applied with nozzle in<br />
check surface for damage. If no damage is found,<br />
high <strong>pressure</strong> position.<br />
it is okay to continue cleaning.<br />
5. MaKe sure garden hose is connected to water<br />
Start at top of area to be rinsed, working down<br />
inlet. Check that high <strong>pressure</strong> hose is connected<br />
with same overlapping strokes as you used for<br />
to spray gun and pump. Start engine.<br />
washing and applying detergent.<br />
6. Apply detergent to a dry surface, starting from<br />
bottom and working up.<br />
7. Allow detergent to =soak in" for 3-5 minutes before<br />
rinsing. Reapply as needed to prevent surface<br />
from drying.<br />
8. For washing, start at lower portion of area to be<br />
washed and work upward, using long, even,<br />
overlapping strokes.<br />
IMPORTANT: You must flush the chemical injection<br />
system after each use by placing the filter into a clean<br />
bucket of water and running the <strong>pressure</strong> <strong>washer</strong> in<br />
low <strong>pressure</strong> for 1-2 minutes.<br />
Automatic Cool Down System<br />
(Thermal Relief)<br />
If you run the engine on your <strong>pressure</strong> <strong>washer</strong> for<br />
3-5 minutes without pressing the trigger on the spray<br />
gun, circulating water in the pump can reach<br />
temperatures above 125=F. The system engages to<br />
cool the pump by discharging the warm water onto<br />
the ground.<br />
10