Compression Blow Forming for plastic containers - Sacmi
Compression Blow Forming for plastic containers - Sacmi
Compression Blow Forming for plastic containers - Sacmi
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
EN CBF (<strong>Compression</strong> <strong>Blow</strong> <strong>Forming</strong>) is a unique<br />
combination of compression molding to make the<br />
pre<strong>for</strong>m and blow molding to <strong>for</strong>m the container. The<br />
process begins with the raw material being introduced<br />
into a continuously operating extruder. The extruder<br />
provides a constant supply of material which is cut<br />
into predetermined precise pellets which are inserted<br />
into an open compression mold and thus begins<br />
the compression cycle portion of the process. The<br />
compression cycle molds the pre<strong>for</strong>m which is exactly<br />
the final weight of the container. The pre<strong>for</strong>m needed<br />
to produce the final container is temperature controlled<br />
to provide the blow process with the proper pre<strong>for</strong>m<br />
<strong>for</strong> blow <strong>for</strong>ming. This pre<strong>for</strong>m is carried into the blow<br />
mold to be <strong>for</strong>med into the desired container. No scrap<br />
or trimming is required. The <strong>containers</strong> are transferred<br />
in-line to the exit conveyor. The process is continuous<br />
permitting the machine to be compact and to control<br />
the container without release until all of the downstream<br />
operations are completed. This includes conducting<br />
all quality control operations without releasing the<br />
container and within the footprint of the machine.<br />
CN<br />
CBF( 压 塑 吹 瓶 成 型 ) 是 一 种 独 一 无 二 模 压 成 型<br />
一 体 机 , 它 可 以 包 括 从 瓶 胚 ( 压 塑 ) 到 吹 瓶 最 后<br />
至 容 器 成 型 的 过 程 。 整 个 生 产 流 程 开 始 于 将 原 料<br />
颗 粒 送 入 持 续 运 行 的 挤 出 机 ; 而 挤 出 机 则 将 会 源<br />
源 不 断 把 原 料 精 确 地 切 割 成 预 先 设 定 过 大 小 的 粒<br />
料 ; 切 割 后 的 粒 料 被 投 放 至 一 个 开 启 的 压 塑 模 具<br />
内 , 由 压 塑 工 艺 开 始 了 从 瓶 胚 到 理 想 容 器 的 成 型<br />
循 环 过 程 。<br />
在 吹 瓶 过 程 中 温 度 控 制 对 瓶 胚 成 型 起 到 关 键 作<br />
用 , 最 终 决 定 容 器 成 型 后 的 重 量 。 瓶 胚 被 置 于<br />
模 具 中 吹 塑 成 理 想 的 瓶 型 。 瓶 身 与 瓶 壁 齐 整 ,<br />
无 毛 边 , 成 品 重 量 与 客 户 的 要 求 完 全 一 致 。 容<br />
器 成 型 后 将 被 置 于 输 送 带 上 。 完 整 且 不 间 断 的<br />
生 产 过 程 保 证 了 出 瓶 的 一 致 性 。 此 外 , 生 产 流<br />
程 和 设 备 完 美 的 结 合 则 不 会 导 致 容 器 在 生 产 过<br />
程 中 滑 脱 , 各 阶 段 连 线 生 产 , 无 需 输 送 带 ; 在<br />
线 检 测 同 时 可 以 保 证 设 备 对 产 品 质 量 的 控 制 。