PINZA AMPERIMÃTRICA / CLAMP METER / - Ega Master

More documents

Recommendations

Info

To test the diode out of a circuit, connect the Meter as follows:1. Insert the red test lead into the Hz Duty% V terminal and the black test lead into theCOM terminal.2. Set the rotary switch to . Diode measurement mode is a default or press SELECT to selectmeasurement mode.3.. For forward voltage drop readings on any semiconductor component, place the red test lead onthe component’s anode and place the black test lead on the component’s cathode.Note:To obtain a more precise reading, you could remove the objects being tested from the circuitwhen measuring.When diode testing has been completed, disconnect the connection between the testing leadsand the circuit under test and remove testing leads from the input terminals.D. Testing for Continuity (see figure 6)Warning!To avoid damages to the Meter or to the devices under test, disconnectcircuit power and discharge all the high-voltage capacitors before measuringcontinuity.(figure 6)To test for continuity, connect the Meter as follows:1. Insert the red test lead into the Hz Duty% V terminal and the black test lead into theCOM terminal.2. Set the rotary switch to and press SELECT button to select measurement mode.3.. The buzzer sounds if the resistance of a circuit under test is less than 50 .4. The buzzer may or may not sounds if the resistance of a circuit under test is between 50 to100 .5. The buzzer does not sound if the resistance of a circuit under test is higher than 100 .Note:When continuity testing has been completed, disconnect the connection between the testingleads and the circuit under test and remove testing leads from the input terminals.28
E. Frequency Measurement (see figure 7)Warning!To avoid harms to you or damages to the Meter from eletric shock, do notattempt to measure voltages higher than 600V AC/DC, although readings maybe obtained.The resistance ranges are:10Hz, 100Hz, 1kHz, 10kHz, 100kHz, 1MHz and 10MHz.(figure 7)To measure frequency, connect the Meter as follows:1. Insert the red test lead into the Hz Duty% V terminal and the black test lead into theCOM terminal.2. Set the rotary switch to Hz.3.. Connect the test leads across with the object being measured. The measured value shows on thedisplay.Note:When frequency measurement has been completed, disconnect the connection between thetesting leads and the circuit under test, and remove the testing leads away from the input terminalsof the Meter.29
Page 3: INFORMACION GENERALEste manual de i
Page 6 and 7: FUNCION DE LOS BOTONESLa siguiente
Page 9 and 10: Los rangos de resistencia son:400 ,
Page 11 and 12: 2. Gire el selector hasta y presion
Page 13 and 14: Para medir la corriente, conecte el
Page 15 and 16: Nota:- Impedancia de entrada: 10M /
Page 17 and 18: la pinza, luego suelte el gatillo l
Page 19 and 20: NOTASIMPORTANTE!El fabricante no se
Page 21 and 22: OVERVIEWThis Operating Manual cover
Page 23 and 24: INTERNATIONAL ELECTRICAL SYMBOLSAC
Page 25 and 26: DISPLAY SYMBOLS (see figure 2)(figu
Page 27: (figure 4)To measure resistance, co
Page 31 and 32: To measure current, do the followin
Page 33 and 34: B. AC VoltageRange Resolution Accur
Page 35 and 36: Warning!The operating temperature m
Page 37 and 38: NOTESIMPORTANT!The maker will not t
Page 39: CERTIFICADO DE GARANTIAGUARANTEE CE

PINZA AMPERIMÃTRICA / CLAMP METER / - Ega Master

Create successful ePaper yourself

Delete template?

Save as template?

PINZA AMPERIMÃTRICA / CLAMP METER / - Ega Master