PINZA AMPERIMÃTRICA / CLAMP METER / - Ega Master

More documents

Recommendations

Info

E. Continuity TestRange Resolution Accuracy Overload protection100mAround ≤50 , thebuzzer beeps600VpRemark:- Open circuit voltage approximate 0.45V.- The buzzer may or may not beeps when the resistance of a circuit under test isbetween 50 ~100- The buzzer will not beep when the resistance of a circuit under test is >100 .F. FrequencyRange Resolution Accuracy Overload protection10Hz0.001Hz100Hz0.01Hz1kHz0.1Hz(0.1%+3)10kHz1Hz600Vp100kHz10Hz1MHz100Hz10MHz 1kHz For reference onlyRemark:- Input Sensitivity as follows:When ≤100kHz: ≥300mV rmsWhen > 100kHz:≥600mV rmsWhen > 1MHz: ≥800mV rmsG. Duty CycleRange Resolution Accuracy Overload protection0.1%~99.9% 0.1% For reference only 600VpH. DC CurrentRange Resolution Accuracy Overload protection40.00A 0.01A (2%+5)400A DC/AC400.0A 0.1A (2%+3)3.4
Warning!The operating temperature must be 0ºC ~40ºC when measuring currentRemark:- If the reading is positive, the current direction is from bottom to up. See figure 10, the frontcase face up while the bottom case face down. Hold the Meter tight, do now release. The Hallcomponents are very sensitive not only to the magnet but also to heat and machines reaction force.Any shock will cause the changing in reading in the short time. Follow the below procedure tomeasure current will be more precise:- Hold the Meter tight and press the lever to open the transformer jaw. Center the conductorwithin the transformer jaws, then release the Meter slowly until the transformer jaw is completelyclosed. Make sure the conductor to be tested is placed at the center of the transformer jaw,otherwise it will cause +1.0% deviation based on the stated accuracy.- Remove the transformer jaw.- Press REL to display zero.- Repeat the above 1. procedure.- The obtained reading will be more precise.I. AC CurrentRange Resolution Accuracy Frequency Response Overload protection40.00A 0.01A (2.5%+8)50Hz ~ 60Hz400A DC/AC400.0A 0.1A (2.5%+5)Warning!The operating temperature must be 0ºC ~40ºC when measuring currentRemark:- It may have 10 digits or less unstable or wrong digits, it will not affect measurement result.- Hold the Meter tight, do now release. The Hall components are very sensitive not only to themagnet but also to heat and machines reaction force. Any shock will cause the changing in readingin the short time. Follow the below procedure to measure current will be more precise:1. Hold the Meter tight and press the lever to open the transformer jaw. Center the conductorwithin the transformer jaws, then release the Meter slowly until the transformer jaw iscompletely closed. Make sure the conductor to be tested is placed at the center of thetransformer jaw, otherwise it will cause +1.0% deviation based on the stated accuracy.2. Remove the transformer jaw.3.. Press REL to display zero.4. Repeat the above 1. procedure.5. The obtained reading will be more precise.- Change to AC:Combine AC and True RMS response method. Input sine wave to adjust. Non sine wave mustfollow the below data to adjust:Peak factor: 1.4~2.0, add 1.0% on the stated accuracyPeak factor: 2.0~2.5, add 2.5% on the stated accuracyPeak factor: 2.5~3..0, add 4.0% on the stated accuracy.3.5
Page 3: INFORMACION GENERALEste manual de i
Page 6 and 7: FUNCION DE LOS BOTONESLa siguiente
Page 9 and 10: Los rangos de resistencia son:400 ,
Page 11 and 12: 2. Gire el selector hasta y presion
Page 13 and 14: Para medir la corriente, conecte el
Page 15 and 16: Nota:- Impedancia de entrada: 10M /
Page 17 and 18: la pinza, luego suelte el gatillo l
Page 19 and 20: NOTASIMPORTANTE!El fabricante no se
Page 21 and 22: OVERVIEWThis Operating Manual cover
Page 23 and 24: INTERNATIONAL ELECTRICAL SYMBOLSAC
Page 25 and 26: DISPLAY SYMBOLS (see figure 2)(figu
Page 27 and 28: (figure 4)To measure resistance, co
Page 29 and 30: E. Frequency Measurement (see figur
Page 31 and 32: To measure current, do the followin
Page 33: B. AC VoltageRange Resolution Accur
Page 37 and 38: NOTESIMPORTANT!The maker will not t
Page 39: CERTIFICADO DE GARANTIAGUARANTEE CE

PINZA AMPERIMÃTRICA / CLAMP METER / - Ega Master

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

PINZA AMPERIMÃTRICA / CLAMP METER / - Ega Master