cat.Enerlux.B-T.indd 1 19-01-2007 12:43:54 - Terasaki
cat.Enerlux.B-T.indd 1 19-01-2007 12:43:54 - Terasaki
cat.Enerlux.B-T.indd 1 19-01-2007 12:43:54 - Terasaki
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
RG2<br />
76<br />
APPARECCHIATURE . AUTOMATICHE . A PARETE • EQUIPMENT . AUTOMATIC . WALL-MOUNTED • APPAREILLAGES . AUTOMATIQUES . MURAUX<br />
H ± 2<br />
Prima di procedere all’installazione<br />
dell'apparecchiatura VERIFICARE<br />
ATTENTAMENTE IL CONTENUTO ARMONICO<br />
della rete di alimentazione e le prescrizioni<br />
indi<strong>cat</strong>e al paragrafo “CONDIZIONI DI<br />
SERVIZIO” o contattare il nostro Ufficio<br />
tecnico che fornirà le opportune indicazioni<br />
per un corretto impiego delle apparecchiature.<br />
Date le tolleranze di ammissibilità dei<br />
parametri di capacità e tensione definite dalle<br />
normative nazionali CEI EN 60831-1/2 ed<br />
internazionali IEC 831-1/2 ed eventuali<br />
componenti armoniche di lieve entità, è<br />
possibile che la corrente possa presentare un<br />
valore fino a 1,5 In.<br />
Esiste quindi la necessità di dimensionare i<br />
cavi di collegamento per una portata pari a<br />
1,5 In.<br />
Per un corretto funzionamento<br />
dell’apparecchiatura non si devono mai<br />
superare i limiti di tensione, corrente e<br />
temperatura previsti dalla normativa.<br />
Si consiglia di installare una protezione da<br />
sovratensioni d’origine atmosferica<br />
nell’impianto dove dovrà essere collegata<br />
l’apparecchiatura.<br />
L ± 2<br />
Ingresso linea<br />
Supply entry<br />
Entrée ligne<br />
L ± 2<br />
Before going ahead and installing the<br />
equipment CAREFULLY CHECK THE<br />
HARMONIC LOAD of the power supply<br />
network and the prescriptions stated under<br />
the heading “CONDITIONS OF SERVICE” or<br />
contact our Engineering Department that will<br />
provide suitable instructions for using the<br />
equipment correctly.<br />
Due to the permissible tolerances of the<br />
parameters of capacity and voltage defined<br />
by the national CEI EN 60831-1/2 and<br />
international IEC 831-1/2 standards and any<br />
small harmonic components, the current could<br />
be up to 1.5 In.<br />
It is, therefore, necessary to size the<br />
connecting cables for a capacity of 1.5 In.<br />
For the equipment to work properly, the<br />
voltage, current and temperature limits<br />
prescribed by the regulations must never be<br />
exceeded.<br />
It is recommended to install protection against<br />
overvoltage of atmospheric origin in the<br />
installation where the equipment is to be<br />
connected.<br />
DISEGNO TECNICO<br />
TECHNICAL DRAWING<br />
DESSIN TECHNIQUE<br />
INSTALLAZIONE INSTALLATION INSTALLATION<br />
P ± 2<br />
Avant de procéder à l’installation de<br />
l’appareillage, VERIFIER ATTENTIVEMENT LE<br />
CONTENU HARMONIQUE du réseau<br />
d’alimentation et les prescriptions figurant<br />
au paragraphe “CONDITIONS DE SERVICE” ou<br />
contacter notre Service technique, lequel<br />
fournira les indi<strong>cat</strong>ions pour un emploi correct<br />
des appareillages.<br />
Etant donné les tolérances d’admissibilité des<br />
paramètres de capacité et de tension définies<br />
par les réglementations nationales CEI EN<br />
60831-1/2 et internationales IEC 831-1/2, et<br />
les éventuelles composantes harmoniques de<br />
faible ampleur, il est possible que le courrant<br />
présente une valeur jusqu’à 1,5 In.<br />
Pour un bon fonctionnement de l’appareillage,<br />
ne jamais dépasser les limites de tension, de<br />
courant et de température prévues par la<br />
réglementation.<br />
Il est conseillé de prévoir une protection contre<br />
les surtensions d’origine atmosphérique dans<br />
l’installation à laquelle l’appareillage sera<br />
connecté.<br />
<strong>cat</strong>.<strong>Enerlux</strong>.B-T.<strong>indd</strong> 56 <strong>19</strong>-<strong>01</strong>-<strong>2007</strong> 13:13:10