2009 RS Multilingual f01.indd - Sonic Electronix

More documents

Recommendations

Info

Fig. 1 Confi guring the RS for Coaxial Operation tweeter lead wires Fig. 2 tweeter output-level switch. Higher switch settings mean more volume from the tweeter. CROSSOVER CONFIGURATION Step 1 Step 2 boot coaxial mounting post tweeter Steps 3–6 Steps 7–8 RS crossover INPUT jumper. Install only for 2-way confi gurations; do not install if bi-amping. The KICKER RS crossover can be confi gured as a conventional 2-way crossover by installing the included INPUT jumper into the - MID + -TW + input terminals as shown in Fig. 2. In this confi guration, the amplifi ed signal from your source unit or amplifi er should be wired to the + and - terminals indicated on the INPUT jumper. The RS crossover can also be confi gured for bi-amp wiring by removing (or simply not installing) the INPUT jumper. To use the bi-amp confi guration, you must connect two amplifi ed signals to each crossover (you will need at least four amplifi er channels). Set the tweeter output-level switch to 0 dB, +3 dB, or +6 dB. Higher switch settings will result in more volume from the tweeter. 4 RSCOMPONENTSYSTEM +6 +3 +0 INPUT OUTPUT -MID+ -MID+ OUTPUT -TW+ -TW+ - INPUT + 2009 RS Multilingual f01.indd 4 11/21/2008 10:57:25 AM
WIRING We recommend using 16 gauge (or larger) wire. The RS components are rated at 4 ohms and work with any source unit or amplifi er designed to operate at a 4 ohm load. Make sure your source unit or amplifi er is rated for 4 ohm operation. Crossover in 2-way confi guration | One component set per channel At least two amplifi er channels are needed for stereo operation (only one channel is shown) woofer source unit / amplifi er + - OUT -MID+ + - - IN + + OUT -MID+ - - IN + -OUT+ OUT -TW+ + - + - Crossover in 2-way confi guration | Two component sets per channel Requires two complete RS systems (four woofers, four tweeters, four crossovers) At least two amplifi er channels are needed for stereo operation (only one channel is shown) Crossovers wired in series OUT OUT -TW+ -MID+ - IN + source unit / amplifi er crossover - OUT + OUT -TW+ tweeter 2009 RS Multilingual f01.indd 5 11/21/2008 10:57:28 AM + - 5
Page 1 and 2: RS RSCOMPONENTSYSTEM RS65.2 RS60.2
Page 3: CONFIGURATION Before mounting and w
Page 7 and 8: WOOFER MOUNTING The KICKER RS compo
Page 9 and 10: the narrow part of the front angle
Page 11 and 12: ACOUSTICS LIMITED WARRANTY KICKER w
Page 13 and 14: CONFIGURACIÓN Antes de montar y re
Page 15 and 16: CABLEADO Se recomienda utilizar un
Page 17 and 18: MONTAJE DEL WOOFER Los altavoces co
Page 19 and 20: lograr el ángulo de funcionamiento
Page 21 and 22: Autorisierter KICKER-Händler: Kauf
Page 23 and 24: Abb. 1 Anordnung des RS für Koaxia
Page 25 and 26: Frequenzweiche in bi-amp- Anordnung
Page 27 and 28: Verkleidung Kurze Befestigungsmutte
Page 29 and 30: GRILLEINBAU 2009 RS Multilingual f0
Page 31 and 32: CONFIGURATION Avant de monter et de
Page 33 and 34: CÂBLAGE Nous conseillons d’utili
Page 35 and 36: MONTAGE DU WOOFER Les composants Ki
Page 37 and 38: ague angulaire arrière, faire pass
Page 39 and 40: INTERNATIONAL WARRANTY Contact your

2009 RS Multilingual f01.indd - Sonic Electronix

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?