Logamax plus - Buderus

More documents

Recommendations

Info

3 Installation3.5 Replacing the air ventB Remove the plastic cover from the top of the appliance.3.6 Mounting the gas supply pipe andcondensate trapB Fill the new condensate trap ( fig. 1, [5]) with waterbefore re-installing it. This is to prevent exhaust gasesfrom entering the room.B Install the gas supply pipe according to figures 13 to23 of the gas supply pipe instructions ( fig. 1, [11]).fig. 8 Removing the plastic coverB Remove the float cap.6 720 641 697-008.1TD3.7 Testing for gas leaksNOTICE: electrical short circuit.Leaks may be caused to pipes and screwconnections during servicing activities.B Carry out a proper leak test.B Cover damageable parts before leaktesting.B Only use approved leak detection agents.B Do not spray the leak testing agent ontocables, plugs or electrical connectionlines. Do not allow it to drip onto themeither.6 720 641 697-009.1TDfig. 9 Removing the float capB Remove the valve case by pulling it upwards throughthe opening in the housing.DANGER: gas explosion.What to do if you smell gas:B No open fire. Do not smoke.B Avoid formation of sparks. Do not touchany electric switch, phone, electric plug orbell.B Shut off the main gas supply.B Open windows and doors.B Notify all occupants.B Leave the building.B Immediately call your gas supplier, heatingcontractor or fire department from a phoneoutside the building.B Open the gas shut-off valve.6 720 641 697-010.1TDfig. 10 Removing the valve case for the automatic airpurging systemB Install the new valve case and all other parts ( fig. 1,[7]) in reverse order.6 720 641 697-039.1TDfig. 11 Gas shut-off valve openB Check all joints and gaskets affected by thereplacement activities for gas leaks.B In case of a gas leak, close the gas shutt-off valve( fig. 2) and take the safety precautions mentionedabove.B Check again all joints and gaskets and repair theleakage.B Open the gas shut-off valve ( fig. 11) and checkagain for gas leaks.6Logamax plus GB142-24/30/45/60 - We reserve the right to make any changes due to technical modifications!
Returning the gas supply pipe and water sample43.8 Filling the applianceB Switch on the heating system by setting the mainsswitch [1] to position "1". P0.0 appears in the displayof the control panel telling you that there is no systempressure.10090Eco0110120Aut130140900110130150170190AutD) Do not use this appliance if any part has been underwater. Immediately call a qualified service technicianto inspect the appliance and to replace any part of thecontrol system and any gas control which has beenunder water.B Wait five (5) minutes to clear out any gas. Then smellfor gas, including near the floor. If you smell gas, STOP!Follow "B" in the safety information above. If you do notsmell gas, go to the next step.B Install the casing again.0 1Reset1.2.16 720 641 697-013.1TDfig. 12Mains switch to „ON“B Fill the heating system to a pressure of around 20 psi(1.5 bar).B Observe the pressure on the control panel or the P/Tgauge in the pump manifold (if equipped) for theheating circuit. The fill pressure of the system shouldbe at least the required inlet pressure for the expansiontank plus 7.2 psi (0.5 bar). The minimum pressure is15 psi (1.0 bar) (on a cold system). The maximumpressure is 44 psi (3.0 bar) (if the heating mediumtemperature is at its highest possible level). If thispressure is exceeded, the pressure relief valve willopen.3.9 Start up the applianceFor your safety, read before lighting.DANGER: due to not following theseinstructions.B If you do not follow these instructionsexactly, a fire or explosion may resultcausing property damage, personal injuryor loss of life.B Follow these operating instructions.A) This appliance does not have a pilot. It is equipped withan ignition device which automatically lights the burner.Do not try to light the burner by hand.B) BEFORE OPERATING smell all around the appliancearea for gas. Be sure to smell next to the floor becausesome gas is heavier than air and will settle on the floor.C) Use only your hand to push in or turn the gas controlknob. Never use tools. If the knob will not push in orturn by hand, don't try to repair it, call a qualified servicetechnician. Force or attempted repair may result ina fire or explosion.6 720 641 697-011.1TDfig. 13 Installing the casingB Set the thermostat or other operation control to thedesired setting.B Connect the appliance to the power supply.B Switch on the appliance using the mains switch( fig. 12).B Check all gas fittings and water fittings for leaks.4 Returning the gas supplypipe and water sampleB Fill out the return form ( fig. 1, [10]).B Place the return form, labeled gas supply pipe andlabeled bottle with water sample in the return box( fig. 1, [9]).B Place the address label ( fig. 1, [8]) on the return box.B Adhere the shipping label from the return form to thebox and drop it off at your nearest UPS shipping center.Service level: UPS Standard - receiver paysCustomer number: 228785.B If you follow the procedure as described in thismanual you will receive a compensation of US$90 for the extra work.2.3.Logamax plus GB142-24/30/45/60 - We reserve the right to make any changes due to technical modifications! 7
Page 1 and 2: Service kit instructions gas supply
Page 3 and 4: Safety and general instructions11 S
Page 5: Installation3B Use the radiator key
Page 9 and 10: Remarques et consignes de sécurit
Page 11 and 12: Installation3B régler le thermosta
Page 13 and 14: Installation3B Contrôler l'absence
Page 15 and 16: 4NotesLogamax plus GB142-24/30/45/6

Logamax plus - Buderus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?